TimeTools T100 Manuale

T100 NTP Network Time Server

19-0218

Hardware Installation Guide

Models Covered: T100

Document Number: T1 00-01

7 January 017

The latest version of this user guide can be obtained from www.TimeTools.co.uk.

T100 Hardware Installation Guide. Page

Important Safety Information:

Important Safety Information - Read the safety instructions before using this product.

1. Please read the manuals and retain for future reference. Please follow all instructions and heed all warnings.

. Do not use this apparatus near water.

3. Clean only with dry cloth.

4. Install in accordance with the manufacturer’s instructions.

5. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers)

that produce heat.

6. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

7. Only use attachments as specified by the manufacturer.

8. The unit has no user serviceable parts inside. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as power-supply cord or power adapter is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain

or moisture, does not operate normally, or has been dropped.

9. Use the power adapter to disconnect the apparatus from the AC mains. The power adapter shall remain easily

accessible.

10. To completely disconnect unit power from the AC mains, disconnect the unit’s power adapter from the mains

socket. To reconnect power, plug the unit’s power adapter into the mains socket following all safety instructions and

guidelines.

11. Never push objects of any kind into this product through cabinet apertures as they may touch dangerous voltage

points or short out parts that could result in fire or electric shock.

For PERMANENT Y CONNECTED EQUIPMENT, a readily accessible disconnect device shall be incorporated

external to the equipment.

For P UGGAB E EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily

accessible.

Use only the supplied power adapter with the T100 NTP time server.

T100 Hardware Installation Guide. Page 3

CAUTION:

Before installing and configuring any T-Series NTP server

appliance, please read the manuals and retain for future reference.

Please follow all instructions and heed all warnings.

Full product documentation can be found on the supplied CD or at

www.timetools.co.uk.

While reasonable efforts have been taken in the preparation of this document to ensure its accuracy, TimeTools Limited

assumes no liability resulting from any errors or omissions in this manual, or from the use of the information contained

herein.

All claims based on information publicly available at time of printing.

All product or service names mentioned in this document are trademarks of the companies with which they are

associated.

T100 Hardware Installation Guide. Page 4

Table of Contents

1 Introduction................................................................................................................................................. 5

2 Key Features............................................................................................................................................... 5

3 Scope of Supply.......................................................................................................................................... 6

3.1 Optional Extras......................................................................................................................................................... 6

4 Front Panel.................................................................................................................................................. 7

4.1.1Alarm Indicator................................................................................................................................................... 7

4. USB Port................................................................................................................................................................... 7

4.3 Power Socket .......................................................................................................................................................... 7

5 Rear Panel................................................................................................................................................... 8

5.1 Ethernet Port - Eth0.................................................................................................................................................. 8

5. Console.................................................................................................................................................................... 8

5.3 GPS Antenna Connection......................................................................................................................................... 8

6 Installation................................................................................................................................................... 9

6.1 Locating the T100..................................................................................................................................................... 9

6. Antenna Connection................................................................................................................................................. 9

6.3 Connecting Ethernet................................................................................................................................................. 9

6.4 Connecting RS 3 Serial Console Cable...............................................................................................................10

6.5 Applying Power ..................................................................................................................................................... 10

7 Configuration............................................................................................................................................ 11

8 Certification and Compliance.................................................................................................................. 12

8.1 RoHS Compliance Statement................................................................................................................................. 1

8. REACH Regulation (EC) No 1907/ 006.................................................................................................................1

8.3 Environmental Policy.............................................................................................................................................. 1

8.4 EC Declaration Of Conformity................................................................................................................................1

9 Warranty.................................................................................................................................................... 14

T100 Hardware Installation Guide. Page 5

1 Introduction

Network Time Protocol (NTP) can be used to synchronize the time on network clients, across an IP network, to the

correct time of an NTP time server. TimeTools NTP Servers provide a stratum 1 NTP Time Server for ensuring the time is

correct across an entire network.

The Network Time Server acquires time from the GPS satellite constellation and distributes time across a network using

the TCP/IP Network Time Protocol (NTP).

2 Key Features

16-Channel, High Sensitivity GPS Timing Receiver.

Can operate with outdoor, indoor or window located antenna, saving on cabling costs.

Timing receiver synchronises to less than 15 nanoseconds (GPS Locked).

NTP accurate to less than 3 microsecond (3x10-6 seconds) UTC (GPS Locked).

Synchronize in excess of 100,000 clients.

10/100 Mbit auto-sensing, auto-MDIX Ethernet ports.

IPv4 and IPv6 Internet Protocol.

Extremely cost-effective.

Universal AC/DC mains power adapter for world-wide operation.

Made in UK, with 1 -month warranty and free lifetime support.

*1. Assuming standard 1 8 sec NTP polling frequency.

T100 Hardware Installation Guide. Page 6

3 Scope of Supply

TimeTools T100 shipment typically includes the following components:

T100 GPS NTP Server Appliance.

T-3040 Pole Mounting GPS Antenna .

MT4-GPS Antenna Mount.

TCX-010 10m (30 ft) RG58 Cable.

GE1 I07-P1J 7.5V DC Universal Power Supply.

RS 3 Serial Console Lead.

Quick Start Guide.

CD containing user-guide, installation guide and white-papers.

3.1 Optional Extras

TCX-010 10m RG58 Cable.

TCX-030 30m RG58 Cable.

TCX-050 50m LMR195 Equivalent Cable.

TCX-100 100m LMR400 Equivalent Cable.

Custom cable lengths available on request.

SPP-GPS Multi-strike maintenance-free surge suppressor

T-AD 00-8 GPS Amplifier – 0db

GPS over optical fibre systems.

GPS Splitters – to 3 way, compact or rack-mount.

Digital NTP Wall clocks.

Analog NTP Wall clocks.

T100 Hardware Installation Guide. Page 7

4 Front Panel

The T100 has the following front panel indicators/connectors: Alarm, USB, Power.

4.1.1 Alarm Indicator

A red / green bi-colour LED on the T100 front panel indicates status and fault conditions.

4.2 USB Port

A USB port is provided for convenient and easy installation of firmware updates. Standard USB flash memory devices

can be used for firmware updates.

4.3 Power Socket

A .5mm DC power jack accepts .5 or .1 mm diameter plugs. The supplied power adapter can be used to power the

device. Use only the power adapter supplied by TimeTools with the T100.

T100 Hardware Installation Guide. Page 8

5 Rear Panel

The rear of the T100 has the following connectors: Eth0, Antenna, Console.

5.1 Ethernet Port - Eth0

The T100 has a single RJ45 10/100 MBit auto-sensing, auto-MDIX Ethernet port labelled Eth0.

Link: 10/100 Mbit, auto-sensing, auto-MDIX

Connector: RJ45

Cable Type: CAT 5.0

Modes: Half/Full Auto-negotiation.

5.2 Console

The Console port is a 9-way D-type female RS 3 serial connection for device configuration using dumb terminal

emulator. Null modem cable supplied for connection to standard 9-way PC serial interface.

RS 3 Console port pin-outs:

Pin : RX

Pin 3: TX

Pin 5: GND

The appliance has a secondary serial port for optional serial time code output. It is combined into the same 9-way D-type

connector as the console port. A custom serial cable is required to utilise the secondary serial port.

Secondary RS 3 Serial Port pin-outs:

Pin 7: TXB

Pin 8 : RXB

5.3 GPS Antenna Connection

The GPS antenna connector is a 50 ohm TNC female connector. It accepts a coax cable to a 5V GPS antenna. Use only

the antenna and cable supplied by TimeTools with the T100.

Connector: TNC female, 50 ohm

Cable: Coax, 50 ohm

Antenna Output Voltage: 5VDC

T100 Hardware Installation Guide. Page 9

6 Installation

6.1 ocating the T100

Locate the appliance safely in a rack, on a shelf, or in a cupboard. The device should not be supported by the attached

cables.

CAUTION:

Do not install the T100 appliance where the operating ambient

temperature may drop below 0°C (3 °F) or exceed 50°C (1 °F).

6.2 Antenna Connection

The T100 antenna connection is a TNC female RF connector. It is provided for connection of an active 5 volt GPS

antenna via a coax cable.

WARNING:

Any local installation regulations for outdoor or rooftop mounted

antennas in the country where the antenna is installed must be

observed.

Please refer to the GPS/GNSS Antenna Installation Guide (Document Number: T1 0 -01) for further information on

antenna installation.

6.3 Connecting Ethernet

The T100 has a single 10/100 Mbit BaseT RJ45 auto-sensing, auto-MDIX Ethernet port.

The auto MDI-X feature, automatically detects the required cable connection type and configures the connection

appropriately, removing the need for crossover cables for peer to peer connection.

Connect one end of a CAT-5 patch cable to the RJ-45 network interface on the rear of the T100. Connect the other end

to a port on your network switch.

Alternatively, the T100 can be connected directly to a host PC Ethernet network port using a CAT-5 patch cable

for configuration purposes.

IMPORTANT:

When first installing the T100 on your network, ensure that no other

device on your network conflicts with the default IP address of the

appliance.

Default IP Address (Eth0): 19 .168.3.

T100 Hardware Installation Guide. Page 10

6.4 Connecting RS232 Serial Console Cable

The T100 Console port is a RS 3 serial port on a standard 9-way D-type connector. The console serial port can be

used configure the device from a host PC.

Using the supplied null modem cable, connect the T100 console port to the RS 3 serial port on a PC.

A terminal emulation program, such as Hyper-Terminal or Putty, can then be used to configure the device.

Terminal settings:

Connect Using: Direct to COMx (where x is the serial port number)

Bits per second: 115 00

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

Terminal Emulation: VT100 / ANSI

Please refer to the T-Series User Guide (Document Number T1300-01) for configuration information.

6.5 Applying Power

The T100 has a .5 mm power jack on the front panel of the appliance.

Apply power by connecting the supplied power adapter into the power jack at the rear of the NTP server and into an

appropriate AC power source.

CAUTION:

For PERMANENTLY CONNECTED EQUIPMENT, a readily

accessible disconnect device shall be incorporated external to the

equipment.

For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed

near the equipment and shall be easily accessible.

Power Adapter Specification:

Manufacturer: MEAN WELL Enterprises Co., Ltd.

Model: GE1 I07-P1J

Input Voltage Range: 90 ~ 64VAC

Input Frequency Range: 47 ~ 63Hz

Output Voltage: 7.5VDC 1.33A

Altri manuali per T100

Indice

Altri manuali TimeTools Server

TimeTools

TimeTools DirekTronik 119-0219 T300 Manuale

TimeTools

TimeTools T100 Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente