TRENDnet TEW-738APBO Manuale utente

TREflDnET

10 dBi Outdoor PoE Access Point

TEW-738APBO

• Quick Installation Guide (1)

TEW-738AP O (V1 ] / 04.23.2014

ESPANOL I DEUTSCH FRAN^AiS ENGLISH

1. Before You Start

Package Contents

• TEW-738AP O

• CD-ROM (User's Guide)

• Multi-Language Quick Installation Guide

• Proprietary PoE injector

• Power adapter (48 V DC, 0.5 A)

• Mounting Hardware

• Waterproof RJ-45 plug (network cable is not included)

• Grounding wire

Installation Re uirements

• Computer with a network port and web browser

• A network switch or router with an available network LAN port

• 2 x RJ-45 network cables (sold separately)

• Phillips screwdriver (sold separately)

Note:

• The TEW-738AP O does not support IEEE 802.3af. You must use the proprietary Power over

Ethernet injector that is supplied with the TEW-738AP O.

2. Point-to-Point WDS Installation

Note:

The default IP address of the TEW-738AP O is 192.168.10.100. To configure the

TEW-738AP O, your network adapter must have an IP address within the 192.168.10.x subnet

(e.g. 192.168.10.50). Please refer to the Appendix in the User's Guide for more information.

Phase 1: Overview

Note:

• The initial configuration should be completed in a testing environment with two

TEW-738AP O's approximately 15 ft. (5 meters) apart from one another.

• Configure and connect the devices before mounting.

1. Write the MAC address (MAC1) of the two TEW-738AP Os. The MAC address (MAC1) can

be found on the side of the unit. In this example, we will assume the following:

TEW-738AP O #1 MAC Address:00:11:22:00:00:11

TEW-738AP O #2 MAC Address:00:11:22:00:11:22

2. Power on the outdoor access point.

3. Login to the browser configuration page.

4. Change the administrator password.

5. Assign a valid IP address to the access point within the subnet defined by the router. Avoid

using an IP address within the DHCP pool of your router. In this example, we will assume the

following:

Router IP Address: 192.168.10.1

Subnet Mask: 255.255.255.0

DHCP Pool: 192.168.10.100~192.168.10.149

DEUTSCH 1 FRA^$A»S ENGLISH

ESPANOL I DEUTSCH FRAN£AiS ENGLISH

The TEW-738AP O will be setup with the following IP address assignment:

TEW-738AP O #1

IP Address: 192.168.10.50

IP Netmask (Subnet Mask): 255.255.255.0

IP Gateway (Gateway IP Address): 192.168.10.1

Primary DNS: 192.168.10.1

TEW-738AP O #2

IP Address: 192.168.10.51

Subnet Mask: 255.255.255.0

Gateway IP Address: 192.168.10.1

Primary DNS: 192.168.10.1

6. Enable WDS mode.

7. Enable WPA2-PSK AES encryption and configure a wireless password for the access point.

8. Enter the MAC address of the other outdoor access point.

9. Repeat the process for the second outdoor access point.

10. Confirm connectivity between the two access points.

Phase 2: WDS Setup

Note:

• The initial configuration should be completed in a testing environment with two

TEW-738AP O's approximately 15 ft. (5 meters) apart from one another.

• Configure and connect the devices before mounting.

©L

1. Connect one end of a network cable into TEW-738AP O #1.

2. Connect the opposite end of the network cable to the P+DATA OUT port on the Power over

Ethernet Injector.

3. Connect one end of another network cable to the 10/100 DATA IN port on the Power over

Ethernet Injector.

4. Connect the other end of a network cable to your computer's Ethernet port.

5. Connect the power adapter into the Power over Ethernet Injector. Then connect the power

adapter into a power outlet. (EU models have an on/off switch. Please move the power switch to

the “On” position.).

6. Assign a Static IP address to your computer's network adapter in the subnet of 192.168.10.x

(e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.

7. Open your web browser, type the IP address of the access point in the address bar, and then

press Enter. The default IP address is 192.168.10.100

8. Enter the User name and Password, and then click OK. y default:

User Name: admin

Password: admin

Note: Username and password are case sensitive.

Note: For first time installation, you are required to change the admin password.

9. Enter a new admin password.

DEUTSCH FRAM£ASS ENGLISH

PYCCKMfl ESPAiOL I DEUTSCH FRANQAiS | ENGLISH

10. Confirm the new password.

11. Click Save.

12. Please wait while the access point

reboots.

S stem is restarting,

please wait for 44

seconds

13. Enter the username and the new

password, and then click OK.

14. Click System " LAN.

15. Select Static IP.

16. Configure the IP address, IP Netmask

and IP Gateway based on the example in

Phase 1: Overview.

17. Select Specify DNS Server IP.

18. Configure the Primary DNS based on the

example in Phase 1: Overview.

19. Click Save.

20. Click System " Operating Mode.

21. Select WDS Mode and then click Save &

Reboot.

22. Please wait while the access point

reboots.

S stem is restarting,

please wait for 50

seconds

23. Enter the username and password, and

then click OK.

24. Click Wireless " WDS.

Note: To protect your network from any

unauthorized access it is recommended to

enable wireless encryption.

25. Enter the MAC address of the other access point. The below configuration will be based on

the example in Phase 1: Overview.

26. Click Reboot.

Press "Reboot" after all

configurations to enable ne

setting.

27. Click Reboot

28. Repeat steps 2-27 for TEW-738AP O #2.

Phase 3: Confirm Connectivity

1. Leave TEW-738AP O #2 connected to your computer.

2. Connect TEW-738AP O #1 to a LAN port of a router on your network.

3. To verify connectivity, run your computer's command prompt and ping TEW-738AP O #1's

assigned IP address from your computer.

4. A successful ping reply determines that both TEW-738AP Os are configured properly and

connected.

ESPA&OL I DEUTSCH FRAN£AiS ENGLISH

PYCCSCMM 1 ESPAfcL I DEUTSCH FRANQAIS ENGLISH

3. Hardware Installation

Waterproof kit installation

1. Unscrew the sealing nut from the main

body.

2. Separate the rubber seal from the claw.

3. Verify that you have the following parts:

« } O S

Cable Gland Seal Claw Sealing Nut

4. Insert one end of an Ethernet cable into

the sealing nut.

5. Insert the Ethernet cable into the seal.

7. Insert the seal/rubber claw into the Cable

Gland.

8. Connect the Ethernet cable to the PoE port

on the rear of the TEW-738AP O.

9. Using your hand, screw the main body

counter clockwise to secure it to the

TEW-738AP O.

10. Using your hand, screw the seal nut

counter clockwise to secure it to the main

body.

Point-to-Point (WDS Bridge) Installation

TEW-738AP O #1 TEW-738AP O #2

uilding

ESPA&OL I DEUTSCH FRAN£AiS ENGLISH

P CCKMft E8PAN0L I DEUTSCH FRANQAIS ENGLISH

1. Refer to the above diagram.

2. Mount the TEW-738AP Os in your desired location. See Pole Mounting the TEW-738AP O

for mounting instructions.

3. Connect the TEW-738AP Os to their respective network.

4. Confirm that the TEW-738AP Os are facing each other.

5. Verify that the status LED indicators on both TEW-738AP Os are fully functional: PWR

[Power](Greeii / Solid), LAN ( linking / Green), Wireless Signal Strength ( linking /

Green).

Wireless Signal Strength

Connecting the Grounding Wire

1. Identify the grounding hole on the outdoor access point. You w

LAN

Power

l see a symbol next to the hole.

2. Align one end of the grounding wire over the hole. Then secure grounding wire with the

provided screw and washer.

3. Connect the green grounding wire to a grounding object.

e.g. Earth driven rod, grounded electrical system.

Altri manuali per TEW-738APBO

Indice

Altri manuali TRENDnet Punto di accesso wireless

TRENDnet

TRENDnet TEW-AP100plus Manuale utente

TRENDnet

TRENDnet TPL-210AP Manuale utente

TRENDnet

TRENDnet TEW-510APB Manuale utente

TRENDnet

TRENDnet WAP-200A Manuale utente

TRENDnet

TRENDnet TEW-510APB Manuale utente

TRENDnet

TRENDnet TEW-638AP Manuale utente

TRENDnet

TRENDnet TEW-814DAP Manuale utente

TRENDnet

TRENDnet TEW-690AP Manuale utente

TRENDnet

TRENDnet TEW-430APB - Wireless Access Point Manuale utente

TRENDnet

TRENDnet TEW-821DAP Manuale utente

TRENDnet

TRENDnet TEW-636APB Manuale utente

TRENDnet

TRENDnet TEW-412APBO Manuale utente

TRENDnet

TRENDnet TEW -739APBO Manuale utente

TRENDnet

TRENDnet TEW-638PAP Manuale utente

TRENDnet

TRENDnet TEW-670AP Manuale utente

TRENDnet

TRENDnet TEW-815DAP Manuale utente

TRENDnet

TRENDnet TEW-825DAP Manuale utente

TRENDnet

TRENDnet TEW-410APBplus Manuale utente

TRENDnet

TRENDnet TEW-AP100 Manuale utente

TRENDnet

TRENDnet TEW-690AP Manuale utente

TRENDnet

TRENDnet TEW-676APBO Manuale utente

TRENDnet

TRENDnet TEW-230APB Manuale utente

TRENDnet

TRENDnet TEW-410APBplus Manuale utente

TRENDnet

TRENDnet TEW-610APB Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente