Ubiquiti EdgeRouter 12 Manuale utente
10-Port Gigabit Router with PoE
Passthrough and 2 SFP Ports
Model: ER-12
Introduction
Thank you for purchasing the Ubiquiti Networks®
EdgeRouter™. This Quick Start Guide is designed to guide you
through installation and also includes warranty terms.
Package Contents
EdgeRouter ER-12
Wall Mount
Screws (Qty. 2)
Wall Mount
Anchors (Qty. 2)
Ground
Screw
Power Adapter
(24V, 1A)
Cable Clip
Installation Requirements
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit:
www.ubnt.com/toughcable
WARNING: To reduce the risk of fire or electric shock,
do not expose the EdgeRouter to rain or moisture.
Note: Although the cabling can be located outdoors,
the EdgeRouter itself should be housed inside a
protective enclosure.
Hardware Overview
Front Panel Ports
Console RJ45 (Ports 0-9) SFP Ports
USB
Interface Description
Console
RJ45 serial console port for Command
Line Interface (CLI) management. Use an
RJ45-to-DB9, serial console cable, also
known as a rollover cable, to connect the
Console port to your computer. (If your
computer does not have a DB9 port,
then you will also need a DB9 adapter.)
Then configure the following settings as
needed:
• Baud rate 115200
• Data bits 8
• Parity NONE
• Stop bits 1
• Flow control NONE
USB Reserved for future use.
RJ45
(Ports 0 - 9)
All RJ45 ports can be used for routing
and support 10/100/1000 Mbps Ethernet
connections. Ports 0 - 7 can be configured
for switching functions using the EdgeOS
Configuration Interface. Port 0 supports
24V Passive PoE In and port 9 supports
optional Passive PoE Out (disabled by
default).
SFP Ports
(Ports 10 - 11)
SFP routing ports are hot-swappable and
support Gigabit fiber SFP modules.
Front Panel Button
Reset
Button Description
Reset
There are two methods to reset the
EdgeRouter to factory defaults:
• Runtime reset (recommended) The
EdgeRouter should be running after
bootup is complete. Press and hold the
Reset button for about 10seconds until
the LED for port eth9 starts flashing and
then becomes solidly lit. After a few
seconds, the LED will turn off, and the
EdgeRouter will automatically reboot.
• Power-on reset Disconnect the Power
Cord from the Power Adapter. Press and
hold the Reset button while connecting
the power (refer to “Connecting Power”
for details). The port LEDs will light up
in sequential order. Keep holding the
Reset button until the System LED starts
flashing blue and white, and then release
the button.
Front Panel LEDs
System
System LED
Note: The System LED functionality has been updated
with firmware v1.10.7. We recommend that you update
the EdgeRouter to the latest firmware.
State Status
Flashing White Bootup in progress.
White
Ready for use, not connected to Ubiquiti®
Network Management System (UNMS™).
See “UNMS Management”.
Blue Ready for use, connected to UNMS.
Steady Blue
with Occasional
Flashing
Ready for use, unable to connect to
UNMS, check connection to UNMSserver.
Quickly Flashing
Blue Used to locate a device in UNMS.
Alternating
Blue/White Firmware upgrade in progress.
Speed/Link/Act PoE Link/Act
RJ45 LEDs
LED State Status
PoE
Off No PoE
Green 24V 2-Pair Passive PoE Output
Speed/
Link/
Activity
Off No Link
Amber Link Established at 10/100 Mbps
Amber
Flashing Link Activity at 10/100 Mbps
Green Link Established at 1000 Mbps (1 Gbps)
Green
Flashing Link Activity at 1000 Mbps (1Gbps)
SFP LED
LED State Status
Link/Act
Off No Link
Green Link Established at 1 Gbps
Green
Flashing Link Activity at 1Gbps
Back Panel
Grounding Point
Ventilation Holes Power
Note: There are additional ventilation holes on the sides
of the EdgeRouter.
Hardware Installation
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
Wall Mounting
To mount the EdgeRouter on a wall, you will need a drill, a
6mm drill bit, and a Phillips screwdriver.
1. Use a 6 mm drill bit to drill two holes 190 mm apart.
2. Insert the Wall Mount Anchors into the holes. Use a Phillips
screwdriver to secure a Wall Mount Screw to each anchor.
Leave a clearance of approximately 3 mm between each
screw head and its anchor.
190 mm
3 mm
Note: You can also mount the EdgeRouter in a
vertical orientation.
3. Position the EdgeRouter with the Ethernet ports facing
down. Place the wall-mount slots of the EdgeRouter over
the screw heads on the wall. Then slide the EdgeRouter
down to lock it into place.
Grounding the EdgeRouter (Recommended)
The EdgeRouter is grounded through the Power Adapter;
however, you can add optional ESD grounding for enhanced
ESD protection.
1. Attach the Ground Screw to secure a ground wire (not
included) to the Grounding Point.
2. Optional: To secure the Power Adapter cord, insert it
into the Cable Clip and secure the Cable Clip using the
GroundScrew.
3. Secure the other end of the ground wire to a grounding block.
Connecting Power
1. Connect the Power Adapter to the Power port.
2. Connect the other end of the Power Adapter to a power
outlet.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Ubiquiti Router di rete
Ubiquiti
Ubiquiti UCK-G2 Manuale utente
Ubiquiti
Ubiquiti EdgePoint R8 Manuale dell'operatore
Ubiquiti
Ubiquiti EdgePoint EP-R8 Manuale utente
Ubiquiti
Ubiquiti EdgeRouter ER-12P Manuale utente
Ubiquiti
Ubiquiti EdgeRouter 4 Manuale utente
Ubiquiti
Ubiquiti UF-LOCO Manuale utente
Ubiquiti
Ubiquiti EdgeRouter Lte 3 Manuale utente
Ubiquiti
Ubiquiti EdgeRouter 6P Manuale utente
Ubiquiti
Ubiquiti 3GStation Professional Manuale utente
Ubiquiti
Ubiquiti EdgeRouter X ER-X Manuale utente
Ubiquiti
Ubiquiti ERLite-3 Manuale utente
Ubiquiti
Ubiquiti ER-12 Manuale utente
Ubiquiti
Ubiquiti ER-4 Istruzioni operative e di manutenzione
Ubiquiti
Ubiquiti Edge Pro ERPro-8 Manuale utente
Ubiquiti
Ubiquiti EdgeRouter ERPro-8 Manuale utente
Ubiquiti
Ubiquiti AiAF-5 Manuale utente
Ubiquiti
Ubiquiti EdgeRouter PoE ERPoe-5 Manuale utente
Ubiquiti
Ubiquiti EdgeRouter ER-8 Manuale utente
Ubiquiti
Ubiquiti PowerBridge M3 Manuale utente
Ubiquiti
Ubiquiti EdgeRouter PoE ERPoe-5 Manuale utente
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza