VibrAlign Fixturlaser Laser Kit Istruzioni per il montaggio
Fixturlaser Laser Kit
QUICK TIPS
©2015 VibrAlign, Inc.
Fixturlaser Laser Kit
1
Fixturlaser Laser Kit
1. Rough Alignment
• Vertical: Place scale or straightedge on highest
hub and raise or lower the movable shaft to
within 20 mils (0.020”) of the stationary hub.
• Horizontal: Place scale or straightedge on hub
nearest to you and adjust the movable shaft to
within 20 mils (0.020”) of the stationary hub.
2. Correct Obvious Soft Foot
Loosen all the bolts and nd any obviously loose
shim packs. Add shims as needed to make a snug
t.
3. Follow Tightening Sequence
Follow the same sequence throughout the align-
ment process, and tighten in 3 passes: snug rst,
50% on second pass, completely tight on the
third pass. (View sequence on next page)
PRE-ALIGNMENT
2
Fixturlaser Laser Kit
Bolt Tightening Sequence
4. Make a Final Soft Foot Correction
Loosen one bolt at a time and check for soft
foot with a 2 mil (0.002”) shim or feeler gauge.
Correct any foot with 2 mils or more of soft foot,
then tighten the bolt before proceeding to the
next foot.
PRE-ALIGNMENT
3
Fixturlaser Laser Kit
Set Up
1. Mount the ‘S’ sensor on the stationary shaft or
coupling hub and hand tighten the nut. Turn the
sensor on by pressing the power button.
2. Mount the ‘M’ sensor on the movable shaft or
coupling hub and hand tighten the nut. Use the
tightening tool and tighten further. Turn the sen-
sor on by pressing the power button.
Start the Laser Kit App
1. Ensure Bluetooth is enabled on your device.
2. Click on the Fixturlaser Laser Kit App on your
phone or tablet.
3. The app will search for the sensors and con-
nect via Bluetooth. This will take between 5 to 15
seconds.
4. The laser will turn on.
SET UP
Tighten the nut Press the power button
4
Fixturlaser Laser Kit
SET UP
Aim the Lasers
1. Loosen the adjustment knob of the sensor and
slide the sensors up and down until the line laser
beams hit the middle of the opposite sensor.
2. Fine tune the line laser beam with adjustment
wheel on the opposite side of the sensor.
3. Be precise so that the beam hits the window as
accurately as possible.
4. Note that the sensors will be at different eleva-
tions.
Incorrect Correct
adjustment knob
adjustment wheel
5
Fixturlaser Laser Kit
MEASURE
Enter Dimensions
1. Press the yellow tape measure icon to open the
keypad.
2. Measure the indicated dimension to the nearest
1/8”using the keypad.
3. Continue and enter all dimensions.
Tape measure icon
6
Fixturlaser Laser Kit
Measure Misalignment
1. Press the measurement mode icon. Rotate
the sensors to the 9:00 position and press the
measurement icon.
2. Rotate the sensors to the 12:00 position. Press
the measurement icon again to take the second
measurement. (View the 12:00 position on next
page)
MEASURE
9:00 position and measurement icon
1 . 9:00
2 . 12:00
3. 3:00
Position the
sensors
within ± 3°
7
Fixturlaser Laser Kit
3. Rotate the sensors to 3:00, measure. The
results will be displayed on screen.
12:00 position
MEASURE
8
Fixturlaser Laser Kit
Evaluating the Results
1. Vertical results are displayed at the top of the
screen, horizontal results at the bottom.
2. Green coupling icons indicate values that are
in tolerance.
3. Orange values are within 2x tolerance.
4. Red values are more the 2x the tolerance level.
MEASURE
9
Fixturlaser Laser Kit
CORRECTION
Using the Verti-Zontal™Process
First Correct the Vertical Misalignment
1. Press the shim icon in the bottom right
corner of the screen.
2. Loosen all the bolts on the movable machine.
3. Follow screen instructions for removing or
inserting shims.
Do not re-tighten the bolts.
Next Correct the Horizontal Misalignment
1. First press the ‘live reading’ icon in
the bottom right corner of the screen.
2. To ensure the live readings are for the horizon-
tal direction make sure the sensors are at either
3:00 or 9:00.
3. Make the largest adjustment rst. The arrows
indicate the direction of adjustment. (View screen
on the next page)
Remove
Shims
Add
Shims
Questo manuale è adatto per i seguenti modelli
4
Indice
