TRENDnet TEW-653AP Manuale utente
TEW-653AP
1.01
Quick Installation Guide
Table of Contents
English 1
1. Before You Start
2. Hardware Installation 2
3. Power-over-Ethnernet Installation 3
1
4. Configure the Access Point 5
5. Mounting 8
Troubleshooting 9
Version 11.16.2009
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
1. Before You Start
Package Contents
Note:
The TEW-653AP only works with Power over Ethernet (PoE) devices that follow the
IEEE 802.3af standard.
System Requirements
?Web Browser: Internet Explorer (6.0 or higher)
?A computer with a network adapter properly installed.
?A network Switch or Hub with an available network LAN port.
?Power over Ethernet (PoE) Switch (e.g. TPE-80WS) (Optional)
?Injector (e.g TPE-111GI ) (Optional)
1
?
?Multi-Language Quick Installation Guide
?CD-ROM User’s Guide
?Cat. 5 Ethernet Cable (1m / 3.3ft.)
?Power Adapter (12V DC, 1A)
?Mounting Kit
TEW-653AP
( )
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
2. Hardware Installation
2
Note: Locate an optimum location for the Access Point. The best place for the Access
Point is usually at the center of your wireless network. Please connect the computer
configuring the TEW-653AP to the same switch/hub.
1. Run a RJ-45 cable and the power adapter
through the cable clip on the TEW-653AP.
3. Connect the Power Adapter to the Access Point
and then to a power outlet.
2. Connect the RJ-45 cable from the Switch/Hub
to the LAN port on the Access Point.
4. Verify that the wireless, LAN and power LEDs
are on.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
2. Verify that the wireless, LAN and power LEDs
are on. Please refer to step 4 in the Hardware
Installation section.
3
3. Power-over-Ethernet Installation
Using the TEW-653AP with a PoE switch
1. Connect a RJ-45 cable from the Power-Over-
Ethernet Switch (e.g. TRENDnet TPE-80WS) to
the LAN port on the Access Point.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
4
Using the TEW-653AP with the TPE-111GI
1. Connect the Power Cord to the Power
Adapter.
2. Connect the Power Adapter to the DC 48V IN
connector on the TPE-111GI. Then connect
the Power Cord to an outlet.
4. Connect a CAT-5 cable from the TEW-653AP's
LAN port to the TPE-111GI's PoE Out port.
3. Connect a CAT-5 cable from a switch to the
TPE-111GI's DATA IN port.
5. Verify that the wireless, LAN and power LEDs
are on. Please refer to step 4 in the Hardware
Installation section.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
5
4. Configure the Access Point
Note: It is recommended that you configure the Access Point from a wired computer.
Before the Access Point can be configured, a Static IP address must be assigned to
your computer's network adapter in the subnet of 192.168.10.X. Since the Access
Point's default IP address is 192.168.10.100, make sure no other network devices are
assigned an IP address of 192.168.10.100. (Refer to Troubleshooting section on how to
configure TCP/IP settings on your PC.)
1. Open your web browser, type
http://192.168.10.100 in the Address bar, and
then press Enter.
2. Enter the User name and Password, and then
click OK. By default:
User Name: admin
Password: admin
3. Click Wizard.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
6
Note:
1. To protect your network from any unauthorized access it is recommended to enable
wireless encryption.
2. The examples below are for WPA2-PSK security. If you select WPA-PSK or
WPA2-PSK, make sure your wireless adapters support WPA or WPA2. If your
wireless adapters do not support WPA or WPA2, then select WEP.
4. Click Next.
5. Select AP Mode and then click Next.
6. Use your mouse to select the desired security
level (lowest for no encryption, highest for
WPA2-PSK).
7. Enter the desired SSID and Key. Then click
Next. By default, the SSID is TRENDnet653.
8. Setup is successful. Click Reboot.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
7
9. Wait 24 seconds while the Access Point
reboots.
Your configuration is complete
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
For detailed information regarding the TEW-653AP’s configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide CD-ROM, or TRENDnet's website
at http://www.trendnet.com.
10. Click System -> LAN. Configure the LAN
settings to match your network settings and
then click Apply.
11. Wait 14 seconds while the Access Point
reboots.
ENGLISHFRANÇAISDEUTSCHESPAÑOL
ÐÓÑÑÊÈÉ
8
1. Use the mounting plate as a template and mark
the wall for the correct screw position.
2. Drill holes for the screws at the marked
positions on the wall.
5. Mounting
3. Use the provided wood screws to secure the
mounting plate to the wall.
5. Follow the arrow to secure the TEW-653AP to
the mounting plate.
4. Align the TEW-653AP with the mounting plate
Altri manuali per TEW-653AP
2
Indice
Altri manuali TRENDnet Punto di accesso wireless
TRENDnet
TRENDnet TEW-638APB Manuale utente
TRENDnet
TRENDnet TEW-638PAP Manuale utente
TRENDnet
TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... Manuale utente
TRENDnet
TRENDnet TEW-430APB - Wireless Access Point Manuale utente
TRENDnet
TRENDnet TEW-740APBO Manuale utente
TRENDnet
TRENDnet TEW-690AP Manuale utente
TRENDnet
TRENDnet TPL-210AP Manuale utente
TRENDnet
TRENDnet TEW-434APB - 54Mbps Wireless G PoE Access... Manuale utente
TRENDnet
TRENDnet TEW-435BRM - 54MBPS 802.11G Adsl Firewall M Manuale utente
TRENDnet
TRENDnet TEW-738APBO Manuale utente
TRENDnet
TRENDnet TEW-410APB Manuale utente
TRENDnet
TRENDnet TEW-413APBO Manuale utente
TRENDnet
TRENDnet TEW-AP100plus Manuale utente
TRENDnet
TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... Manuale utente
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point Manuale utente
TRENDnet
TRENDnet TEW-AP100plus Manuale utente
TRENDnet
TRENDnet TEW-820AP Manuale utente
TRENDnet
TRENDnet TEW-410APBplus Manuale utente
TRENDnet
TRENDnet 14dBi Manuale utente
TRENDnet
TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... Manuale utente
