Tranberg TEF 4600 Manuale utente

R. Stahl Tranberg AS

E[email protected] | stahl-tranberg.com

Main ofﬁce: Strandsvingen 6 | N-4032 Stavanger | Norway | T+47 51 57 89 00 | F+47 51 57 89 50

Ofﬁce Oslo: Luhrtoppen 2 | N-1470 Lørenskog |Norway | T+47 24 08 44 10

IMPORTANT

Read this instruction carefully before installing the

product

The information contained in this document remains

the sole property of Tranberg AS. No part of this

document may be copied or reproduced in any form

or by any means, and the information contained

within it is not to be communicated to a third party,

without the prior written consent of Tranberg AS.

The document, or any part of it, may not be

translated to any other language without the written

approval from Tranberg AS.

DISCLAIMER

Tranberg AS endeavors to ensure that all informa-

tion in this document is correct and fairly stated, but

does not accept liability for any errors or omissions.

CONTROL SYSTEM

TEF 4600

HELIDECK LIGHT CONTROL

SAFE AREA

USER MANUAL

Subject to change without prior notice TUM6482

Page 2

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

TABLE OF CONTENTSNTS:

1. INTRODUCTION 3

2. APPLICATIONS 3

3 CONTENT IN BOX 3

4 SAFETY PRECAUTIONS 3

5 ABOUT THE SYSTEM 3

6 TERMINAL CONNECTIONS 3

7.1 CONFIGURATION STATUS LIGHTS 3

7.1.1 Enable Installed Lights 3

7.1.2 Status Light Automatic Test: 3

7.1.3 Status Light On Timeout 3

7.1.4 Status Light Dim Timeout 3

7.1.5 Helideck Lights Timeout 3

7.2 CONFIGURATION CIRCLE & H 4

7.2.1 Adjustment of the «BRIGHT» light level 4

7.2.2 On site Control 4

8 COMMISSIONING 4

9 DISPOSAL 4

10 OPERATION 5

10.1 Control Screen 5

10.2 Status Light Screen 6

10.2.1 Suppress 6

10.2.2 Activate (Manual activation) 7

10.2.3 Dim 7

10.2.4 Activation Timeout 7

10.2.5 Dim Timeout 7

10.2.6 Inspection Interval 7

10.2.7 Status light Fault indicators 7

10.3 Setup screen, page 1 8

10.3.1 Activate Modbus TCP 8

10.3.2 Choose language 8

10.3 Setup screen, page 2 9

10.3.3 Internal Horn Audible Alarm. 9

10.3.4 Helideck Lights Timeout 9

10.3 Setup screen, page 3 10

10.3.5 Local Remote Mode Enable 10

10.3.6 Panel is local 10

10.3.7 Panel is remote 10

10.3 Setup screen, page 4 11

10.3.8 Enable lights for function 11

10.4 Alarms Screen 12

11 GA DRAWING 13

Page 3

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

1. INTRODUCTION

Thank you for purchasing this product!

For installation, maintenance and assurance of a long

life of this product, please follow this manual.

For more detailed mounting instructions on the Rittal en-

closure please see user manual TUM5915.

For more detailed mounting instructions on the Rittal

Sockel-System-Flex please see user manual TUM5916.

2. APPLICATIONS

Control system for Tranberg TEF 4600 Helideck Light

Control.

Status lights: Up to 2 main lights and 2 repeater lights.

Floodlights: Up to 2 Floodlight circuits.

Perimeter lights: Up to 2 Perimeter lights circuits.

Obstruction light: One Obstruction light circuit.

Windsock: One Windsock circuit.

Circle & H: One Circle & H circuit.

Auxiliary: Two Auxiliary light circuits.

3 CONTENT IN BOX

• 1 pc control cabinet

• 1 Pack of Resistors for conﬁguration of C&H

• Flex-Block Trim Panels

4 SAFETY PRECAUTIONS

Note that changes made to the product and/or instal-

lation of components which do not conform to the ap-

proval, may be a safety violation. The manufacturer will

in no circumstance be held responsible for such activity.

For your health and safety, always use safety gear suited

for the task. Be certain to follow codes, regulations and/

or speciﬁc procedures that are related to the installation.

The TEF 4600 control cabinet shall be stored in a dry

place. Storage temperature range (non-condensing):

-10°C to +55°C

5 ABOUT THE SYSTEM

The standard control system consists of a control cabinet

with power supply, PLC, circuit breakers, terminal blocks.

It’s possible to connect several remote control panels as

well as connect the sys¬tem to a remote SCADA-system.

Connect SCADA system to the general alarm output NO/

NC volt free contact to retrieve instant notiﬁcation in case

anything should fail.

6 TERMINAL CONNECTIONS

Terminal connections overview

-X1: 230 VAC Supply

-X2: Helideck light 230V Outputs

-X3: 24VDC Remote Signals

-X4: External alarm Interface

-X5: Status Lights

-X6: C&H Lights

7.1 CONFIGURATION STATUS LIGHTS

7.1.1 Enable Installed Lights

The left side has enable function for each Helideck light

module. The Helideck light modules that are present on a

given vessel or installation shall be set to Enable for con-

trol and monitoring of said light. The Button will be green

when Enabled.

7.1.2 Status Light Automatic Test:

This Function will enable or disable Automatic test of

the Status Lights. When enabled the Status Lights will

perform a self check once per 24 hours. The test is per-

formed by the lamps being turned on for 1 second at very

low light intensity. This test will serve as a early warning

diagnostics. If alarm is present the lamp will report this to

the Control System and an Alarm with descriptive text will

be shown in the Alarms screen.

7.1.3 Status Light On Timeout

Activation timeout will deactivate the Status light system

when the timer has elapsed. Default value is 30 minutes.

The Button will be green when Enabled.

7.1.4 Status Light Dim Timeout

Dim timeout will deactivate the dimming function when

the timer has elapsed. Default value is 30 minutes. The

Button will be green when Enabled.

7.1.5 Helideck Lights Timeout

Helideck Lights Timeout will deactivate the «All Helideck

Lights On» function when the timer has elapsed. The But-

ton will be green when Enabled.

Page 4

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

9 DISPOSAL

Disposal

Dispose of according to company regulations and

na¬tional rules. The equipment is recycled/disposed of

as electrical equipment.

8 COMMISSIONING

After conﬁguration, all conﬁgured features, as well as the

Fire and gas input and the overall function of the system

should be tested. SEE COMMISSIONING PROCEDURE

TTD 5909.

7.2 CONFIGURATION CIRCLE & H

7.2.1 Adjustment of the «BRIGHT» light level

The “bright” light level can be adjusted up to twice the

intensity speciﬁcation of “standard” level. The purpose of

this facility is to ensure adequate performance at installa-

tions with high levels of background lighting without risk-

ing glare at less well-lit installations. To adjust light level,

replace resistor plugs in accordance with table below.

7.2.2 On site Control

Once installed and with reference to the Installation Man-

ual (TUM6332), make sure that the system functionality is

as per the Installation Manual and speciﬁcations:

• Check the local on/off control

• Check the local standard/bright control:

the adjustment of the “BRIGHT” light level must be

checked against the intensity of the perimeter lights

(brightest of the three). The Circle lights must not be

brighter than the perimeter lights and H lights not

brighter than the Circle lights.

• Check that the remote control repeats the system

functionality as for the control cabinet (as relevant) by

performing the same tests.

Page 5

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

10 OPERATION

10.1 Control Screen

The Control Screen contains control and monitoring of

Helideck lights. Each button controls one light circuit.

The circuits are toggled on and off by pressing and hold-

ing the button for 1 second.

From the Setup page, the circuits that are in use should

be selected. Only the selected circuits will show in the

Control screen.

Each button has four modes to represent circuit status:

Green: Circuit is on.

Grey: Circuit is off.

Red: Circuit is on with error.

Yellow: Circuit is off with error.

The available lights to control are:

Helideck lights: Turn on/off all Helideck lights. (Flood-

lights Dim and Circle & H and Status lights not included.)

Floodlight 1: Turn on/off Flood light circuit 1.

Floodlight 2 Turn on/off Flood light circuit 2.

Floodlight Dim: Activate standard/dim

brightness of Floodlight circuits.

Perimeter light 1: Turn on/off Perimeter light

circuit 1.

Perimeter light 2: Turn on/off Perimeter light

circuit 2.

Circle & H: Turn on/off Circle & H circuit.

Circle & H Bright: Activate standard/bright

brightness of Circle & H circuits.

Windsock: Turn on/off Windsock

circuit.

Obstruction light: Turn on/off Obstruction light

circuit.

Auxiliary light 1: Turn on/off Auxiliary light 1

circuit.

Auxiliary light 2: Turn on/off Auxiliary light 2

circuit.

Page 6

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

10.2 Status Light Screen

The Status light screen contains control and monitoring

of the Status light system.

10.2.1 Suppress

The Suppress function is activated/deactivated by

pressing and holding the Suppress button for 4 seconds.

When suppressed the Status lights will not activate by

manual activation nor external Fire & Gas signal. Dim

function is also disabled in this mode.

Activate and Dim are reset when Suppress mode is ac-

tivated. External Fire & Gas signal is suppressed until

Suppress mode is deactivated.

When Suppress mode is activated, the following indica-

tion lights will blink at 1Hz interval: Activate button, Dim

Button, Main Light 1 lamp, Main light 2 fault lamp, Re-

peater light 1 fault lamp and Repeater light 2 fault lamp.

Page 7

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

10.2.2 Activate (Manual activation)

The Activate function is activated/deactivated by press-

ing and holding the Activate button for 2 seconds.

Manual activation of Status lights will keep the Status

lights activate until:

• Manual deactivation.

• Suppress mode activation.

• Activate is not possible if the system is Suppressed or

if external Fire & Gas signal has activated the system.

10.2.3 Dim

The Dim function is activated/deactivated by pressing

and holding the Dim button for 2 seconds.

Dim of Status lights will keep the Status lights dimmed

until:

• Dim Timeout speciﬁed time has elapsed. (only

applicable if Dim Timeout is enabled in the Setup

screen.)

• Suppress mode activation.

• Dim mode deactivation.

• Manual Activation.

• Dim is not possible if the system is Suppressed.

10.2.4 Activation Timeout

Activation timeout will deactivate the Status light system

when the timer has elapsed. Default value is 30 minutes.

The Activation timeout is enabled in the Setup screen.

10.2.5 Dim Timeout

Dim timeout will deactivate the dimming function when

the timer has elapsed. Default value is 30 minutes. The

Dim timeout is enabled in the Setup screen.

10.2.6 Inspection Interval

Inspection interval is a time span of days which, when

counted down, will trigger an Inspection Required indi-

cator in the Status Light screen. The Operator can man-

ually enter the number of days for Inspection required

prompt. To reset the inspection timer the operator needs

to press the Inspection Reset button.

10.2.7 Status light Fault indicators

There are ﬁver Status Light fault indicators:

• Main Light 1 Fault: Blinking indicates light is

connected but error is present. Steady light indicates

Light is disconnected.

• Main Light 2 Fault: Blinking indicates light is

connected but error is present. Steady light indicates

Light is disconnected.

• Repeater Light 1 Fault: Blinking indicates light is

connected but error is present. Steady light indicates

Light is disconnected.

• Repeater Light 2 Fault: Blinking indicates light is

connected but error is present. Steady light indicates

Light is disconnected.

• MCB Fault: Steady light indicates error is present on

24VDC Power Supply distribution circuit breaker.

Page 8

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

10.3 Setup screen, page 1

10.3.1 Activate Modbus TCP

If Modbus TCP is used for control and monitoring with

external control system this function is activated here.

For new connection, disable Modbus, enter IP-address

of Client, and ﬁnally enable Modbus again.

10.3.2 Choose language

These are the languages which can be chosen for this

application.

Page 9

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

10.3.3 Internal Horn Audible Alarm.

This function will enable/disable the internal buzzer of

the HMI touch panel. When enabled the buzzer will acti-

vate when an alarm is present.

10.3.4 Helideck Lights Timeout

Helideck Lights Timeout will deactivate the «All Helideck

Lights On» function when the timer has elapsed. The

Button will be green when Enabled.

10.3 Setup screen, page 2

Page 10

TEF 4600 CONTROL SYSTEM - INSTALLATION AND USER MANUAL

10.3.5 Local Remote Mode Enable

If there are two touch panels or one touch panel and

onePC running the HMI application there is the option

to use Local/Remote mode. When activated the Local

or Remote panel must use the “Take Control” button to

control the Helideck lights. When not in control a panel

will only be able to monitor the status of the Helideck

lights. If the remote panel does not have control and an

attempt is made to turn on a light circuit “Take Control”

button will display the following text: “ Local panel has

control”.

10.3.6 Panel is local

Enable this if the Panel is local.

10.3.7 Panel is remote

Enable this if the Panel is remote.

10.3 Setup screen, page 3

Indice

Altri manuali Tranberg Sistema di controllo

Tranberg

Tranberg TEF 4900 Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente