Texas Instruments SmartRF CC900DBK Manuale di programmazione

SWRU063

Quick Start Instructions

Rev. 1.1

SmartRF

®

CC900DBK Demonstration Board Kit

SWRU063 Page 2 of 2

How to get a quick start using CC900DBK

The CC900DBK Demonstration Board Kit demonstrates the CC900 RF transceiver in a very

simple application. The Demonstration Board includes a complete CC900 transceiver, an

AVR micro-controller, an integrated PCB antenna and a battery. It provides a complete

example of a low-cost, low-power system using the CC900 transceiver. Please note that the

design is optimised for low cost applications and not for maximum range. In order to evaluate

range and performance, use the CC900DK.

Important:

•Do NOT short-circuit the battery terminals at any time.

•The use of radio transceivers is regulated by international and national rules. Before

transmitting a RF signal, please contact your local telecommunication authorities to check

if you are licensed to operate the transceiver.

To get the Kit up and running, follow these steps:

1. The CC900DB runs off a 3.6V Lithium battery. If the battery is not mounted, solder it to

the pads at the rear side of the board.

2. Examine the LED. If it does not blink at regular intervals, push the “ON” button.

3. If the LED still does not blink, remove the battery and reconnect it. If this does not help,

exchange the battery with a new one.

4. Press the “ON” buttons on both Demonstration Boards so that both are blinking. They are

now in polling reception mode, checking for data each time the LED is lit.

5. Press the “TX” button on one of the boards. The demonstration board sends a data

packet of approximately 1.5 second duration.

6. If the other demonstration board received the message without errors, its LED will blink

the Morse code for “victory”. It then sends an acknowledgement message in return.

7. If the first board receives the acknowledgement message, it will also blink “victory” in

Morse code.

If a demonstration board has not received a message or had any buttons pressed for two

minutes, it will enter power-down mode, ensuring minimum power consumption. To wake it,

press the “On” button.

If communication does not succeed on the first attempt, try again. RF noise may have

corrupted the message. Signal processing in the small micro-controller has been kept to a

minimum, therefore a small noise burst may corrupt the message. When holding the

demonstration board, do not touch the antenna or the VCO tank. Ideally, keep your hand as

far away from the antenna as possible in order to get the best performance. If you wish to

reprogram the Demonstration Board using the Development Kit, make sure to:

•Use the cable supplied in the Development Kit

•Remove the battery when reprogramming

•Use the correct parallel port. If you are using the correct port, you will receive an error

message if you try to program the EEPROM and no Demonstration Board is inserted

For further information, see the CC900DB Demonstration Board User Manual, which can be

downloaded from our website (http: www.chipcon.com)

Indice

Altri manuali Texas Instruments Scheda madre

Texas Instruments

Texas Instruments DS90UB95 Q1EVM Series Manuale utente

Texas Instruments

Texas Instruments C28 Series Manuale utente

Texas Instruments

Texas Instruments DRV814x-Q1EVM Manuale utente

Texas Instruments

Texas Instruments INA253EVM Manuale utente

Texas Instruments

Texas Instruments TPS7A13EVM-057 Manuale utente

Texas Instruments

Texas Instruments ADS131B26Q1EVM-PDK Manuale utente

Texas Instruments

Texas Instruments INA250EVM Manuale utente

Texas Instruments

Texas Instruments TPA3002D2EVM Manuale utente

Texas Instruments

Texas Instruments LMG3410EVM-031 Manuale utente

Texas Instruments

Texas Instruments OPT3101 Manuale utente

Texas Instruments

Texas Instruments TAS5602EVM2 Manuale utente

Texas Instruments

Texas Instruments TPS7A26EVM-021 Manuale utente

Texas Instruments

Texas Instruments INA282-286EVM Manuale utente

Texas Instruments

Texas Instruments CDCE72010 Manuale utente

Texas Instruments

Texas Instruments TMP110 Manuale utente

Texas Instruments

Texas Instruments LP8580EVM Manuale utente

Texas Instruments

Texas Instruments TLV840EVM Manuale utente

Texas Instruments

Texas Instruments ADC-PHI-PRU-EVM Manuale utente

Texas Instruments

Texas Instruments TPS65010EVM-230 Manuale utente

Texas Instruments

Texas Instruments TPS25810EVM-745 Manuale utente

Texas Instruments

Texas Instruments TPS92611-Q1 Manuale utente

Texas Instruments

Texas Instruments DAC53608 Manuale utente

Texas Instruments

Texas Instruments LM25119EVAL Manuale utente

Texas Instruments

Texas Instruments TPS560200 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente