TRENDnet TEW-410APB Manuale utente
English
TEW-410APB
Wireless 802.11g AP
Quick Installation Guide
Version 1.4
0
General Wireless AP System Connection
Below is the general function of Wireless AP diagram.
Plug in the power supply. The power LED will turn on to indicate power
operation.
User may connect the AP’s LAN ports to switch/hub if there are wired
computers that also need to link Intranet or Internet. The Wireless
Interface can easily manage 30 wireless clients workstation
simultaneously.
1
AP Default Settings
The default settings are shown following.
User admin
Password admin
AP IP Address 192.168.1.250
AP Subnet Mask
255.255.255.0
RF ESSID ap11g
11g RF Channel 6
Mode 11b+g
Encryption Disabled
Configure your Network Adapter’s IP Address
To configure this Access Point (AP), please connect the unit to wired Ethernet
network (make sure the IP address 192.168.1.250 is not already in use) and
use a computer on the network to configure the AP. Or, connect (network) a
Computer with Ethernet adapter to the AP and then configure the AP. In either
case, please change the computer’s network adapter’s IP address to
192.168.1.X (where X = any number from 1 ~ 249) with subnet mask
255.255.255.0, and then use this computer to configure the AP.
To configure the network adapter’s IP address, please go to “Network
Properties” (or “Local Area Connection” properties) and then go to “TCP/IP”
properties.
2
Step1
START UP & LOGIN
In order to configure the Wireless 11g AP, you must use your web browser
and manually input http://192.168.1.250 into the Address box and press Enter.
The Main Page will appear.
To start configure the Wireless 11g AP, you must login as “admin” in the
User Name box. And input password “admin” on the password section.
Once you have logged-in as administrator, it is a good idea to change the
administrator password to ensure a secure protection to the Wireless 11g AP.
The Security Settings section described later in this manual describes how to
change the password.
Once you have input the correct password and logged-in, the screen will
change to the Setup page screen.
TURN ON POWER SUPPLY
Quick power cycle can caused system corruption. When power on,
be careful not to
shut down in about 5 seconds, because data is writing to the flash.
3
Step2
This screen contains all of the AP's basic setup functions.
Most users will be able to configure the AP and get it working properly using
the settings on this screen.
LAN IP Address and Subnet Mask: This is the AP's IP Address and Subnet
Mask as seen on the internal LAN. The default value is 192.168.1.250 for IP
Address and 255.255.255.0 for Subnet Mask.
Please Click “Apply” button to save your settings once you have any change.
MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER
To change the configuration, use Internet Explorer (IE) or Netscape Communicator
to connect the WEB management 192.168.1.250.
4
Wireless: This section provides the Wireless Network settings for your WLAN.
Wireless Settings
5
SSID: The service set identifier ( SSID ) or network name. It is case sensitive
and must not exceed 32 characters, which may be any keyboard character.
You shall have selected the same SSID for all the APs that will be
communicating with mobile wireless stations.
Channel: Select the appropriate channel from the list provided to correspond
with your network settings. You shall assign a different channel for each AP to
avoid signal interference.
Security: To enable WEP (Wired Equivalent Privacy) or WPA (Wi-Fi
Protected Access), please click on “Enable” and then click on “Configure
Security”.
Security Mode: Options are WEP, WPA Pre-Shared Key, and WPA RADIUS.
In this guide we will cover WEP setup, for WPA, please refer to the User’s
Guide on the CD-ROM.
WEP: Make sure that all wireless devices on your network are using the same
encryption level and key. WEP keys must consist of the letters "A" through "F"
and the numbers "0" through "9."
Please Click “Apply” button to save your settings once you have any change.
6
Important Notice
In order to make right use of WPA, please ensure that your current Wireless Adapter’
s driver, and
Wireless Utility can support it, WPA needs 802.1x authentication (when RADIUS mode is chosen),
though the Operating System must also support 802.1x protocol. For Microsoft’s OS family,
only
Windows XP has incorporated this by default. The rest of the OS must installed 3er party’
s client
Technical Support
You can find the most recent software and user documentation on the
TRENDware website. TRENDware provides free tech
nical support for
all customers for the duration of the warranty period on this product.
TRENDware Technical Support
Tel: +1-310-891-1100
Fax: +1-310-891-1111
E-mail: support@trendware.com
www.trendware.com
Support Hours: 7:30AM ~ 6:00PM,
Mon. ~ Fri. (except holidays)
7
8
Deutsch
TEW-410APB
Wireless 802.11g AP
Kurzinstallationsanleitung
Version 1.4
Altri manuali per TEW-410APB
2
Indice
Lingue:
Altri manuali TRENDnet Punto di accesso wireless
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point Manuale utente
TRENDnet
TRENDnet 14dBi Manuale utente
TRENDnet
TRENDnet TEW-212APBO Manuale utente
TRENDnet
TRENDnet TEW-755AP Manuale utente
TRENDnet
TRENDnet P600 Manuale utente
TRENDnet
TRENDnet TEW-753DAP Manuale utente
TRENDnet
TRENDnet TEW-670AP Manuale utente
TRENDnet
TRENDnet TEW-823DAP V2 Manuale utente
TRENDnet
TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... Manuale utente
TRENDnet
TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... Manuale utente
TRENDnet
TRENDnet TEW-310APBX Manuale utente
TRENDnet
TRENDnet TEW-310APB Manuale del proprietario
TRENDnet
TRENDnet TEW-650AP Manuale utente
TRENDnet
TRENDnet TEW-825DAP Manuale utente
TRENDnet
TRENDnet TEW-411BRPplus Manuale utente
TRENDnet
TRENDnet TEW-753DAP Manuale utente
TRENDnet
TRENDnet TEW-826DAP Manuale utente
TRENDnet
TRENDnet TEW-610APB Manuale utente
TRENDnet
TRENDnet TEW-755AP Manuale utente
TRENDnet
TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... Manuale utente
