Vivotek AM-516 Manuale utente
IP Surveillance
User’s Manual
AM-516
Adaptor Ring
Complies with FD8162 fixed dome camera
Rev. 1.0
2
Overview
I
AM-516 Adaptor Ring
You may also refer to VIVOTEK's website for the list of supported models.
Adaptor ring for FD8162 xed dome camera. The
supported installation types are:
1. to a 90º wall-mount bracket (AM-211).
2. to a 4" or 4
11/16
" US standard, metal junction box.
Installation with a Wall-mount Bracket (AM-211)
II
Above are the locations of different groups of mounting holes for matching different
cameras: Use the A group holes for FD8162.
Hole Type Applicable Cameras Screw No. of
screw
A
FD8161 / FD7132 / FD7131
M4X15 2
FD8162 4
BFD8133V / FD8134V M4X8XD6 3
CFD8133 / FD8134 M3X6 2
DPZ7111 / PZ7112 / PZ7121 / PZ7122 / PZ7131 / PZ7132 / PZ7151 /
PZ7152 / PZ81x1W / PZ81x1 M3X6 2
For cabling and conguration details with each network camera, please refer to their
documentation.
Mounting Hole Denitions
Refer to the table below for the description of the included screws:
Screw Description Quantity Applies to
M4X15 Phillips pan head 4 A holes
M3X6 Phillips pan head 2 D holes for PZ
and PT series
M4X8XD6 Phillips pan
head
3 B holes
M4X25XD9 Phillips pan
head
4Securing the
bracket to wall
Plastic anchors 4Securing the
bracket to wall
NOTE:
1. It is presumed that the corresponding AM-211 wall-mount bracket is installed with a
hole drilled on the wall for routing power lines, DI/DO, and Ethernet cables.
2. Route cables before you secure the wall-mount bracket to a wall.
3. For details on the cable connections with each camera, please refer to their Quick
Installation Guide.
NOT USED!
4
Below is a sample procedure using AM-211 wall mount bracket and an FD8162:
1. Determine a hard surface wall location, and use the four mounting holes on the bracket
to mark the positions where holes will be drilled to secure the bracket.
Wall Mount Installation
M4X15
A* holes
Camera Lens Orientation
2. Drill holes on the wall for securing the bracket and for routing cables.
3. Route cables through the wall and bracket.
4. Secure the wall mount bracket to the wall using the included screws and plastic
anchors.
5. Rotate the adaptor ring to match the camera lens orientation your prefer, e.g., to the
front or to the left. Secure the adaptor ring to bracket using the M4X15 screws to the A2
and A4 holes on the bracket.
5
English
6. Secure the camera to the adaptor ring using the included screws.
7. Connect power lines and cables to the camera.
8. Proceed with initial setup such as enabling network access, focus tuning, or zooming.
When done, secure the outer dome cover.
NOTE:
Use the correct type of screws when installing cameras to
the mounting cap. Refer to page 2 for the screw type.
6
D REF.
THREE 1/2 [16] KNOCKOUTS
IN BOTTOM
101.60
[4]
85.72
[3 3/8]
85.72 [3 3/8]
101.60 [4] #8-32 TAP
2 HOLES
6.75 [17/64] DIA. HOLE MIN. OF FOUR
LOCATED AS SHOWN
THREE 1/2 [16] KNOCKOUTS ON
OPPOSITE SIDES
OPTIONAL
MOUNTING
HOLES
D KNOCKOUTS, TWO
REQD. IN BOTTOM
Below are the basic dimensions of standard, US style, 4 in. or 4 11/16 in. junction boxes.
The AM-516 adaptor ring complies with such junction box.
Ceiling Mount to a Junction Box
III
#8-32 TAP
4 HOLES
THREE 1/2 [16] KNOCKOUTS
IN BOTTOM
119.06
[4 11/16]
95.26
[3 3/4]
MIN.
CLEAR.
69.85
[2 3/4]
119.06 [4 11/16]
6.75 [17/64] DIA. HOLE
MIN. OF FOUR
LOCATED AS SHOWN
TWO 1/2 [16] OR 3/4 [21] KNOCKOUTS
IN BOTTOM
THREE 1/2 [16] KNOCKOUTS ON
EACH SIDE, 12 REQD. TOTAL
OPTIONAL
MOUNTING
HOLES
107.95
[4 1/4]
Align the adaptor ring with holes on the junction box
following the markings on the ring.
Use the included 8# 1/2 screws for mounting to a
junction box.
7
English
To install camera with the adaptor ring:
1. Use the included machine screws to fasten the adaptor ring to a 4 in. or 4 11/16 in.
junction box.
2. Route cables through the opening.
3. Secure the camera to the adaptor ring onto the 3 elevated mounting holes.
4. Connect the cabling, use the Ethernet connection to open a web console. Adjust the
camera's shooting angle, focus, and zoom. When done, install the dome cover.
8# 1/2
Machine screws
M4*12mm
Panhead screws,
black
Nickel
alloy
Camera Lens Orientation
Orient the adaptor ring to match the tap holes on the junction
box, so that the camera's shooting angle can be more easily
directed to the area of your interest, although the camera
comes with mechanisms to adjust lens orientation.
Note that the junction box should be able to carry a weight of
at least 3 kilograms.
8
This page is intentionally left blank.
Indice
Altri manuali Vivotek Accessori per fotocamere
Vivotek
Vivotek AE-237 Manuale utente
Vivotek
Vivotek AM-520 Manuale utente
Vivotek
Vivotek Bullet Series Manuale utente
Vivotek
Vivotek IP8152 Manuale utente
Vivotek
Vivotek AE-238 Manuale utente
Vivotek
Vivotek Stainless Steel Housing Series Manuale utente
Vivotek
Vivotek CaMate Series Manuale utente
Vivotek
Vivotek Fixed Dome Series Manuale utente
Vivotek
Vivotek AM-108 Manuale utente
Vivotek
Vivotek Fixed Dome AM-116 Manuale utente
