TRIATEK CMS-2000 Manuale utente

CMS-2000

User Guide

Central Monitoring Station

LIT-12013738

February 2023

CMS-2000

LIT-12013738

Risk of Personal Injury or Property Damage.

For use in a controlled environment only. Refer to installation instructions for environmental conditions.

Risk of Electric Shock.

Disconnect the power supply before making electrical connections. Contact with components carrying hazardous voltage can cause

electric shock and may result in severe personal injury or death.

Disconnect all electric power sources from the CMS-2000 Central Monitoring Station before removing the CMS-2000 Central

Monitoring Station cover. Contact with internal components carrying hazardous voltage can cause electric shock and may result in

severe personal injury or death.

IMPORTANT: Do not install or use this CMS-2000 Central Monitoring Station in or near environments where corrosive substances or

vapors could be present. Exposure of the CMS-2000 monitor to corrosive environments may damage the device’s internal components

and will void the warranty.

IMPORTANT: Do not install this CMS-2000 Central Monitoring Station in condensing, wet, or damp environments. Moisture may cause

damage to the CMS-2000 monitor.

IMPORTANT: Only qualied personnel should install or service Johnson Controls® products. These instructions are a guide for such

personnel. Carefully follow all instructions in this document and all instructions for the CMS-2000 Central Monitoring Station.

IMPORTANT: Use copper conductors only. Make all wiring connections in accordance with local, national, and regional regulations. Do

not exceed the CMS-2000 Central Monitoring Station’s electrical ratings.

Risk of Property Damage.

Do not apply power to the station before checking all wiring connections. Short circuited or improperly connected wires may result in

permanent damage to the equipment.

Risk of Property Damage.

Do not run network communication cables in the same conduit, raceway, or panel with any high-voltage (greater than 30 VAC) wiring.

Isolate all network wiring and all network devices from high-voltage wiring and equipment. Failure to isolate network wiring and

network devices from high-voltage wiring and equipment can result in damage to network devices or poor network performance.

Risk of Property Damage.

Label all wires prior to disconnecting the equipment. Failure to label the wires may cause improper equipment operation after

reconnecting the equipment.

IMPORTANT: Make all wiring connections in accordance with the National Electrical Code and local regulations. Use proper Electrostatic

Discharge (ESD) precautions during installation and servicing to avoid damaging the electronic circuits of the CMS-2000 Central

Monitoring Station.

IMPORTANT: Maintain proper polarity and voltage or current ratings. Improper polarity or exceeding the voltage or current ratings will

void the warranty.

IMPORTANT: Do not install the CMS-2000 Central Monitoring Station where the maximum temperature exceeds 125°F (52°C). Installing

the device where maximum temperatures exceed 125°F (52°C) may cause damage to the CMS-2000 Central Monitoring Station and may

void the warranty.

CMS-2000 Central Monitoring Station User Guide

CMS-2000

LIT-12013738

Risque de blessure corporelle ou de dommages matériels.

Pour utilisation dans un environnement contrôlé uniquement. Consulter le guide d’installation pour les conditions environnementales.

Risque de décharge électrique.

Débrancher l’alimentation avant de réaliser tout branchement électrique. Tout contact avec des composants conducteurs de tensions

dangereuses risque d’entraîner une décharge électrique et de provoquer des blessures graves, voire mortelles.

Déconnecter toutes les sources d’alimentation électrique du CMS-2000 Central Monitoring Station avant de ouvrir le capot du CMS-

2000 Central Monitoring Station.Tout contact avec des composants internes conducteurs de tensions dangereuses risque d’entraîner

une décharge électrique et de provoquer des blessures graves, voire mortelles.

Risque de dégâts matériels.

Ne pas mettre le système sous tension avant d’avoir vérié tous les raccords de câblage. Des ls formant un court-circuit ou

connectés de façon incorrecte risquent d’endommager irrémédiablement l’équipement.

Risque de dégâts matériels.

Ne passez pas les câbles de communication réseau dans les mêmes gaines, chemins de câbles ou panneaux que les câbles à

haute tension (supérieure à 30 Vca). Isolez tous les câbles et appareils réseau des câbles et appareils à haute tension. Un défaut

d’isolement des câbles et appareils à haute tension peut provoquer des dommages aux appareils réseau et réduire les performances

du réseau.

Risque de dégâts matériels.

Etiquetez tous les câbles avant de débrancher l’équipement. Le non-respect de cette précaution peut amener un fonctionnement

anormal après redémarrage de l’équipement.

IMPORTANT : N’installez ou n’utilisez pas CMS-2000 Central Monitoring Station dans, ou près, d’environnements où des substances

ou vapeurs corrosives peuvent être présentes. L’exposition du CMS-2000 à des environnements corrosifs peut endommager les

composantes internes de l’appareil et annulera la garantie.

IMPORTANT : N’installez pas CMS-2000 Central Monitoring Station dans un environnement humide, mouillé ou il se produit de la

condensation. L’humidité peut causer des dommages au CMS-2000.

IMPORTANT : Seul le personnel qualié peut installer et entretenir les produits Johnson Controls. Ces instructions constituent un guide

pour ce type de personnel. Suivez attentivement toutes les instructions de ce document et toutes les instructions du CMS-2000 Central

Monitoring Station.

IMPORTANT : Assurez-vous que tous les branchements de câbles sont e󰀨ectués selon le Code national de l’électricité et les

réglementations locales. Utilisez une bonne protection contre les décharges électrostatiques (ESD) pendant l’installation et l’entretien

pour éviter d’endommager les circuits électroniques du CMS-2000 Central Monitoring Station.

IMPORTANT : Conservez la bonne polarité et la bonne tension ou le bon courant. Une mauvaise polarité ou le dépassement de la

tension ou du courant annulera la garantie.

IMPORTANT : N’installez pas le contrôleur d’environnement critique CMS-2000 où la température maximum dépasse 52 °C (125 °F).

Installer l’appareil dans un environnement où la température maximum dépasse 52 °C (125 °F) peut endommager CMS-2000 Central

Monitoring Station et peut annuler la garantie.

IMPORTANT : N’utilisez que des conducteurs en cuivre. Assurez-vous que tous les branchements de câbles sont e󰀨ectués selon les

réglementations locales, nationales et régionales. Ne dépassez pas les spécications électriques du CMS-2000 Central Monitoring

Station.

CMS-2000 Central Monitoring Station User Guide

CMS-2000

LIT-12013738

Table of contents ......................................................................................................................................................................... 4

Introduction.................................................................................................................................................................................. 5

Display overview ......................................................................................................................................................................... 5

Initial setup................................................................................................................................................................................... 7

Completing the initial setup .................................................................................................................................................... 7

Conguration............................................................................................................................................................................... 7

Global settings............................................................................................................................................................................. 7

Choosing a language ............................................................................................................................................................ 7

Choosing a unit of measure .................................................................................................................................................. 7

Display module settings conguration ..................................................................................................................................... 7

Turning on and adjusting the brightness of the 360˚ Safety Halo ......................................................................................... 8

Adjusting the screen brightness ............................................................................................................................................. 9

Turning o󰀨/on the Keyboard Clicks ........................................................................................................................................ 9

User accounts and security........................................................................................................................................................ 9

Admin user capabilities ......................................................................................................................................................... 9

Restricted user capabilities ................................................................................................................................................... 9

User name and password requirements ............................................................................................................................... 9

Creating the admin user account and password ................................................................................................................. 10

Creating a restricted user and PIN password ...................................................................................................................... 10

Deleting users ..................................................................................................................................................................... 10

Changing a user name ........................................................................................................................................................ 10

Changing the access level of a restricted user to an admin user ........................................................................................ 10

Changing the access level of an admin user to a restricted user ........................................................................................ 11

Updating the PIN of a restricted user .................................................................................................................................. 11

Monitor setup............................................................................................................................................................................. 11

Adding a monitored device................................................................................................................................................... 11

Monitoring multiple parameters from the same device ........................................................................................................ 11

To add multiple parameters from the same device, you need to add the same device multiple times. ............................... 11

Delete a monitored device.................................................................................................................................................... 11

Edit the address of a monitored device................................................................................................................................ 12

Alarms ........................................................................................................................................................................................ 12

Enabling the alarm status .................................................................................................................................................... 12

Setting the audible alarm delay............................................................................................................................................ 12

Changing the alarm mode.................................................................................................................................................... 12

Silencing the alarm............................................................................................................................................................... 12

Diagnostics ................................................................................................................................................................................ 12

Viewing the About this CMS information ............................................................................................................................. 12

Rebooting the monitor ......................................................................................................................................................... 13

Restricted level user guide....................................................................................................................................................... 13

Navigating the home screen................................................................................................................................................. 13

Viewing Room Details ......................................................................................................................................................... 13

Changing the parameter displayed on the home screen...................................................................................................... 13

Changing the alarm mode.................................................................................................................................................... 14

Silencing the alarm............................................................................................................................................................... 14

Repair information..................................................................................................................................................................... 15

North American Emissions Compliance ................................................................................................................................. 15

Table of contents

CMS-2000 Central Monitoring Station User Guide

CMS-2000

LIT-12013738

Introduction

Display overview

Figure 1: CMS-2000 home screen monitoring multiple FMS controllers

1 2 3

Callout Description

1P = Positive isolation mode

2N = Negative isolation mode

3Analog input name

4Normal status icon

5Quick access audible alarm mode

6Sensor reading

7Settings menu

8End user demonstration video

Table 1: FMS-2000M Critical Environment Monitor display and icons

The CMS-2000 Central Monitoring Station provides instant status verication for up to eight rooms, eight fume hoods, or a combination

of rooms and hoods. You can use the CMS-2000 as a nurse station annunciator, or to monitor multiple spaces in large laboratories.

The CMS-2000 creates a centralized location to easily access critical information like room pressure, isolation mode, exhaust air ow,

face velocity, and alarm status of multiple spaces and fume hoods. If a monitored parameter goes outside its prescribed range, it

activates an audible and visual alarm that alerts staff to the alarm condition. Users can access vital information on a single screen to

quickly make informed decisions. This ensures that critical spaces are safe for occupancy.

The CMS-2000 features the patented 360˚ Safety Halo™ edge lighting, which you can use to monitor status down long corridors with a

simple glance. The green, yellow, and red visual alarms also help to reduce audible alarm fatigue beacuse you can silence the audible

alarm with the tap of a nger.

The CMS-2000 communicates on its own subnet with the FMS-2000C and HMS-1655 family of controllers.

Note: The CMS-2000 does not monitor the FMS-2000M Critical Environment Monitor.

CMS-2000 Central Monitoring Station User Guide

CMS-2000

LIT-12013738

Callout Description

1Occupied

2Unoccupied

3Quick access audible alarm mode

4Parameter status icon

5Warning status icon

6Alarm status icon

7Standby

Note: If you are monitoring an FMS controller, this icon displays as Neutral.

8Settings menu

1 2 3

Figure 2: CMS-2000 monitoring multiple HMS1655 controllers

Figure 3: CMS-2000 home screen monitoring one controller

Table 2: CMS-2000 monitoring HMS1655 controllers

CMS-2000 Central Monitoring Station User Guide

CMS-2000

LIT-12013738

Initial setup

Completing the initial setup

When the CMS-2000 Central Monitoring Station starts for the rst time, you need to congure the device language and units of

measurement.

The rst screen that appears in the initial setup is the Language screen.

1. On the Language screen, scroll to the language you want to use and tap the Checkmark icon.

2. On the Terms and Conditions screen, tap the Accept button

3. On the Global screen, expand Units and tap to select Imperial or Metric.

4. Tap the Checkmark icon to save the settings.

5. Tap Proceed to complete the initial setup.

Note: At any time, you can make changes to your initial settings in the Settings menu.

Conguration

Global settings

After you complete the initial setup, the settings menu appears. You can congure the following settings:

• Global settings

• User Accounts

• Monitor Setup

• Alarms

• Diagnostics

• Documentation

In Global settings, you can change settings that impact the entire CMS-2000 Central Monitoring Station.

Choosing a language

1. On the home screen, tap the Settings icon.

2. To view global settings, tap Global.

3. To view all language options, tap the Language arrow.

4. To choose a language, scroll to your preferred language.

5. To save your language selection, tap the Checkmark icon.

Choosing a unit of measure

1. On the home screen, tap the Settings icon.

2. To view global settings, tap Global.

3. On the Global screen, expand Units to select Imperial or Metric.

4. Collapse Units to save the settings.

Table 2: Monitor DIP switch congurations for the operating mode

Figure 4: DIP switch run and demo modes

Display module settings conguration

Run mode

12 3 4 12 3 4

Demo mode

O O O O O OO

CMS-2000 DIP switch position Run mode Demo mode

1Off Off

2Off Off

3Off Off

4 On Off

CMS-2000 Central Monitoring Station User Guide

Note: Demo mode is a test display for demonstration purposes. You do not need to connect the CMS-2000 to the FMS-2000C or the

HMS-1655 to use demo mode.

CMS-2000

LIT-12013738

Figure 4: Normal mode Figure 5: Alarm mode

Figure 6: Warning mode

Turning on and adjusting the brightness of the 360˚ Safety Halo

The 360˚ Safety Halo illuminated edge allows sta󰀨 to easily monitor spaces down long corridors. A green light indicates normal status,

red indicates alarm status, and yellow indicates warning status.

1. On the home screen, tap the Settings icon to enter the Settings menu.

2. To view global settings, tap Global.

3. To adjust settings for the 360˚ Safety Halo, tap the Safety Halo arrow.

4. To turn the 360° Safety Halo on, switch on Enabled.

5. To adjust the brightness, move the slider to increase or decrease the brightness.

6. To conrm the new settings, tap the Checkmark icon.

Figure 7: Neutral isolation mode

CMS-2000 Central Monitoring Station User Guide

CMS-2000

LIT-12013738

Adjusting the screen brightness

1. On the home screen, tap the Settings icon.

2. To view global settings, tap Global.

3. Expand Screen Brightness and move the slider to increase or decrease the brightness of the screen.

4. To conrm the settings, tap the Checkmark icon.

Turning o󰀨/on the Keyboard Clicks

1. On the home screen, tap the Settings icon.

2. To view global settings, tap Global.

3. To turn the keyboard clicks on or o󰀨, tap the Keyboard Clicks switch.

User accounts and security

Admin user capabilities

Admin users have access to the settings menu and the ability to make changes to the settings.

When you create an admin user, the following conventions apply:

• After you create an admin user account, you cannot delete it unless you rst create another admin user.

• Only an authenticated admin user can create users.

• Admin users can delete admin users, restricted users, or multiple users simultaneously.

• Admin users can change a single restricted user or multiple restricted users to admin level simultaneously.

• Admin users can select all users.

• Admin users can delete multiple selected users.

Restricted user capabilities

A restricted user must authenticate to view the room detail screen and change the alarm status.

An individual user or group must identify themselves with a user name before they enter a personal identication number (PIN).

User name and password requirements

To create a user name, follow these minimum requirements:

• English only

• Alphanumeric

• One letter minimum

• 3 to 20 characters in length

• The @ symbol is the only special character that can be used for user names.

• You cannot duplicate user names.

To set up an admin password, follow these minimum requirements:

• English only

• Alphanumeric

• 6 to 12 characters in length

• One letter minimum

• One digit minimum

• The @ symbol is the only special character that can be used for passwords.

To set up a PIN password for a restricted user, use the following criteria:

• 0 to 9 numeric

• 4 to 8 digits in length

When you set up users and passwords, you restrict the use of the CMS-2000 Central Monitoring Station to specic groups of people.

This is not mandatory, but if you do not create users and passwords, anyone can access all functions of the CMS-2000. There are two

access levels:

• Admin level users

• Restricted users.

CMS-2000 Central Monitoring Station User Guide

CMS-2000

LIT-12013738

Creating the admin user account and password

The rst user must be an admin. You cannot set up a restricted user until you set up an admin. Admin level users have access to the

entire device.

1. On the home screen, tap the Settings icon to enter the Settings menu.

2. To view all user accounts information, tap User Accounts.

3. On the User Accounts screen, tap the Create User arrow.

4. To change the admin user name, tap the User Name arrow and enter the new user name. For more information, see User name

and password requirements.

5. To select the access level for the new admin user account, expand Access Level and tap Administrator.

6. To conrm your settings, tap the Checkmark icon.

7. On the Create Password screen, enter your new password twice. For more information, see User name and password

requirements.

8. To complete the admin user account and password setup, tap the Checkmark icon.

Creating a restricted user and PIN password

A restricted user can access the device detail screen and adjust the alarm mode.

1. On the home screen, tap the Settings icon to enter the Settings menu.

2. To view all user accounts information, tap User Accounts.

3. On the User Accounts screen, tap the Create User arrow.

4. To change the restricted user name, tap the User Name arrow and enter the new user name. For more information, see User name

and password requirements.

5. To select the access level for the new restricted user account, expand Access Level and tap Restricted User.

6. To conrm your settings, tap the Checkmark icon.

7. On the Create PIN screen enter your new PIN twice. For more information, see User name and password requirements.

9. To complete setting up the restricted user account and PIN, tap the Checkmark icon.

Deleting users

1. On the home screen, tap the Settings icon to enter the Settings menu.

2. To view all user accounts information, tap User Accounts.

3. On the user accounts screen, tap the Manage Users arrow.

4. Tap the three dots next to MANAGE USERS.

5. Tap the users you want to delete and tap Delete.

6. Optional: If you want to delete all users, tap Select All and Delete.

7. In the DELETE DEVICE screen, tap the Delete button.

Note: When you choose the optional step to delete all users, you delete all admin and restricted users except for the admin user

account that you used to log on.

Changing a user name

1. On the home screen, tap the Settings icon to enter the Settings menu.

2. To view all user accounts information, tap User Accounts.

3. To change a user name, tap Edit next to a user name.

4. On the Edit User screen, tap the User Name arrow and enter a di󰀨erent user name.

5. To conrm the new user name, tap the Checkmark icon.

Changing the access level of a restricted user to an admin user

1. On the home screen, tap the Settings icon to enter the Settings menu.

2. To view all user accounts information, tap User Accounts.

3. To change the access level of a restricted user, tap Edit.

4. On the Edit User screen, tap Restricted User and select Administrator.

5. Tap Create Password and enter a new password twice.

6. To conrm the change, tap the Checkmark icon.

CMS-2000 Central Monitoring Station User Guide

Indice

Altri manuali TRIATEK Strumento di misura

TRIATEK

TRIATEK DDN-SW1 Manuale utente

TRIATEK

TRIATEK VMS-1655M Manuale utente

TRIATEK

TRIATEK FMS-2000M Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente