Ubiquiti NBE-M5-16 Manuale utente

High-Performance 16 dBi

airMAX®CPE

Model: NBE-M5-16

Introduction

Thank you for purchasing the Ubiquiti Networks™NanoBeam™.

This Quick Start Guide is designed to guide you through

the installation, and show you how to access the airOS®

Configuration Interface. This Quick Start Guide also includes

the warranty terms and is for use with the NanoBeamM5,

modelNBE-M5-16.

Package Contents

NanoBeamM5 Ball Joint

Mount

Lock Ring

High-Performance16 dBi

airMAX®CPE

Model:NBE-M5-16

Metal Strap PoE Adapter

(24V, 0.5A)

Power Cord Quick Start Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

The NanoBeam can be mounted on a pole or to a wall. A Metal

Strap (included) is used for pole-mounting. For wall-mounting,

a suitable fastener such as a screw or bolt (not included) is

required.

• 7 mm (¼ in) socket wrench or screwdriver (for

pole-mounting)

• Wall fastener (for wall-mounting)

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks with

industrial-grade shielded Ethernet cable, TOUGHCable from

Ubiquiti Networks.

For more details, visit www.ubnt.com/toughcable

Hardware Overview

LEDs

Reset Button Ethernet Port

(10/100 Mbps)

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoBeam

is already poweredon. Alternatively, the NanoBeam may be

reset remotely via a Reset button located on the bottom of the

PoE Adapter.

Ethernet Port The Ethernet port is used to connect the power

and should be connected to the LAN and DHCP server. Power

can be provided by any of the following:

• PoE Adapter (included)

• Ubiquiti Networks TOUGHSwitch™ PoE

• Ubiquiti Networks EdgeRouter™ PoE

LEDs

Power The Power LED will light blue when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light blue when the wireless signal

strength is above -94 dBm.

LED will light blue when the wireless signal

strength is above -80 dBm.

LED will light blue when the wireless signal

strength is above -73 dBm.

LED will light blue when the wireless signal

strength is above -65 dBm.

Hardware Installation

The NanoBeam can be mounted on a pole or to a wall. Perform

the steps for the appropriate installation:

Pole-Mount

1. Insert the Ball Joint Mount into the Lock Ring with the

threads of the Lock Ring facing the ball joint.

2. Open the Metal Strap and feed it through the base of the

Ball Joint Mount.

*640-00106-02*

640-00106-02

3. Wrap the Metal Strap around the pole. Use a 7 mm (¼ in)

socket drive or screwdriver to turn the screw clockwise and

securely fasten the strap to the pole.

4. Attach the NanoBeam to the Ball Joint Mount and turn the

Lock Ring to secure it. Keep the Lock Ring loose enough to

allow the NanoBeam to pivot for aiming.

Wall-Mount

The NanoBeam must be mounted directly to a wood stud

or other structurally stable surface to avoid damage to the

mounting hole when you adjust the aim.

1. Mark the desired location of the mounting point.

2. If needed, drill a pilot hole for the fastener.

3. Insert the Ball Joint Mount into the Lock Ring with the

threads of the Lock Ring facing the ball joint.

4. Attach the Ball Joint Mount to the wall by inserting a

fastener through the center of the ball joint, and into the

hole in the wall. Securely tighten the fastener.

5. Attach the NanoBeam to the Ball Joint Mount and turn the

Lock Ring to secure it. Keep the Lock Ring loose enough to

allow the NanoBeam to pivot for aiming.

Aiming

1. Ensure the opening of the Ethernet cable is pointed

towards the ground.

2. Aim the front of the NanoBeam towards the other end of

the wireless link.

3. Hand-tighten the Lock Ring to lock the aim.

Note: Do not use a tool to tighten the Lock Ring.

Tighten the Lock Ring by hand only.

Connecting to the PoE Adapter

1. Remove the port cover by pressing down the center of the

cover and sliding the cover out.

2. Connect an Ethernet cable to the Ethernet port.

3. Replace the port cover.

Altri manuali per NBE-M5-16

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ubiquiti Punto di accesso wireless

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Manuale utente

Ubiquiti

Ubiquiti UniFi UAP-nanoHD Manuale utente

Ubiquiti

Ubiquiti airFiber AF-11 Manuale utente

Ubiquiti

Ubiquiti UniFi Dream Machine Manuale utente

Ubiquiti

Ubiquiti M5 GPS Rocket M Series Manuale utente

Ubiquiti

Ubiquiti UniFI UAP-AC Manuale utente

Ubiquiti

Ubiquiti UniFi Manuale utente

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Manuale utente

Ubiquiti

Ubiquiti UniFi AC SHD Manuale utente

Ubiquiti

Ubiquiti UAP-Outdoor Manuale utente

Ubiquiti

Ubiquiti GigaBeam GBE Manuale utente

Ubiquiti

Ubiquiti RocketM Series Manuale utente

Ubiquiti

Ubiquiti RocketM Manuale utente

Ubiquiti

Ubiquiti BulletM2-HP Manuale utente

Ubiquiti

Ubiquiti Rocket M Series Manuale utente

Ubiquiti

Ubiquiti UniFi AC AP Mesh Pro Manuale utente

Ubiquiti

Ubiquiti Rocket R5ACL Manuale utente

Ubiquiti

Ubiquiti PowerBeam PBE2ACN Manuale utente

Ubiquiti

Ubiquiti LTU-Lite Manuale utente

Ubiquiti

Ubiquiti Rocket2AC Prism Manuale utente

Ubiquiti

Ubiquiti airFiber AF 60 Manuale utente

Ubiquiti

Ubiquiti UAP-IW-HD Manuale utente

Ubiquiti

Ubiquiti R5AC-PTP Manuale utente

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente

EnGenius

EnGenius EAP350 Manuale utente