Vivotek AE-153 Manuale utente
VIVOTEK
Installation Guide
AM-117
AM-114
AE-153
473 mm
184
107.86
114.38
68
34.45
Installation
A pendant head (AM-114) is required.
You can either use standard pendant pipes, AM-116 (20cm) and AM-117 (40cm).
AE-153 Installation Guide
(Weather-proof Housing and Bracket for
SC8131)
QIG part no.: 625044900G
VIVOTEK
2 - Installation Guide
2
1
1. Determine a hard surface ceiling location, and use the included alignment sticker for
marking three mounting holes as where the holes will be drilled to secure the pendant
head.
2. Hammer in the plastic anchors.
Installing the Pendant Head and Pendant Pipe
n 50.8
17
200
1 1/2" PS11
n 50.8
17
400
1 1/2" PS11
AM-116, AM-117 Mechanical Drawings
VIVOTEK
Installation Guide
3
4
5
7
6
3. Secure the pandant head using the included screws.
4. Install the pendant pipe of a preferred length.
5. Tighten the socket hex screw using the hex wrench.
6. Install the AE-153 top bracket.
7. Secure the installation by tightening the socket hex screw.
AM-114
AM-117
AE-153
8. Prepare the AE-153 bracket components. The components are shown below:
SC8131
Slide bracket
Housing
Cable gland
Side cover
Thermal pads
This side with a
model name tag.
The default camera
front side.
VIVOTEK
4 - Installation Guide
9. Route a CAT5e Ethernet cable through the pendant pipe, and install the cable gland
components to the Ethernet cable.
4.3 ~ 6.4mm
Sliding edge towards
the clamp head.
10. Remove the side cover from the side with a name tag, and remove slide bracket from
the chassis.
Slide bracket
Model name tag.
11. Remove two retention screws from the back of camera.
VIVOTEK
Installation Guide
12. Attach 4 thermal pads to the 4 corners on the back of the SC8131 camera.
13. Place the slide bracket on top of the camera. The opening should provide access to the
indented area on the back of the camera. Make sure another long piece of thermal pad
is properly installed on the slide bracket.
Indented area
Thermal pad
14. Secure the slide bracket to camera using 2 M3 screws.
VIVOTEK
6 - Installation Guide
15. You can install the waterproof cable gland to chassis. Leave some of the Ethernet
cable at the outside of the chassis for making the connection. Do not completely tighten
the cable gland yet.
17. Connect the Ethernet connector to the camera's RJ45 socket. When done, slide the
camera into the chassis by aligning with the grooves within the chassis.
16. Before you install the camera into
chassis, remove the protective sheet from
the camera.
VIVOTEK
Installation Guide
18. Secure the slide bracket by driving an M3 screw.
19. Tighten up the cable gland, adjust the cable length, and install the side cover.
20. Secure the chassis to bracket by driving 4 M3 screws.
x4
VIVOTEK
8 - Installation Guide
22. Remove the protective sheet from the bottom of the chassis.
21. Loosen the hex socket crew and adjust the orientation, the shooting angle, or the tilt
angle if necessary.
Indice
Altri manuali Vivotek Accessori per fotocamere
Vivotek
Vivotek Bullet Series Manuale utente
Vivotek
Vivotek AE-238 Manuale utente
Vivotek
Vivotek AE-237 Manuale utente
Vivotek
Vivotek CaMate Series Manuale utente
Vivotek
Vivotek Stainless Steel Housing Series Manuale utente
Vivotek
Vivotek Fixed Dome Series Manuale utente
Vivotek
Vivotek AE-252 Manuale utente
Vivotek
Vivotek Fixed Dome AM-116 Manuale utente
Vivotek
Vivotek AM-108 Manuale utente
Vivotek
Vivotek IP8152 Manuale utente
