TRENDnet TEW-510APB Manuale utente

TRENDnet

TRENDware, USA

What's Next in Networking

TEW-510APB

Version 05.19.2005

Super A+G Access Point Quick Installation Guide

Point d'accès Super A+G Guide d'installation rapide

Super A+G Access Point Kurzanleitung zur Installation

Punto de Acceso Súper A+G Guía de instalación rápida

Точка доступа Super A+G Руководство по быстрой установке

Table of Contents

English ......................................................................................................

Troubleshooting...........................................................................................

1. Prepare for Installation ......................................................................

2. Install Hardware ................................................................................

3. Configure TCP/IP Settings ................................................................

4. Configure the Access Point ...............................................................

Thank you for purchasing TRENDnet's TEW-510APB Super A+G Access Point

This guide will help you set-up your Access Point quickly and easily. Just follow

the step-by-step instructions below, and enjoy the benefits of accessing the

Internet without ever being tied down to wires! If you run into problems, please

refer to the Troubleshooting section. If you need further technical support,

please visit www.TRENDNET.com or call technical support by phone.

Verify Equipment

Before setting up the Access Point, you should have:

1. A Computer with a Wired (Rj45) or Wireless network card.

2. TCP/IP protocol installed on the Computer.

3. A Web Browser such as Internet Explorer (5.0 or higher) or

Netscape Navigator (4.7 or higher).

4. A Hub or Switch connecting your existing wired network.

5. An RJ-45 Network Cable for connecting the Access Point to your

network Switch.

Verify Package Contents

Please make sure you have everything in the box:

External Power Adapter 1.5M RJ45 cable

CD-ROM (User’s Guide)

Quick Installation Guide

TEW-510APB

1. Prepare for Installation

English QIG

English

TRENDnet

TRENDware, USA

What's Next in Networking

TEW-510APB

Version 05.19.2005

Super A+G Access Point Quick Installation Guide

Point d'accès Super A+G Guide d'installation rapide

Super A+G Access Point Kurzanleitung zur Installation

Punto de Acceso Súper A+G Guía de instalación rápida

Точка доступа Super A+G Руководство по быстрой установке

1. Locate an optimum location for the Access Point. The best place for the

Access Point is usually at the center of your wireless network.

2. Connect the RJ-45 network cable to the Access Point, then connect the

other end of the network cable to a Switch or Hub. The Access Point is now

connected to your 10/100Mbps network.

3. Connect the power adapter to the Access Point. Make sure you use the

power adapter supplied with the Access Point; using a different power

adapter may damage the unit.

2. Install Hardware

Check to make sure the following Access Point front panel lights are on: Power,

LAN, WLAN.

Verify Hardware Installation

NOTE: If you are using a wired computer to configure the Access Point,

please connect this computer to the same Switch or Hub the

TEW-510APB is connected to.

POWER LAN

WLAN

TEW-510APB

English

3. Configure TCP/IP Settings

Before the Access Point can be accessed and configured, the computer's

TCP/IP settings need to be changed. (That includes your wireless card's IP

address, too.)

English

Windows 2000/XP

1. Find the Start button located on the Desktop.

2. Click Start, and click on Control Panel. For Windows 2000, click Start,

highlight Settings, and click Control Panel.

3. Double-Click the Network Connection icon.

4. Right-Click on the Local Area Connection icon, then click on Properties.

The Local Area Connection Properties box will appear.

6. Click on Use the following IP address. Enter 192.168.1.50 for IP

address and 255.255.255.0 for Subnet, then click OK.

7. Click OK.

8. Your computer is now ready to access and configure the Access Point.

5. Under the General tab, locate and select Internet Protocol TCP/IP and

then click Properties. The Internet Protocol (TCP/IP) Properties box will

appear.

English

4. Configure the Access Point

From a Wired Computer

1. Open a web browser (Internet Explorer or Netscape) and enter

http://192.168.1.250 at the address bar, then press the Enter key. Leave the

username field blank, and type admin for your password.

If you are configuring the TEW-510APB through a wired computer, follow steps

1-3. If you are configuring the TEW-510APB through a wireless computer,

follow steps 4-7.

English

2. Click Wireless. Enter any AP Name for your Access Point. Create a SSID

that your wireless network will be using, and select a channel. (For example:

Wireless AP, Home AP, or Office AP). Scroll down to the bottom of the page

and click Apply.

3. Click Setup. If your current network belongs to a different network segment

(i.e. 192.168.0.1~254), please type an IP address, Subnet Mask, and a

Default Gateway (i.e. Router's IP Address). Click Apply. If you are content

with the TEW-510APB's current settings, please proceed to the next section.

English

From a Wireless Computer

(using TRENDnet's TEW-501PC as example in this section)

The default settings of the Access Point are:

SSID wlan-a

Channel - 6

4. On your wireless computer, open up your Wireless Utility Program.

5. Click AP List, select wlan-a, and click Connect.

7English

6. Click Link Information and verify that your wireless PC is communicating

with the TEW-510APB.

7. Go to the beginning of section 4. Configure the Access Point and follow

steps 1-3.

Troubleshooting

Q1:

A1:

Q2:

A2:

Q3.

A3:

Q4.

A4:

I specified the IP address http://192.168.1.100 in my internet

browser's address bar, but error message says "The page cannot be

displayed". How can I get into the TEW-510APB's web configuration

page?

Please check your hardware and TCP/IP settings again by following

the instructions sections 1~3, make sure the Power, WAN, WLAN on the

Access Point's front panel are on and the TCP/IP configurations are correct.

then try accessing http://192.168.1.100 again.

If my network's IP is different than the Access Point's range, what

should I do?

You should still configure the access point first. After all the settings

are applied, go to the Access Point's configuration page, click on TCP/IP

settings and change an IP address for the Access Point to match your

network's IP.

After I successfully configured the Access Point to meet my network

settings, I cannot connecting to my network using wireless computers.

If you have a DHCP server in your network, you need to go into TCP/IP

settings again and re-select "Obtain an IP automatically" for

Windows 98/ME and "Obtain an IP Address automatically" for Windows

2000/XP to allow the PC to regain an IP address from your DHCP server.

All the settings are set correct, but I still can't use the Access Point,

what should I do?

You can find additional information in the User's Guide. If you still have

Problems, contact our Technical Support by email or phone.

Certifications

This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received.

Including interference that may cause undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.

SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

Altri manuali per TEW-510APB

Altri manuali TRENDnet Punto di accesso wireless

TRENDnet

TRENDnet 12dBi Manuale utente

TRENDnet

TRENDnet TEW-510APB Manuale utente

TRENDnet

TRENDnet TEW-740APBO Manuale utente

TRENDnet

TRENDnet TEW-230APB Manuale utente

TRENDnet

TRENDnet TEW-430APB - Wireless Access Point Manuale utente

TRENDnet

TRENDnet TEW-410APB Manuale utente

TRENDnet

TRENDnet TEW-638APB Manuale utente

TRENDnet

TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... Manuale utente

TRENDnet

TRENDnet TEW-410APB Manuale utente

TRENDnet

TRENDnet TEW-638PAP Manuale utente

TRENDnet

TRENDnet TEW-413APBO Manuale utente

TRENDnet

TRENDnet TEW-735AP Manuale utente

TRENDnet

TRENDnet TEW-610APB Manuale utente

TRENDnet

TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... Manuale utente

TRENDnet

TRENDnet TEW-430APB - Wireless Access Point Manuale utente

TRENDnet

TRENDnet TEW-921DAP Manuale utente

TRENDnet

TRENDnet TEW-825DAP Manuale utente

TRENDnet

TRENDnet TEW-814DAP Manuale utente

TRENDnet

TRENDnet TEW-740APBO Manuale utente

TRENDnet

TRENDnet TEW-630APB - Wireless Access Point Manuale utente

TRENDnet

TRENDnet TEW-510APB Manuale di istruzioni

TRENDnet

TRENDnet TEW-230APB Manuale utente

TRENDnet

TRENDnet TEW-410APBplus Manuale utente

TRENDnet

TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente