Toshiba BMS-LSV4E Manuale utente

Model:

BMS-STBN E

(for Intelligent Server model BMS-LSV4E only)

INSTALLATION MANUAL

BACnetTM SOFTWARE

CONTENTS

Precautions for Safety.................................................................................................................... 1

Before Installation .......................................................................................................................... 1

Elements of the Intelligent Server ................................................................................................. 2

1 CF (Compact Flash) card Installation ....................................................................................... 3

2 Setting .......................................................................................................................................... 3

3 Installation.................................................................................................................................... 4

4 Cable Connection ....................................................................................................................... 6

• Thank you very much for purchasing this TOSHIBA BACnet Software.

• Please read this manual carefully beforehand for proper installation of the software.

Precautions for Safety

• Read these “Precautions for Safety” carefully before installation.

• The precautions described below include important items regarding safety. Observe them without fail.

• After the installation work, perform a trial operation to check for any problem.

• Ask an authorized dealer or qualified installation professional to install or reinstall the

software.

• Perform installation work properly according to this Installation Manual.

• Do not modify the unit.

• Perform wiring correctly in accordance with specified the current capacity.

Failure to do so may result in short-circuiting, overheating, or fire.

• Connect the specified cables for the terminals securely to prevent external forces from

affecting them.

Failure to do so may result in disconnection, overheating, or fire.

CAUTION

Before Installation

No.

Quantity

Item

Intelligent Server Software

Cable

Closed end wire joint

Installation Manual

Remarks

Compact Flash card

RS-485 cable for Intelligent Server

No.

Type

Wire size

Length

Signal line

For RS-485

Description

2-core shield wire

1.25 mm2, 500m max. (total length)

Use the following wiring materials to connect signal lines. (Procured on site)

Check the following package contents.

This CF (Compact Flash) card is the software for the Intelligent Server (Model: BMS-LSV4E) only.

Prepare the Intelligent Server to use this card. This card is not applicable to BMS-LSV2E.

NOTE

Elements of the Intelligent Server

AC inlet (AC IN)

Power switch (POWER)

Serial port 2 (PORT 2)

Serial port 1 (PORT 1)

Ethernet port 2 (Ethernet 2)

Ethernet port 1 (Ethernet 1)

Error indication LED (red)

General-purpose switch 1

SERVICE LED (green)

INITIALIZE LED (red)

RUN LED (green)

LON T/R LED (green)

Maintenance switch

Shutdown request switch

Reset switch

LON service switch

Perspective view

INTELLIGENT SERVER

Front view INTELLIGENT SERVER

General-purpose switch 2

General-purpose LED1 (green)

Item

Temperature

Temperature Change

Humidity

Vibration

Shock

Operation

0 to 40 °C

15 °C/H

10 to 90 %RH

(without condensation)

2.45 m/s2or the less

24.5 m/s2or the less

Specification of Installation Environment

(1) Ambient Conditions

The specification of ambient conditions is shown below.

■■

■Ambient Specification

Storage

-20 to +60 °C

15 °C/H

10 to 90 %RH

(without condensation)

4.91 m/s2or the less

49.0 m/s2or the less

Item

Power Supply

Grounding

Rated Voltage

Tolerable Range

Frequency

Power Consumption

Tolerable Power

Interruption

(2) Power Supply Conditions

The specification of power supply conditions is shown below.

■■

■Power Supply Specification

Specification

100/240 V, AC

Single phase with grounding

85 - 132 V, AC / 180 - 264 V, AC

50/60 Hz ± 3 Hz, or the less

40 VA

20 ms, or the less

Exclusive grounding

(Grounding resistance: 100 ohms, or the less)

END LED (green)

General-purpose LED2 (green)

CF (Compact Flash) card Installation

• Do not insert or remove the CF (Compact Flash) card during power on of the Intelligent Server.

Doing so may cause a failure.

• If the CF (Compact Flash) card is not inserted properly, the Intelligent Server will not work.

REQUIREMENT

Insert the attached CF (Compact Flash) card fully into the CF (Compact Flash) card slot on the side of

the Intelligent Server.

234

1234

OFF ON ON OFF

1234

RS-485 mode set

switch

AC inlet side LED indicator side

RS-485 operation mode setting

The RS-485 mode set switch is provided on the bottom board of the Intelligent Server.

Set the switch as follows:

Setting

If the RS-485 mode set switch is set

incorrectly, the Intelligent Server will

not work.

NOTE

CF (Compact Flash) card

4 Not used

(Note 1) Transmit data sent from the Intelligent Server is not received by

the same server during transmission.

(Note 2) Transmit data sent from the Intelligent Server is also received

by the same server during transmission.

OFF

A terminator resistor is connected between TX(+) and TX(-).

No terminator resistor is connected between TX(+) and TX(-).

A terminator resistor is connected between RX(+) and RX(-).

No terminator resistor is connected between RX(+) and RX(-).

Half-duplex mode (Note 1)

Full-duplex mode (Note 2)

CF (Compact Flash) card slot

Do not install the unit in any of the following places.

• Humid or wet place

• Dusty place

• Place exposed to direct sunlight

• Place where there is a TV set or radio within one meter

• Place exposed to rain (outdoors, under eaves, etc.)

REQUIREMENT

Intelligent Server Installation Method and Orientation

There are two ways to install the Intelligent Server as shown below: (1) rack mount (2) surface mount.

The rack mount installation requires a support bracket for a 19-inch rack. Please contact us if you need

the support bracket.

(1)Rack mount

A support bracket is required to be fixed to the

bottom (rear side) of the unit.

(2)Surface mount

Standard installation

308.4 30.830.8

30 133 35

Screw hole for wall

mount (M4 × 4 pcs.)

(Unit: mm)

AC inlet side LED side

Installation

Installation (continued)

Installation Space and Maintenance Space

The installation space and the maintenance space must be determined before installation.

These spaces depend on installation method.

Installation Space

The values in the following table are required for installation space in each direction. Select an installation

place that allows good air ventilation.

Top

Rear

Left side

Front

Right side

Item

Installation space

Direction

Top

Bottom

Front

Rear

Right side

Left side

Rack mount

100

Location adjacent to wall permitted (*1)

Surface mount

100

Location adjacent to wall permitted (*1)

100

(*1) “Location adjacent to wall permitted” means that the unit can be installed close to the wall on that side.

Maintenance Space

Maintenance space is required for installation and maintenance of the unit.

Front

INTELLIGENT

SERVER

1000

: Maintenance Space

: Installation Space

(Unit: mm)

Rear

(Unit: mm)

Cable Connection

AC Power Cable Connection

Power cable is not supplied for the Intelligent Server. Prepare a 3-core power cable conforming

to applicable safety standards. Be sure to connect the earth line of the power cable securely.

REQUIREMENT

• Insert an AC power cable into the AC inlet of the unit.

• Connect the power cord plug to an outlet (100V - 240 V, AC).

• Install a breaker on the primary side of the outlet.

• Make sure that the outlet is earthed.

REQUIREMENT

Ethernet wire Connection

The Ethernet wires should be connected by professional service personnel.

NOTE

Serial Port (RS-485) Connection

• Check that the power switch of the Intelligent Server is turned off.

• Connect the attached RS-485 wire to the serial port 1 (PORT 1). Secure the wire to the Intelligent

Server using the two screws (right and left) attached to the RS-485 wire connector.

Connection to the TCS-NET Relay Interface

• TxRx(+) Connection

Connect three of the four wires of RS-485 wire (red wire/orange wire/wire from the terminal board RS-

485 A of the TCS-NET Relay Interface) together with the attached closed end wire joint. The red and

orange wires can be connected directly to the terminal board RS-485 A of the Relay Interface.

• TxRx(-) Connection

Connect three of the four wires of RS-485 wire (brown wire/yellow wire/wire from the terminal board RS-

485 B of the TCS-NET Relay Interface) together with the attached closed end wire joint. The brown and

yellow wires can be connected directly to the terminal board RS-485 B of the Relay Interface.

Ethernet1 PORT1

RS-485

RTS

TXD TX(+)

TX(-) TxRx(+)

TxRx(-)

RX(+)

RX(-)

RXD

OFF

100 ohm

10k ohm

RS-485

The RS-485 signal

wire has polarity.

If connected with

incorrect polarity, the

unit will not work.

Do not connect or

disconnect the wire

during control

operation.

Doing so may cause a

malfunction.

NOTE

Shield wire open

(insulated)

Connect the

shield wires

of the 2 wires

INTELLIGENT SERVER

Closed end

wire joint

Attached wire

Block diagram of PORT 1

Red/Orange

Brown/Yellow

TCS-NET

Relay Interface

TCS-NET

Relay Interface

Brown

Orange

Yellow

Red

Trial operation should be checked by professional

service personnel.

NOTE

• • • Trademarks: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

• BACnet is a registered trademark of ASHRAE(American Society of Heating, Refrigerating and

Air-Conditioning Engineers, Inc.).

• Compact Flash and CF are trademarks of SanDisk Corporation.

• Ethernet is a registered trademark of Xerox Corporation.

• Lon Talk, LonWorks and Neuron are registered trademarks of Echelon Corporation in the United States

and other countries.

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Appearance and Size

370

19839(5)

CAUTION

Do not remove.

WARNING

Do not decompose.

Unit in mm

EH99852301

Indice

Altri manuali Toshiba Server