Texas Instruments CC2543EM Manuale utente

December 2011

Web sites: www.ti.com/lprf

E2E Forum: www.ti.com/lprf-forum

Make sure to subscribe to the Low-Power RF

Newsletter to receive information about updates to

documentation, new product releases, and more.

CC2543-CC2544 Development Kit Quick Start Guide

Opening the Box and Running the Packet Error Rate Test Application

1. Kit Contents

•2 x SmartRF05EB (the two large boards)

•2 x CC2543 Evaluation Module (CC2543EM)

•2 x Pulse W1010 Antennas

•1 x CC2544 Dongle

•Cables

•Documentation

The RF boards in this kit are FCC and IC

certified and tested/complies with ETSI/R&TTE

over temperature from 0 to +35°C. The antenna,

W1010 from Pulse, is a ¼ wave dipole antenna

with 2 dBi gain.

Caution! The kit contains ESD

sensitive components. Handle with

care to prevent permanent damage.

2. Hardware Requirements

To run the example described in this Quick

Start Guide, you would need either two

CC2543Ems mounted on SmartRF05

Evaluation Boards (SmartRF05EB - Rev 1.8.1

or later). Or a single CC2543EM mounted on

a SmartRF05EB and a CC2544 Dongle

(powered through USB). The SmartRF05EBs

are included in the CC2543-CC2544DK.

More information about the SmartRF05EB can

be found in www.ti.com/lit/swru210.

The CC2543EM boards can also be plugged

into a battery board (see www.ti.com/tool/soc-

bb) for standalone operation.

3. Hardware Setup

Connect the antenna to the SMA connector on

the CC2543EM. Tighten the antenna’s screw

firmly on to the SMA connector. If not properly

connected, you might see reduced RF

performance.

Next, mount the CC2543EMs firmly on to

connectors P5 and P6 on the SmartRF05EB.

The CC2544 Dongle can be connected to any

USB port to power the device.

Caution! To minimize risk of injury, avoid

touching components during operation if

symbolized as hot.

4. Power Options

There are several ways of applying power to the

SmartRF05EB.

•2 x 1.5 V AA Alkaline Batteries

•USB

•External Power Supply

For the batteries and USB, there are voltage

regulators on the SmartRF05EB that will set the

on-board voltage to 3.3 V. The external power

supply should set a voltage that does not exceed

3.3 V. Note that there should only be one

active power source at any one time.

Warning! To minimize risk of personal injury or

property damage, never use rechargeable

batteries to power the board.

5. Power the

Boards

Find jumper P11 on

the top side of each

SmartRF05EB. This jumper is used to set the

power source for the board. Set P11 to “1-2” if

you are using battery power. Set P11 to “2-3” if

you are using USB or an

external power supply.

Once you have set P11,

find switch P8 on the top

side of each

SmartRF05EB. To power up the boards, flip the

switch from the “OFF” position to “ON”.

Do not leave EVM powered when

unattended.

6. Start-up Screen

The CC2543EMs and the CC2544 Dongle

will be pre-loaded with a Packet Error Rate

(PER) test application. The LCD screens on

the two SmartRF05EBs should display the

messages below:

A green led (LED2 on CC2544Dongle, LED1

on SmartRF05EB) will blink continuously

After the application has started.

7. Choosing Mode

The application can be used between two

CC2543EM’s or between a single CC2543EM

and the CC2544 Dongle. There are two possible

modes of operation called “Remote” and

“Master”. The CC2544Dongle is set to master by

default as it is the only option for this device in

this application. After button S1 is pushed at the

start up screen, the mode selection screen

(showed to the left below) will appear. The

Remote mode is shown by default. Press the

joystick up and down to change between master

and remote mode and press button S1 to

confirm.

In the remote mode all the parameters for the

current PER test must be set up before the test

begins.

8. Master Mode

In “Master” mode, the radio will repeatedly (once

every 10 milliseconds) send out a “beacon”

signal (250 kbps, GFSK modulation, 160 kHz

deviation, 2479 MHz) and listen for a response

from the remote device. Once the beacon is

acknowledged by the “Remote”, the actual PER

test begins. During the PER test, packets are

sent at a fixed repetition rate of 10 msec.

No more actions are needed from the user for

this master device to work.

9. Frequency Selection

When the remote mode is chosen, a series of

settings must be configured to set up the link for

the PER test. The frequency must be selected

first. Move the joystick up or down to change the

frequency (channel) and press S1 to confirm the

choice.

10. Modulation Setup

There are 6 different modulation schemes

available for this application. The different

bitrates are 250 Kbps, 500 Kbps, 1Mbps and 2

Mbps. MSK modulation is used for the 500 Kbps

rate and GFSK for the rest. Move the joystick up

or down to change the scheme and press S1 to

confirm the choice.

11. Packet Length

The packet length can be set to 10, 16, 32, 64 or

120 bytes. Move the joystick up or down to

change the packet length and press S1 to

confirm the choice.

12. Number of Packets

The total number of packets to be sent for each

run can be set to 200, 1000, 5000, 10000 and .

Move the joystick up or down to change the

number of packets and press S1 to confirm the

choice.

13. Test Running

The remote device acknowledges the beacon

signal from the master and sends the

configuration packet. The PER test begins. While

the master device is sending packets the yellow

led will be lit on the smartRF05EB (“LED3”) or

the red led on the CC2544 Dongle (“LED1”).

14. PER Test Summary

The first results screen will display the number of

packets received without errors (“Good”), the

number that were received with a CRC error

(“Bad”), and the number that were expected but

not received (“LOST”). Push button S1 to

proceed to the second results screen.

15. Repeat Test

The final screen allows the test to be repeated by

pushing “Button 1” (S1). Note that the set up data

is maintained. If you wish to enter different test

parameters, you may do so by pushing “EM

RESET” button, located at the approximate

center of the SmartRF05EB.

Additional Tools and Links

SmartRF™ Studio

SmartRF Studio allows you to configure the radio,

run RF performance tests, and run link tests

between the two SmartRF05EBs.

SmartRF Studio can be downloaded from

www.ti.com/smartrfstudio

SmartRF Flash Programmer

Texas Instruments has a simple tool which can

be used to program and flash the CC2543 and

CC2544.

SmartRF Flash Programmer can be

downloaded from www.ti.com/tool/flash-

programmer

IAR Embedded Workbench

To develop software, program, and debug the

CC2543 and CC2544, you should use IAR

Embedded Workbench for 8051.

More information on IAR EW8051, including a

free evaluation version download, can be found at

www.iar.com/ew8051.

EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS

Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following

conditions:

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user

indemnifies TI from all claims arising from the handling or use of the goods.

Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/ kit may be

returned within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS

THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER

WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE

INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY

INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to

handling the product. This notice contains important safety information about temperatures and voltages. For

additional information on TI's environmental and/or safety programs, please visit www.ti.com/esh or contact TI.

No license is granted under any patent right or other intellectual property right of TI covering or relating to any

machine, process, or combination in which such TI products or services might be or are used. TI currently deals

with a variety of customers for products, and therefore our arrangement with the user is not exclusive. TI

assumes no liability for applications assistance, customer product design, software performance, or

infringement of patents or services described herein.

Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265

REGULATORY COMPLIANCE INFORMATION

As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not

be subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules.

For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for

ENGINEERING DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not

considered by TI to be a finished end product fit for general consumer use. It generates, uses, and can radiate

radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to

part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency

interference. Operation of the equipment may cause interference with radio communications, in which case the

user at his own expense will be required to take whatever measures may be required to correct this interference.

General Statement for EVMs including a radio

User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally

allocated frequency and power limits. Any use of radio frequencies and/or power availability of this EVM and its

development application(s) must comply with local laws governing radio spectrum allocation and power limits for

this evaluation module. It is the user’s sole responsibility to only operate this radio in legally acceptable

frequency space and within legally mandated power limitations. Any exceptions to this is strictly prohibited and

unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses

from local regulatory authorities, which is responsibility of user including its acceptable authorization.

For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

FCC Interference Statement for Class A EVM devices

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Interference Statement for Class B EVM devices

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EVMs annotated as IC – INDUSTRY CANADA Compliant

This Class A or B digital apparatus complies with Canadian ICES-003.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Concerning EVMs including radio transmitters

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

Concerning EVMs including detachable antennas

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically

radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the

user guide with the maximum permissible gain and required antenna impedance for each antenna type

indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.

Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité

ont pu vider l’autorité de l'utilisateur pour actionner l'équipement.

Concernant les EVMs avec appareils radio

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de

licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d'en compromettre le fonctionnement.

Concernant les EVMs avec antennes détachables

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une

antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le

but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type

d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne

énumérés dans le manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque

type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal

indiqué, sont strictement interdits pour l'exploitation de l'émetteur.



Important Notice for Users of this Product in Japan

This development kit is NOT certified as Confirming to Technical Regulations of

Radio Law of Japan!

If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with

respect to this product:

(1) Use this product in a shielded room or any other test facility as defined in the notification #173

issued by Ministry of Internal Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of

Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan,

(2) Use this product only after you obtained the license of Test Radio Station as provided in Radio Law

of Japan with respect to this product, or

(3) Use of this product only after you obtained the Technical Regulations Conformity Certification as

provided in Radio Law of Japan with respect to this product.

Also, please do not transfer this product, unless you give the same notice above to the transferee.

Please note that if you could not follow the instructions above, you will be subject to penalties of Radio Law of

Japan.

Texas Instruments Japan Limited

(address) 24-1, Nishi-Shinjuku 6 chome, Shinjukku-ku, Tokyo, Japan

http://www.tij.co.jp



!"#$%&'()*+,

!"#$%&'()*+,!"#$%&'()*+,

!"#$%&'()*+,

-./0123456789:;<=>)?@ABCD

-./0123456789:;<=>)?@ABCD-./0123456789:;<=>)?@ABCD

-./0123456789:;<=>)?@ABCD

-EF*"#$%GH)3IJKLMN*'OIPQ*RSTU*VW<X()R'YZ[\]&@A^*

_"+,ZY`RD

abcJKLdefgh6ih1jh1k%6lZmn18o3p28qrstuvh173k_wOxT'J

Kyz{*|}~_"#$R'YZD

ac}*<X"#$R'YZD

ac456789:;<X"#$R'YZD

?I-EF3I*"#$%&'()*+,<I%HR@II_

R*HA^D

   <MN>R93IJKL*g]8$`T]&<"¡,ZY`RD

q-¢0£¤¥¦§¤¨©ª§¨«¬®

q-¢0£¤¥¦§¤¨©ª§¨«¬®q-¢0£¤¥¦§¤¨©ª§¨«¬®

q-¢0£¤¥¦§¤¨©ª§¨«¬®

¯°±²³´µ²³¶·¸¹ºbk

¯°±²³´µ²³¶·¸¹ºbk¯°±²³´µ²³¶·¸¹ºbk

¯°±²³´µ²³¶·¸¹ºbk

µ²³»¼½©

µ²³»¼½©µ²³»¼½©

µ²³»¼½©

http://www.tij.co.jp



EVALUATION BOARD/KIT/MODULE (EVM)

WARNINGS, RESTRICTIONS AND DISCLAIMERS

For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated,

this EVM is not a finished electrical equipment and not intended for consumer use. It is intended solely for use

for preliminary feasibility evaluation in laboratory/development environments by technically qualified electronics

experts who are familiar with the dangers and application risks associated with handling electrical mechanical

components, systems and subsystems. It should not be used as all or part of a finished end product.

Your Sole Responsibility and Risk. You acknowledge, represent and agree that:

1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but

not limited to Food and Drug Administration regulations, if applicable) which relate to your products and

which relate to your use (and/or that of your employees, affiliates, contractors or designees) of the EVM for

evaluation, testing and other purposes.

2. You have full and exclusive responsibility to assure the safety and compliance of your products with all

such laws and other applicable regulatory requirements, and also to assure the safety of any activities to

be conducted by you and/or your employees, affiliates, contractors or designees, using the EVM. Further,

you are responsible to assure that any interfaces (electronic and/or mechanical) between the EVM and any

human body are designed with suitable isolation and means to safely limit accessible leakage currents to

minimize the risk of electrical shock hazard.

3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property

damage, injury or death, even if the EVM should fail to perform as described or expected.

4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing

materials

Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and

environmental considerations per the user guidelines. Exceeding the specified EVM ratings (including but not

limited to input and output voltage, current, power, and environmental ranges) may cause property damage,

personal injury or death. If there are questions concerning these ratings please contact a TI field representative

prior to connecting interface electronics including input power and intended loads. Any loads applied outside of

the specified output range may result in unintended and/or inaccurate operation and/or possible permanent

damage to the EVM and/or interface electronics. Please consult the EVM User's Guide prior to connecting any

load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field

representative. During normal operation, some circuit components may have case temperatures greater than

60 C as long as the input and output are maintained at a normal ambient operating temperature. These

components include but are not limited to linear regulators, switching transistors, pass transistors, and current

sense resistors which can be identified using the EVM schematic located in the EVM User's Guide. When

placing measurement probes near these devices during normal operation, please be aware that these devices

may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable

in electronic measurement and diagnostics normally found in development environments should use these

EVMs

Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its

licensors and their representatives harmless from and against any and all claims, damages, losses, expenses,

costs and liabilities (collectively, "Claims") arising out of or in connection with any use of the EVM that is not in

accordance with the terms of the agreement. This obligation shall apply whether Claims arise under law of tort

or contract or any other legal theory, and even if the EVM fails to perform as described or expected.

Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in

safety critical applications (such as life support) where a failure of the TI product would reasonably be expected

to cause severe personal injury or death, such as devices which are classified as FDA Class III or similar

classification, then you must specifically notify TI of such intent and enter into a separate Assurance and

Indemnity Agreement.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Texas Instruments Microcontrollore

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuale utente

Texas Instruments

Texas Instruments C2000 LED BoosterPack Manuale utente

Texas Instruments

Texas Instruments TIDA-00830 Manuale utente

Texas Instruments

Texas Instruments CC2533EMK Manuale utente

Texas Instruments

Texas Instruments CC1120 Manuale utente

Texas Instruments

Texas Instruments MSP430C311S Manuale utente

Texas Instruments

Texas Instruments MSP430F663x Manuale utente

Texas Instruments

Texas Instruments LaunchPad C2000 F280015 Series Manuale utente

Texas Instruments

Texas Instruments AM5728 Manuale utente

Texas Instruments

Texas Instruments AFE722 Series Manuale utente

Texas Instruments

Texas Instruments MSP430F67491 Manuale utente

Texas Instruments

Texas Instruments TMS570LS3137 Manuale utente

Texas Instruments

Texas Instruments AM243x Manuale utente

Texas Instruments

Texas Instruments AM437x Manuale utente

Texas Instruments

Texas Instruments MSP430FR6989 LaunchPad Manuale utente

Texas Instruments

Texas Instruments CC3235 SimpleLink Series Manuale del prodotto

Texas Instruments

Texas Instruments MSP430F6765 Manuale utente

Texas Instruments

Texas Instruments TMS320C6000 DSP Guida

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale di programmazione

Texas Instruments

Texas Instruments AM243 Series Manuale utente

Texas Instruments

Texas Instruments CC2540 Manuale di istruzioni

Texas Instruments

Texas Instruments TMS570LS31 HDK Manuale utente

Texas Instruments

Texas Instruments Chipcon Products CC1050DK Manuale utente

Texas Instruments

Texas Instruments TI-InnovatorHub Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente

Silicon Laboratories

Silicon Laboratories C8051F800 Manuale utente

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuale utente

Mikroe

Mikroe click Proximity 2 Manuale utente