Vortex IMPACT 4000 Manuale di istruzioni
QUICK START MANUAL
IMPACT®4000
2 3
SPECIFICATIONS��������������������������������� 4
IMPACT®4000 BALLISTIC LASER RANGEFINDER ������� 6
PRODUCT WALKAROUND��������������������������� 7
BUTTON NAVIGATION ����������������������������� 8
BASIC OPERATION ������������������������������ 10
Battery Installation and Replacement����������������� 10
Power Up ������������������������������������ 11
Low Battery Icon ������������������������������� 11
Compass Calibration ���������������������������� 12
MOUNTING������������������������������������� 17
ZEROING �������������������������������������� 18
SETUP MENU ����������������������������������� 20
Range Mode Selection ��������������������������� 20
Target Mode Selection ��������������������������� 24
Profile Selection ������������������������������� 25
Range Cards ���������������������������������� 30
SETTINGS MENU �������������������������������� 32
Changing Settings on the Impact®4000 ��������������� 32
Backlight Selection ����������������������������� 33
Compass ������������������������������������� 33
Unit Selection ��������������������������������� 34
Auto-Shutoff Selection ��������������������������� 34
Visible Laser Selection ��������������������������� 35
Reset Selection �������������������������������� 35
Devices ������������������������������������� 36
CONNECTED DEVICES MENU����������������������� 36
Ballistics������������������������������������� 39
Weather ������������������������������������� 40
Wind���������������������������������������� 40
WEATHER INFORMATION ������������������������� 41
Wind Screen ���������������������������������� 41
Weather Screen�������������������������������� 43
Wind and Target Direction Screen ������������������� 43
RANGEFINDING TIPS����������������������������� 44
MAINTENANCE���������������������������������� 45
TROUBLESHOOTING GUIDE ������������������������ 46
Default Profiles �������������������������������� 48
INDEX ���������������������������������������� 48
TABLE OF CONTENTS
IMPACT®4000
4 5
SPECIFICATIONS
DISPLAY SIZE 1.3" (33mm)
DISPLAY TYPE LCD
DEER RANGE TREE RANGE
MAX
REFLECTIVE
RANGE
NORMAL MODE Up to 1200 yds.
(1097m)
Up to 2200 yds.
(2012m)
Up to 2400 yds.
(2195m)
ELR MODE Up to 1500 yds.
(1372m)
Up to 2500 yds.
(2286m)
Up to 4000 yds.
(3658m)
MINIMUM RANGE 5 yds. (4.5m)
ACCURACY
± 0.5 yds. @ < 100 yds.
± 1 yd. @ ≥100 yds. & ≤1000 yds.
± 3 yds. @ > 1000 yds.
MAX ANGLE READING ± 89˚
BATTERY TYPE CR123
LENGTH 4.6" (117mm)
HEIGHT 2.5" (64mm)
WIDTH 3.2" (81mm)
WEIGHT W/ BATTERY 16.0 oz. (453.6kg)
IMPACT®4000
6 7
IMPACT®4000
BALLISTIC LASER RANGEFINDER
The Impact®4000 takes the guesswork out of
long-range shooting with quick, accurate ballistic
corrections. Everything you need to generate point-
and-shoot target solutions without ever coming off the
gun. This advanced, rail-mounted laser rangefinder
delivers key range, ballistic, and weather data
via the integrated GeoBallistics®solver, on-board
Environmental Sensors, and our patented Wind
Bearing Capture Mode. Mounts to any picatinny-style
rail or rings with a diving board mount.
The Impact®4000 pairs, via Bluetooth®, with your
mobile device and the GeoBallistics®App. Scan the
QR code below to download the GeoBallistics®App
with your Apple or Android device.
The QR code below will also give access to
instructional videos.
SCAN QR CODE TO GET STARTED
PRODUCT WALKAROUND
Settings
Button
Environmental
Sensors
Picatinny Mount
& 1/2" Lug Nuts
Laser
Emitter/Receiver
Left Arrow Button Up Arrow Button
Down Arrow Button Right Arrow Button
Elevation Turret
Backlight Button
Windage Turret
Display Screen
Measure Button
Battery Compartment
Wind Bearing Capture
(W.B.C.) Button
Visible Laser
Enable/Disable Switch
Images are for representation only.
Product may vary slightly from what is shown.
IMPACT®4000
8 9
BUTTON NAVIGATION
SETTINGS
BUTTON • Opens and Closes the Settings Menu
WIND BEARING
CAPTURE BUTTON
• Opens and Closes the Wind Bearing
Capture Screen
MEASURE
BUTTON
• Takes Range
• Selects Menu Options
UP ARROW
BUTTON
• Navigates Up in Menu Structure
• Increases Manually Inputted Values
DOWN ARROW
BUTTON
• Navigates Down in Menu Structure
• Decreases Manually Inputted Values
LEFT ARROW
BUTTON
• Navigates Back in Menu Structure
• Navigates Left when Manually
Inputting Values
RIGHT ARROW
BUTTON
• Navigates Deeper into the Menu Options
• Navigates Right when Manually
Inputing Values
BACKLIGHT
BUTTON
BACKLIGHT
BACKLIGHTBACKLIGHT • Turns ON/OFF Display Backlight
Note: To change the orientation of the Arrow Buttons on the
Bluetooth®Remote, press and hold the button you wish to be
“Up” and the “Measure” button for three seconds until the
light blinks green.
IMPACT®4000 BUTTONS
Wind Bearing
Capture Button
(W.B.C.)
Backlight Button
Settings Button
Left Arrow Button
Up Arrow Button
Right Arrow Button
Measure Button
Down Arrow Button
BLUETOOTH® REMOTE BUTTONS
Up Arrow Button
Left Arrow Button
Measure Button
Right Arrow Button
Down Arrow Button
IMPACT®4000
10 11
BASIC OPERATION
Battery Installation and Replacement
To insert a new battery, flip up the finger tab on the
Battery Cap and unscrew, counterclockwise, to remove.
Insert a CR123 battery with the negative side (-) facing
outwards. Reinstall the Battery Cap and ensure it is
tightly closed.
To insert a battery into the
Bluetooth®Remote, utilize the
multi tool to unscrew the Battery
Cap counterclockwise, to remove.
Insert a CR2032 battery with the
positive side (+) facing outwards.
Reinstall the Battery Cap, turning
clockwise, and utilize the multi
tool to ensure it is tightly closed.
Power Up
Once the battery is installed, the Impact®4000 is in
ready condition – the normal power-off condition when
not ranging. To power up the Impact®4000 from ready
condition, press and release the “Measure” button.
The default ranging screen, HCD, will display. To turn
off the Impact®4000, press and hold the “Measure”
button for three seconds. The Impact®4000 Auto-
Shutoff default is three minutes. For instructions to
change the Auto-Shutoff to one minute or disable
Auto-Shutoff, see page 34.
Low Battery Icon
The Low Battery Icon
displays once the battery
reaches 20% life and stays
on until there is no power or
the battery is replaced.
IMPACT®4000
12 13
Compass Calibration
Compass calibration is important for the accuracy
of Wind Bearing Capture Mode. Read steps 1-5 of
“Calibrating the Compass and Inclinometer” section
before performing the following steps. The Impact®
4000 needs to be calibrated during initial setup and
should be re-calibrated every time you significantly
change location, typically 30 miles or more. Calibrate
your Impact®4000 outside and away from large metal
structures or objects.
Scan the QR Code below for links to video instructions
on how to calibrate the Impact®4000.
SCAN QR CODE TO GET STARTED
Important: Do not hit any buttons on the Impact®4000
during this process unless specifically instructed to do
so in the following steps.
Important: Remove the Impact®4000 from the rifle
before beginning the calibration process.
Calibrating the Compass and Inclinometer
To navigate to the Compass Screen, press the “Settings”
button. Navigate to and select “Settings” to open the
Settings Menu. Navigate to and select “Compass” to
open the Compass Screen. To begin calibration, select
“Calibrate” on the Compass Screen. Select “Begin” and
complete the following steps when prompted.
IMPACT®4000
14 15
1. Rotate the rangefinder in a figure eight for 15
seconds. Press the “Measure” button to continue.
2. Rotate the rangefinder horizontally for 15 seconds.
Press the “Measure” button to continue.
3. Rotate the rangefinder
vertically for 15 seconds.
Press the “Measure” button
to continue.
4. Turn the rangefinder onto its left side and rotate it
horizontally for 15 seconds. Press the “Measure”
button to continue.
5. Turn the rangefinder onto its right side and rotate
it horizontally for 15 seconds. Press the “Measure”
button to complete.
IMPACT®4000
16 17
MOUNTING
Once your Impact®4000 has been calibrated it can be
mounted to your weapon. Prior to mounting the laser
rangefinder ensure your riflescope is mounted and
zeroed to your desired zero distance.
1. Mount your picatinny diving board mount or
picatinny accessory rail and tighten to the
manufacturer’s torque specifications using a
torque wrench.
2. Place the Impact®4000 Picatinny Mount on
the rail and position it so its placement does not
interfere with the adjustment of the turrets.
3. Using the provided 1/2" Nut Diver Tool, tighten the
1/2" Lug Nuts to 45 in-lbs. Using a torque wrench
is recommended if available.
Note: If the Impact®4000 is mounted on the side of the gun,
the screen with auto-rotate accordingly.
The screen will read “Success” if the compass has
successfully calibrated. If the screens reads “Fail - Try
Again”, press the “Measure” button to restart the
calibration and repeat this process until the Impact®
4000 is successfully calibrated.
IMPACT®4000
18 19
ZEROING
To ensure the accuracy of the Impact®4000 range and
ballistic solutions it must be zeroed parallel to your
riflescope. This allows you to aim the device with the
center of your reticle at all distances. To zero, follow
the steps below:
1. Before starting, your riflescope must be properly
mounted and zeroed. Your Impact®4000 must be
calibrated and then mounted to your weapon.
2. Place the Small Reflective Target Sticker on the
Alignment Target at the same measured offset
that the Impact®4000 is mounted from the
center of the riflescope. Find common mounting
offsets marked on the Alignment Target. Your
offset may be different, it is good to measure left/
right and up/down offset to the nearest 1/4" to
verify the sticker placement.
Height Over Scope Center = Rangefinder Offset
REFLECTIVE TAPE
REFLECTIVE TAPE
Note: The Alignment Target grid consists of 1" squares for
easy measurements.
3. Hang the Alignment Target, in a safe direction,
at 50-100 yards using the Large Reflective Tape
Strips. Use one piece of tape on the top of the
target and one on the side of the target.
4. Turn the Visible Laser Switch on the side of the
laser rangefinder to “Enable” utilizing the provided
Torx®T-10 Tool.
5. Turn the Visible Laser ON from the Settings Menu.
To do so, press the “Settings” button. Navigate
to and select “Settings”. Navigate to and select
“Visible Laser” and select “ON”.
Note: While the Visible Laser is ON, all ranging and
ballistic functions are disabled.
6. Utilize the Large Reflective Tape Strips to locate
the target with the Visible Laser. The Visible Laser
may not be well aligned to start.
7. Align your riflescope’s crosshair to the center dot
of the Alignment Target, and use the Flat Head
Tool to adjust the Elevation and Windage Turrets
to align the Visible Laser to the Small Reflective
Target Sticker.
8. Your Impact®4000 is now zeroed parallel to
your riflescope.
9. Turn the Visible Laser Switch on the side of
the laser rangefinder to “Disable” utilizing the
provided Torx®T-10 Tool and turn the Visible
Laser OFF from the Settings Menu following the
instructions from Step 5.
Once the Impact®4000 is calibrated, mounted, and
zeroed it must be setup to your specifications to ensure
accurate ballistic solutions for your shooting scenario.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Vortex Strumento di misura
Vortex
Vortex Diamondback HD 2000 Manuale utente
Vortex
Vortex Viper HD 3000 Manuale utente
Vortex
Vortex Razor HD 4000 GB Manuale di istruzioni
Vortex
Vortex Impact 850 Manuale utente
Vortex
Vortex BLUEONE BWO 155ZM Manuale utente
Vortex
Vortex Ranger 1500 Manuale utente
Vortex
Vortex Ranger 1000 Manuale utente
Vortex
Vortex Razor HD 4000 GB Manuale utente
Vortex
Vortex Razor HD 4000 Manuale utente
Vortex
Vortex RWG Series Manuale utente
