TRENDnet TEW-740APBO2K Manuale utente

Quick Installation Guide

TEW-740APBO2K

Table of Content

1 English

1. Before You Start

2. Hardware Setup and Configuration

3. Ground Wire and Pole Mount Installation

ENGLISHFRANÇAISDEUTSCH

ESPAÑOLРORTUGUÊS

1. Before You Start

Note:

It is recommended to use network cables without additional caps, molded caps, or boots with

the access points for cable fitment inside the enclosure.

Note:

The TEW-740APBO does not support IEEE 802.3at/af PoE standards. You must use the

proprietary Power over Ethernet injector that is supplied with the TEW-740APBO. The RJ-45

Ethernet cable between the passive PoE injector and access point can have a maximum length

of up to 60 m (197 ft.).

Package Contents

Ÿ2 x TEW-740APBO

ŸCD-ROM (User's Guide)

ŸQuick Installation Guide

ŸProprietary PoE injectors

ŸPower adapters (12 V DC, 1A)

ŸMounting Hardware

ŸGrounding wires

Minimum Requirements

ŸComputer with a network port and web browser

ŸA network switch or router with an available network LAN port

ŸPhillips screwdriver (Ground wire installation)

Ÿ4 x RJ-45 network cables

2. Hardware Setup and Configuration

Note: By default, the TEW-740APBO access points are preconfigured to establish a point-to-

point WDS bridge between each other using a unique predefined AES encryption key. For

convenience, a unique predefined admin password has already been assigned to both access

points. You can find the preconfigured access point settings on the wireless sticker or on the

device label beneath the cover where the Ethernet ports and LEDs are located. No additional

configuration is required.

WIFI MAC: XXXXXXXXXXXXXXXXX

ETH LAN1 MAC: XXXXXXXXXXXXXXXXX

Model: TEW-740APBO / A

S/N: XXXXXXXXXXXXXXX

H/W: V2.0R FW: 2.0K

Made in XXXXXXX

IP Address: 192.168.10.50

Subnet Mask: 255.255.255.0

User Name: admin

Passwork: XXXXXXXX

Preset

Wireless Settings

Mode/WiFi Channel

WDS Bridge / CH 1

AES Encryption Key

Management Login

http://192.168.10.51

username: admin

password: XXXXXXXX

740XXXXXXXX

Unit 1 Unit 2

Preset

Wireless Settings

Mode/WiFi Channel

WDS Bridge / CH 1

AES Encryption Key

Management Login

http://192.168.10.50

username: admin

password: XXXXXXXX

740XXXXXXXX

ENGLISHFRANÇAISDEUTSCH

ESPAÑOLРORTUGUÊS

1. Remove the cover of the access point by pushing and holding the tab in the vertical direction

upward (based on the access point orientation below) and pulling the cover in the two

locations noted below away from the access point.

Pull and hold tab

Aside from the preconfigured WDS bridge settings, the TEW-740APBO access points will also be

configured with the following default settings:

Verify connectivity between the two access points before mounting.

TEW-740APBO #1

Mode: WDS Mode

IP Address: 192.168.10.50

Netmask (Subnet Mask): 255.255.255.0

IP Gateway (Default Gateway): 192.168.10.1

Primary DNS: 192.168.10.1

TEW-740APBO #2

Mode: WDS Mode

IP Address: 192.168.10.51

Netmask (Subnet Mask): 255.255.255.0

IP Gateway (Default Gateway): 192.168.10.1

Primary DNS: 192.168.10.1

2. Remove the tab on the far left by gently bending it back and forth until the tab is removed.

This will create the opening for a RJ-45 network cable to be routed through.

Tab

3. Using a network cable, connect one end of the cable to the LAN (PoE) port and push the cable

into the cable guide on the far left, then through the opening that was created in the previous

step.

Cable Guide

ENGLISHFRANÇAISDEUTSCH

ESPAÑOLРORTUGUÊS

4. Connect the other end of the network cable to the P+DATA OUT port on the included PoE

injector.

5. Connect the included power adapter to the PoE injector POWER IN on the included PoE

injector.

6. Plug the connected power adapter into a power outlet.

7. Confirm the device is powered on through the LED indicators.

8. Assign a static IP address to your computer's network adapter in the subnet of 192.168.10.x

(e.g. 192.168.10.10) and subnet mask of 255.255.255.0.

9. Using another network cable, connect one end to the 10/100 DATA IN port on the included

PoE injector for either the first or second access point.

10. Connect the other end of the network cable to your computer's Ethernet port.

Note: Repeat Steps 1-7 to power on and connect the second access point.

Included PoE Injector

LAN1 (PoE)

P+DATA OUT

POWER IN 10/100Mbps DATA IN

12. To verify connectivity on your computer, open a command prompt or terminal application

window and type in the following commands.

11. Make sure both access points are powered on approximately 15 ft. (5 m) apart from one

another with front of access points directly facing each other.

15 ft. (5m)

LAN1 (PoE)

P+DATA OUT

POWER IN

P+DATA OUT

10/100Mbps DATA IN

TEW-740APBO #1 TEW-740APBO #2

LAN1 (PoE)

POWER IN

ENGLISHFRANÇAISDEUTSCH

ESPAÑOLРORTUGUÊS

A successful connectivity test will appear similar to the result below for each access point. Ping

replies and 0% packet loss will indicate a successful point to point bridge connection between

the two access points.

Note: If the connectivity test fails, wait for about a minute and try again. Make sure there are no

obstacles between the two access points when running the connectivity test and make sure the

two access points are not too close together.

® ®

Note: In Windows , you can use the Command Prompt application and in Mac , you can

Terminal application to run the commands for connectivity testing.

ping 192.168.10.50

ping 192.168.10.51

3. Ground Wire and Pole Mount Installation

1. Locate the grounding point located in the bottom section of the enclosure. Using a Phillps

screwdriver, remove the grounding point screw (counter clockwise) and attach the included

grounding wire to the grounding point screw. Then reattach the ground screw (clockwise)

along with the grounding wire. After installing the grounding wire, remove another tab on the

enclosure by gently bending back and forth until the tab is removed. This will create the

opening for the ground cable to be routed through.

Note: The ground wire may need to be cut and extended using additional ground wire in order

to reach a proper grounding point.

Tab

Grounding point

Indice

Altri manuali TRENDnet Punto di accesso wireless

TRENDnet

TRENDnet TEW-WLC100 Manuale utente

TRENDnet

TRENDnet TEW-212APBO Manuale utente

TRENDnet

TRENDnet TEW-410APB Manuale utente

TRENDnet

TRENDnet TEW-410APBplus Manuale utente

TRENDnet

TRENDnet TEW-630APB - Wireless Access Point Manuale utente

TRENDnet

TRENDnet TEW-740APBO Manuale utente

TRENDnet

TRENDnet TEW-814DAP Manuale utente

TRENDnet

TRENDnet TEW-230APB Manuale utente

TRENDnet

TRENDnet TEW-630APB - Wireless Access Point Manuale utente

TRENDnet

TRENDnet TEW-410APBplus Manuale utente

TRENDnet

TRENDnet TEW-430APB - Wireless Access Point Manuale utente

TRENDnet

TRENDnet TEW-434APB - 54Mbps Wireless G PoE Access... Manuale utente

TRENDnet

TRENDnet TEW-510APB Manuale utente

TRENDnet

TRENDnet TEW-821DAP Manuale utente

TRENDnet

TRENDnet TEW-841APBO Manuale utente

TRENDnet

TRENDnet TEW-821DAP Manuale utente

TRENDnet

TRENDnet TEW-AP100plus Manuale utente

TRENDnet

TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... Manuale utente

TRENDnet

TRENDnet TEW-638AP Manuale utente

TRENDnet

TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... Manuale utente

TRENDnet

TRENDnet TPL-410AP Manuale utente

TRENDnet

TRENDnet TEW-820AP Manuale utente

TRENDnet

TRENDnet TEW-510APB Manuale utente

TRENDnet

TRENDnet P600 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente