Volt VHS-6719-25-BBZ Manuale utente
VOLT®Low Voltage Landscape Lighting
VOLT® 18” High Output Brass Rotatable LED Hardscape Light
VHS-6719-25-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2021, VOLT®Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -
VOLT® 18” High Output Brass Rotatable LED Hardscape Light
VHS-6719-25-BBZ
Important Safety Instructions: Read Before Installation
INSTALLATION INSTRUCTIONS
!
www.voltlighting.com
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. DO NOT INSTALL in walls where the capstones overhang the wall less
than 3/4” [19mm] or under stairs where the tread overhangs the riser
less than 3/4” (19mm).
5. Wiring connections must be made with UL listed wire connectors that is
suitable for outdoor use.
6. Position the low voltage wire and UL listed wire connector so that it is
located within 6 inches (15.2 cm) from a building structure, a luminare,
or tting.
7. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
- 2 -
Product Dimensions
Package Contents
A. (1) Luminaire
B. (2) Stainless Steel Screws
19”
- 3 -
Install Mounting Plate
1
Optional: Install Glare Guard Before Installation
Install Luminaire in Brick or Masonry Wall
If you choose, you can attach the
glare guard rst before mounting
the xture.
Use the screws and washers to
secure the glare guard onto the
xture. Tighten with a
screwdriver.
Screw
Washer
Brick or
Masonry Wall
Mounting Plate
Barrell Nut
Determine the desired location for
each luminaire before construction
of the wall is started.
Insert the stainless steel mounting
plate (sold separately), in between
the layers of hardscape material.
If preferred, use an adhesive or
mortar (sold separately), to secure
the luminaire in place.
Install Luminaire
2
Mounting Plate
Glare Guard
Luminaire
Mounting Screw
Route the luminaire wire
through the wall to the main
low voltage supply cable using
standard masonry procedures.
A “V” shaped notch can be cut
into the hardscape material
to aide in wire management.
Attach the glare guard and
the luminaire to the stainless
steel mounting plate by using
mounting screws (ships with
mounting plate).
www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 4 -
Wire Connection
3
VOLT® 18” High Output Brass Rotatable LED Hardscape Light
VHS-6719-25-BBZ
Adjust Lamp Direction
4
Strip both leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
* We recommend ace heat shrink style connectors for hardscape
connections.
Main Low Voltage
Supply Cable
Luminaire Wires
Wire Connectors
Set Screw Lamp
Using an Allen wrench, loosen the set screws on the ends of the
lamp and then rotate the lamp to the desired direction. Always
tighten the set screws after adjustments.
- 5 -
Install Luminaire in Railing, Deck Over-hang or Stair
Determine Luminaire Location
1
Self-tapping
Screw
Luminaire
Railing, Deck
over-hang or Stair
Mark
Install from Bottom Install from Side
Self-tapping
Screw
Luminaire
Mark
Wireway
Slot
Railing, Deck
over-hang or Stair
Wireway Slot
Determine the desired location for the luminaire.
Place the luminaire to the mounting surface and mark two points
on the mounting surface where the holes are on the ends of the
luminaire. The marks will be used for self-tapping screws or wall
anchors.
Note: Wall anchors are required for certain installation conditions
(brick wall, concrete wall, etc.)
A wireway hole may be drilled through the decking fascia or other
surface adjacent to the mounting surface.
A. Hold the luminaire in the desired mounting location. Mark the
location where the wire exits the luminaire.
B. Drill a hole through surface (suggested 1/4” [6.5mm] hole).
C. Thread the wire through the drilled hole.
www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 6 -
VOLT® 18” High Output Brass Rotatable LED Hardscape Light
VHS-6719-25-BBZ
Install Luminaire
2
Self-tapping
Screw
Luminaire
Railing, Deck
over-hang or Stair
Mark
Install from Bottom Install from Side
Self-tapping
Screw
Luminaire
Mark
Wireway
Hole
Railing, Deck
over-hang or Stair
Wireway Hole
Glare Guard
Glare
Guard
Wall Anchor
Wall Anchor
Rubber
Washer
Install the luminaire and glare guard using provided self-tapping
screws. If the screws are dicult to install, mark holes and drill
1/8” pilot holes.
If wall anchors are required, drill proper holes from the marks on
the mounting surface and then insert the wall anchors. Then install
the luminaire and glare guard and secure them with the self-
tapping screws.
Rubber washers are required during installation from the side.
NOTE: DO NOT OVER TIGHTEN SCREWS.
Wire Connections
3
Strip both leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
* We recommend ace heat shrink style connectors for hardscape
connections.
Main Low Voltage
Supply Cable
Luminaire Wires
Wire Connectors
Adjust Lamp Direction
4
Set Screw Lamp
Using an Allen wrench, loosen the set screws on the ends of the
lamp and then rotate the lamp to the desired direction. Always
tighten the set screws after adjustments.
Install Luminaire toY Bracket
Determine Luminaire Location
1
Place the luminaire onto the
Y bracket using the rubber
washers and screws.Tighten
with a screwdriver.
Y Bracket
Luminaire
Screw
Rubber Washer
- 7 -
www.voltlighting.com
- 8 -
INSTALLATION INSTRUCTIONS
VOLT® 18” High Output Brass Rotatable LED Hardscape Light
VHS-6719-25-BBZ
Install Riser
2
Luminaire
Pass the supply wire from the
luminaire through the center
hole on the Y bracket and the
riser.Then thread the riser
onto the Y bracket and hand
tighten until snug.
Supply Wire
Supply Wire
Riser
Y Bracket
Install Stake
3
Determine the desired location
for mounting the stake. Hammer
the stake into the ground until
ange of stake is ush to grade.
To avoid damage to the stake,
place a board on top of the stake
while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
- 9 -
Intsall Riser to Stake
4
Supply Wire
Clear away area in the ground
at wireway slot on the top of
the stake. Pass the xture supply
wire through the center hole of the
stake and lay it into
the wireway slots.Thread the
riser onto the stake. Hand
tighten until snug.
Riser
Ground
Soil
Stake
Wire Connections
5
Strip both leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
* We recommend ace heat shrink style connectors for hardscape
connections.
Main Low Voltage
Supply Cable
Luminaire Wires
Wire Connectors
www.voltlighting.com
- 10 -
INSTALLATION INSTRUCTIONS
VOLT® 18” High Output Brass Rotatable LED Hardscape Light
VHS-6719-25-BBZ
Adjust Lamp Direction
6
Allen Wrench
Set Screw
Set Screw Lamp
Using an Allen wrench, loosen the set screws on the ends of the
lamp and then rotate the lamp to the desired direction. Always
tighten the set screws after adjustments.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Volt Illuminazione del paesaggio
Volt
Volt VAL-2101-0-BBZ Manuale utente
Volt
Volt VAL-2006-4-BBZ Manuale utente
Volt
Volt VHS-668-4-BBZ Manuale utente
Volt
Volt VDL-6008-4-BBZ Manuale utente
Volt
Volt VPL-1006 Manuale utente
Volt
Volt VWL-705-BBZ Manuale utente
Volt
Volt VPL-1048-4-BBZ Manuale utente
Volt
Volt VFL-4027 Manuale utente
Volt
Volt 3601 Series Manuale utente
Volt
Volt VPL-1011-4-BBZ Manuale utente
Volt
Volt VPL-3025 Series Manuale utente
Volt
Volt VPL-1001-4-BBZ Manuale utente
Volt
Volt VAL-2049-35-4-BBZ Manuale utente
Volt
Volt VFL-4601-4-BBZ Manuale utente
Volt
Volt VFL-4501-4-BBZ Manuale utente
Volt
Volt VSDL-6013-BBZ Manuale utente
Volt
Volt ShadowMaster VPL-1039 Manuale utente
Volt
Volt VHS-6719-BBZ Manuale utente
Volt
Volt VFL-4007-4-BBZ Manuale utente
Volt
Volt VAL-2015-BBZ Manuale utente
Manuali Illuminazione del paesaggio popolari di altre marche
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Manuale utente
Cooper Lighting
Cooper Lighting Invue 42 - 175W Manuale utente
Saxby Lighting
Saxby Lighting Islay 68784 Manuale
LIGMAN
LIGMAN EU-10016-3 Manuale utente
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza Manuale utente
LIGMAN
LIGMAN KI-60475 Manuale utente
