TierTime UP300D Manuale utente
1
Tiertime UP300D
User Manual
www.tiertime.com
2
Index
1. Safety and Printing Environment.........................................................................................5
1.1 Safety Precautions........................................................................................................................5
1.2 Printing Environment..................................................................................................................6
1.3 One Year Warranty..................................................................................................................... 6
1.4 Compliance................................................................................................................................... 6
2. Unboxing............................................................................................................................... 7
2.1 Unboxing the UP300D................................................................................................................. 7
2.2 What’s in the box......................................................................................................................... 8
3. Introduction...........................................................................................................................9
3.1 Main Parts of UP300D.................................................................................................................9
4. Printer Installation..............................................................................................................10
4.1 Install the Print Board...............................................................................................................10
4.2. Install the Software UP Studio 3.0...........................................................................................11
4.3 Update the Touchscreen Firmware.......................................................................................... 11
5. Prepare UP300D for Printing.............................................................................................12
5.1 Connectivity................................................................................................................................12
5.2 Auto Calibration........................................................................................................................ 12
5.3 Auto Calibration from Touchscreen........................................................................................ 12
5.3 Load the Filaments.....................................................................................................................13
6. First Print............................................................................................................................ 16
6.1. Slicing......................................................................................................................................... 16
6.1.1 Open UP Studio 3....................................................................................................................16
6.1.3. Load an STL file.....................................................................................................................17
6.1.4. Auxiliary Support (A.S.)........................................................................................................18
6.2 Connect and Send Print Job to Printer....................................................................................20
6.3 Remove Printed Models.............................................................................................................21
7. Printer Calibrations.............................................................................................................22
7.1 Nozzle Height Measurement..................................................................................................... 23
7.2 Setup Nozzle Height Value through Wand..............................................................................23
7.3 Matrix Leveling (9-Point Compensation)................................................................................ 25
7.3.1 Auto Matrix Leveling through Wand................................................................................... 26
7.4 Manual Calibration....................................................................................................................27
8. Introduction to UP Studio 3 Package.................................................................................29
9. Introduction to the UP Studio, the Slicer........................................................................... 31
9.1 Interface...................................................................................................................................... 31
9.2 Quick Setting Bar.......................................................................................................................31
9.3 Print Layout Tools..................................................................................................................... 31
9.4 Support Editor............................................................................................................................33
3
9.5 Print Settings.............................................................................................................................. 36
9.5.1 Print Modes............................................................................................................................. 37
9.6 Introduction to Print Parameters.............................................................................................38
9.6.1. Slicer Settings......................................................................................................................... 39
9.6.2 Path...........................................................................................................................................43
9.6.3.Special...................................................................................................................................... 45
9.6.4 Speed........................................................................................................................................ 46
9.6.5 Temperature............................................................................................................................ 47
9.6.6 Seams Settings......................................................................................................................... 47
9.6.7 Printer...................................................................................................................................... 48
9.6.8 Extruder...................................................................................................................................48
9.6.9 Script........................................................................................................................................ 48
Chapter 10. Material Library (Mat Lib) and Custom Materials........................................... 50
Chapter 11. Part Sub-setting...................................................................................................51
11.1 Optimize along Z axis (Vertical Sections)..............................................................................51
11.2 Optimize on X-Y plane............................................................................................................ 52
12. Wand - the Printer Hosting Software............................................................................... 54
12.1 Wand Interface .......................................................................................................................54
12.2 Wi-Fi Connection..................................................................................................................... 56
12.3 Ethernet Connection............................................................................................................... 56
12.4 Editing Network Configuration..............................................................................................57
13. Touchscreen Introduction.................................................................................................58
13.1 Printer Status Bar.................................................................................................................... 58
13.2 Main Menu................................................................................................................................59
13.3 Material.....................................................................................................................................60
13.4 Print...........................................................................................................................................62
13.5 Calibrate................................................................................................................................... 65
13.6 Information...............................................................................................................................66
13.7 Config........................................................................................................................................ 67
13.8 Network Connection................................................................................................................ 68
13.9 Wi-Fi Network Connection and Settings:..............................................................................70
13.10. Initialize .................................................................................................................................72
Chapter 14. Print Boards........................................................................................................ 73
14.1 Perf Glass Boards.....................................................................................................................73
14.2 Flex Glass Boards.....................................................................................................................73
14.3 Glass Surface............................................................................................................................ 73
Chapter 15. Extruders............................................................................................................. 74
15.1 Single Extrusion Print Heads..................................................................................................74
15.2 Convergence Dual Extruder................................................................................................... 75
Chapter 16. Maintenance........................................................................................................76
4
16.1 Replacing Nozzle:.....................................................................................................................76
16.3 Extruder Maintenance.............................................................................................................77
16.3.3 Convergence Dual Extruder................................................................................................ 79
16.3.3 Releasing the heater block....................................................................................................80
16.3.4 Remove/Replace Stepper Motor.......................................................................................... 82
16.3.5 Remove the extrude block................................................................................................... 82
16.4 Unclogging Extruder................................................................................................................83
16.4.1 Partial Blockage.................................................................................................................... 83
16.4.2 Completely Blockage.............................................................................................................84
16.4.3 Remove blockage at heater module.....................................................................................84
16.5 Clean the Waste Tray.............................................................................................................. 85
16.6 Dual Filtration System.............................................................................................................86
Chapter 17. Specification........................................................................................................ 87
Chapter 18. Customer Service and Community.....................................................................88
5
1. Safety and Printing Environment
1.1 Safety Precautions
1. The UP300D 3D printer requires the power adapter provided by the original
manufacturer, otherwise the machine could be damaged or even cause fire. Keep
the power adapter away from water and out of high temperature environments.
2.During printing, the temperature of the nozzle of the printer could reach 300°C and
the temperature of the print platform could be over 100°C. Do not touch these parts
with your bare hands when the printer is in the operation mode, not even with the
heat resistant gloves included in the accessories, as the temperature could damage
the gloves and injure your hands.
3. During printing, the print head and other mechanical parts move at high speed.
Touching these parts while they are moving could cause injuries.
4. Wear goggles when removing the supporting material from models or detaching
models from the build plates.
5. When printing with plastic filaments, the process could generate slight and, for
some people, annoying odor. It is recommended to run the printer in a well ventilated
environment. We also suggest to keep the printer in an environment with a stable
temperature as unwanted cooling could cause adverse effects to the print quality.
6. When using the “Extrude” function, make sure there is enough space between the
print head nozzle and the build platform. 50mm is recommended, otherwise the
nozzle could be blocked.
7. Fasten moving parts. Tie back loose hair, secure loose clothing and keep all
printer doors closed during operation.
8. Do not leave the printer unattended during operation. Watch to make sure the first
a few layers adhere correctly.
9. Adult Supervision: Adult supervision is required in the presence of children. Small
printed parts are a choking hazard, and always keep sharp tools away from children.
6
1.2 Printing Environment
As the slight odor could be generated during printing, keep the printer in a well
ventilated environment. The UP300D's ideal working temperature is between 15°C
and 30°C with a relative humidity between 20–50%. Printing at temperatures out of
this range could cause adverse effects to the printing process and print quality.
1.3 One Year Warranty
Tiertime and its authorized resellers warrant to the original purchaser that this
product is free from defects in material and workmanship. Tiertime or its resellers will
for one year, at its option, repair or replace at no charge for parts and labor from the
date you purchased the product from Tiertime or a reseller. Print heads, and Print
Boards are warranted for thirty (30) days.
• Tiertime reserves the right to determine the validity of all warranty claims.
• Warranty is voided if the product serial number has been altered or removed.
• Warranty is voided if the product has been misused or damaged or if evidence is
present that the product was altered, modified, or serviced by unauthorized service
people.
For the detailed Warranty and Service Level Agreement, please visit our website
https://www.tiertime.com.
1.4 Compliance
FCC
RoHS
CE
7
2. Unboxing
2.1 Unboxing the UP300D
1. Cut open the tape on the top of the cardboard box, and open the box from the top.
2. Take out the two boards on the top foam, and remove the top foam.
3. Remove the plastic cover and the square shaped foam wrapping around the
machine.
4. Lift the printer out of the cardboard box using two handles on both sides of the
printer, and place it on a flat surface.
5. Open the Top Lid and remove all the tights and foams inside the printer. There are
six tights in the machine.
6. Open the Front Door, and take out the two foams and two extruders beneath the
build platform. As figures show below:
7. Take out the roll of filament, the accessory box and the power cord at the bottom
of the cardboard box.
8. Put all the foams back to the box, and keep the box for the future use.
8
2.2 What’s in the box
The Convergence dual extruder is installed on the UP300D.
1. Accessory box
One ABS Type single extruder
One USB Cable
One Pliers
One Scarper
One Nozzle Wrench: 8mm
One Nozzle Wrench: 10mm
One Pair of Gloves
One SD Card Reader
One SD Card
One Calibration Card
One Nozzle Height Detector
Two PTFE Tube: Shorter one for PLA Extruder; Longer one for TPU Extruder
Three Allen Keys: 2mm, 2.5mm, 3mm
Three Nozzles: 0.2mm, 0.4mm, 0.6mm
2. In the UP300D box
One roll of 500g PLA Filament
One roll of 500g Water Soluble Support Filament
One Flex Glass Board
One Perf Glass Board
One Power Adapter
One Power Cord
Notice: All accessories may be subject to change without prior notice. If anything is
missing, please contact your local distributor, or Tiertime’s global technical support
9
3. Introduction
3.1 Main Parts of UP300D
1. Dual Filter
2. Build Platform
3. Waste Tray
4. Front Door
5. Touchscreen
6. Front USB Port
7. Top Lid
8. Right Side Handle
9. Heated Filament Chamber
10. Power Switch
11. Ethernet Socket
12. USB Port
13. Power Socket
Y- Axis
X-Axis
Z-Axis
Build Platform
Extruder Mount
10
4. Printer Installation
4.1 Install the Print Board
Find the “perforated print board”, slide the board onto the build platform and make
sure to push the board all the way to the back.
Plug in the power on the back of the UP300D.
Altri manuali per UP300D
1
Indice
Altri manuali TierTime Stampante 3D
TierTime
TierTime UP600 Manuale utente
TierTime
TierTime UP Mini 2 ES Manuale utente
TierTime
TierTime UP BOX Manuale utente
TierTime
TierTime UP BOX Manuale utente
TierTime
TierTime UP300D Manuale utente
TierTime
TierTime UP BOX+ Manuale utente
TierTime
TierTime Filament Dryer PRO Manuale utente
TierTime
TierTime UP300 Manuale utente
TierTime
TierTime UP BOX Manuale di installazione e funzionamento
TierTime
TierTime UP mini 3 Manuale utente
