TPI 1010a Manuale utente
1010a
Rev. 3.x & Above Meters
Indoor Air Quality Meter
The Value LeaderTM
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Contents
1. Introduction
2. General Overview
3.0 Front View
3.1 Soft Keys
3.2 Back View
4. Operation
4.1 Turning On & Off / Performing a Test / Main Display
4.2 Selecting Temperature Units
4.3 Ambient / Dew Point / Wet Bulb Temperature Display
4.4 Temperature / Clock Display Modes
4.5 Activating the Backlight
4.6 Printing Measurements
4.7 Setting Date and Time
4.8 Setting CO Alarm Level
4.9 Ambient Air CO2 Reset
5. Calculating % Outside Air
5.1 % Outside Air (Temperature)
5.2 % Outside Air (Carbon Dioxide)
6. Data Logging
7. Retrieving Logged Data
8. Technical Specifications
9. Maintenance & Troubleshooting
9.1 Battery Replacement
9.2 Service
10. Technical Information
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
1. Introduction
Thank you for purchasing TPI brand products. The TPI 1010a Indoor
Air Quality (IAQ) Meter is a state of the art, easy to use tester designed
to provide you with the necessary measurements to monitor and make
adjustments to air handling devices. The instrument is ruggedly con-
structed and comes with a 3 Year unit and 2 Year sensor Guarantee.
2. General Overview
The 1010a IAQ meter uses state of the art sensors to measure humidi-
ty, carbon monoxide (CO), carbon dioxide (CO2), and temperature. The
CO and CO2 sensors in your meter will need to be replaced periodically
and calibration is recommended once every year.
The CO sensor is electrochemical and this type of sensor is always
active once installed in the unit. Therefore the time the unit is off and
not being used must be taken into account when determining sensor
life. The sensors in your analyzer are warranted for two years. This
warranty does not cover sensors damaged through misuse of the
meter.
You should keep battery power applied to your sensors at all times.
The following guidelines will help prevent damage to your sensors:
Always store your unit in a place where the temperature does not get
down to or below freezing.
Always maintain battery power to the sensors. When the batteries get
low replace them as soon as possible.
Never allow foreign objects or material to enter the sensor holes, dam-
age to the sensor may result.
Never over saturate your sensors by performing tests on equipment
with gas levels beyond the capability of you analyzer.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
General Overview (Continued)
This manual will guide you through the functions of the TPI 1010a
which will give you many years of reliable service.
Your TPI 1010a Indoor Air Quality meter comes complete with the
following standard accessories:
•TPI 1010a Instrument
•Protective Rubber Boot (A800)
•Soft Carrying Case (A921)
•USB Cable & Software (A803)
•Instruction Manual
Your TPI 1010a Indoor Air Quality meter has the following optional
accessories available:
•Power adapter / Battery eliminator (A804)
•Infrared Printer (A740)
•Magnetic strap kit to hang meter (A127)
•Boot hook to hang meter (A103)
•Replacement Software only (A802)
•Replacement USB cable only (A801)
( ) Denotes part number
A804 Battery Eliminator Specifications:
Input: 100 ~ 240VAC @ 47 ~ 63Hz
Output: 5VDC @ 2A
Center pin positive
Fitted with two pin European style plug. Comes with USA pin adapter.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
3. Front View
Sensor Locations: Places where the CO, CO2, and Humidity sensors
are located and protected.
Display : Large 4 Parameter Backlit LCD Display.
Protective Rubber Boot: Provides protection to meter housing.
Keypad: Selects all available functions
USB Port Location for connection of USB cable for PC communication.
Power Adapter Socket: Location to connect optional power adapter.
Infrared Window: Used to print test results to optional infrared printer.
Humidity &
Temperature
Sensor Location
Display
Keypad
CO2 Sensor
Location
CO Sensor
Location
USB Port Power Adapter
Protective
Rubber Boot
Infrared Window
for Printing Test
Results
(Requires optional A740
printer)
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
3.1 Soft Keys
On / Off key - Used to turn the IAQ meter on or off. Press to turn on,
press and hold to turn off.
Up Arrow key - Used to select and change parameters. Also used to
cycle through dew point and wet bulb temperatures from the main
display.
Left Arrow key - Used to select and change parameters.
Right Arrow key - Used to select and change parameters.
Down Arrow key - Used to select and change parameters.
Enter key - Used to activate % outside air mode. Also used to accept
parameter changes.
Mode key - Used to activate and deactivate data logging mode. Press
and hold to activate or deactivate logging.
Backlight key - Used to turn the display backlight on and off.
T/C key - Used to switch the bottom display between temperature /
humidity and time display modes. Also used to perform ambient air
CO2 reset.
Unit key - Used switch the bottom temperature display between
Fahrenheit and Celsius modes.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
3.2 Back View
Tilt Stand
Battery Cover Screw
Hanger Hole
Hanger Hole: Use to hang instrument for hands free operation. Can
be used with A127 magnetic strap kit or A103 hook.
Tilt Stand: Use to stand instrument on a table.
Batter Cover Loosen this screw and open cover to access batteries.
Screw:
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
4. Operation
4.1 Turning On & Off / Performing a Test / Main Display
Always: - Turn the 1010a on outside of the area to be tested. Make sure the
unit is in fresh air (no carbon monoxide present) prior to turning on. This will
allow the CO sensor to set to zero properly.
Carbon dioxide (CO2) in parts per million (ppm) is displayed at the top, car-
bon monoxide (CO) in parts per million (ppm) is displayed in the middle,
temperature in °F or °C (selectable), and humidity in percent are displayed at
the bottom of the main display.
The battery indicator is located at the bottom left of the display. When the
batteries become low they must be replaced to maintain proper operation.
If 30ppm or more CO is measured the 1010a will beep and the display will
flash red as a warning. This alarm point is adjustable. Additional functions
can be activated during testing. Please see next sections.
Carbon dioxide (CO2)
Carbon monoxide (CO)
Temperature
Humidity
Battery indicator
Press the key and the 1010a will begin a 30 second countdown. During
this time the 1010a performs a self diagnostic and sets the CO sensor to zero.
Once the countdown ends the 1010a will display CO2, CO, Temperature, and
Humidity. NOTE: If the CO2 sensor seems to read out of specification perform
the Ambient CO2 Sensor Reset as described in section 4.9.
Enter the area to be tested, the measured values will be displayed.
To turn the 1010a off, press and hold the key down until the 1010a turns
off.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
4.2 Selecting Temperature Units
4.3 Ambient / Dew Point / Wet Bulb Temperature Display
4.4 Temperature / Clock Display Modes
4.5 Activating the Backlight
4.6 Printing Measurements (Requires A740 Printer)
Ambient Temperature Dew Point Temperature
Indicated by “DP” in the
display
Wet Bulb Temperature
Indicated by “WB” in
the display
Repeatedly pressing the key from the main display cycles through dew
point temperature, wet bulb temperature, and ambient temperature displays.
Pressing the key switches the temperature display between °F and °C.
Pressing the key from the main display cycles between temperature
and clock display. To set the clock please refer to section 4.6.
Pressing the key turns the display backlight on and off. Power
consumption is much higher when the backlight is activated. The backlight
will automatically turn off 30 seconds after it is activated. To conserve bat-
tery life the backlight should only be used when necessary.
Align the infrared window of the A740 printer with the infrared window of
the 1010a located on the upper right side of the meter. Keep the printer in
clear line of sight approximately 6 to 8 inches away from the 1010a. Press
and hold the key for approximately 2 to 3 seconds and the 1010a will
send test data to the printer.
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
1) Starting with the 1010a turned off, press and hold down the
2) Using the Arrow keys, set the year. Once the year is set, press
3) Using the Arrow keys, set the month. Once the month is set, press
4) Using the Arrow keys, set the day. Once the day is set, press
5) Using the Arrow keys, set the hour. Once the hour is set press
6) Using the Arrow keys set the minutes. Once minutes is set, press
The 1010a will return to normal operation.
key then
press and hold down the key until two beeps are heard and the time / date
screen is displayed.
Year
Month / Day
Hour / Minutes
(24 hour clock, HH:MM)
4.7 Setting Date and Time
www.GlobalTestSupply.com
Find Quality Products Online at: sales@GlobalTestSupply.com
Indice
Altri manuali TPI Strumento di misura
