Wasp WWS150i Manuale utente

WWS150i

Table of Contents

Chapter 1 Introduction 2

Chapter 2 Barcode Symbologies 3

Chapter 3 Quick Start 4

Chapter 4 WWS150i Setup & Configuration 6

1. Setup & Configuration 6

2. Factory Default and Autosense Stand Mode 6

3. Connection and Scan Options 7

4. Start and Stop Pin 8

5. Interface Settings 9

6. Memory Mode 10-12

7. Beep Settings 13

8. iOS Hotkey 14

9. Set Scanner 1D 15

10. Beep Delay and Caps Lock 16

11. Language and Preamble/Postamble 17

12. Terminator/Code ID 18

13. Enable/Disable Barcode Symbologies 19

Code 39 and Interleaved 2 of 5 Settings 20

Code 93 and MSI Plessey Settings 21

Code 128 and UCC/EAN 128 Settings 22

Codabar and UPC-A Settings 23

UPC-A Supplement Settings / UPC-A to EAN-13/UPC-E Settings 24

UPC-E Supplement/EAN-8 Settings 25

EAN-8 Supplemental and EAN-13 Settings 26

EAN-13 Supplemental Settings 27

Chapter 5 Bluetooth Settings 28

Appendix A Barcode Test Symbols 29-30

Appendix B ASCII Table 31-34

Appendix C Function Codes for PC 35

Appendix D Technical Specifications 36

Appendix E Warranty Information 37

FAQ 38

Product Support 39

Chapter 1

Introduction

Barcoding is the most common Automated Data Collection (ADC) technology. It provides timely, error-free information that

can be used to increase productivity, accuracy, and efficiency in the workplace. Virtually every type of industry is using

barcodes to replace keyboard data entry. Studies have shown that a proficient data entry operator will make one error for every

300 characters that are manually entered. The error rate using barcodes is negligible and can be error-free using barcode

symbologies with the check digit enabled.

The Wasp Charged Coupled Device (CCD) technology is a technique whereby a barcode is photographed, digitized, and

electronically sampled by built-in photodetectors. The detectors process the measurement of every bar and space using the

number of adjacent photodetectors which contrast a black mark and a white space. Of all the hand-held barcode scanning

devices on the market, the CCD reader is the easiest to use and most cost effective for the typical business user.

The Wasp WWS150i Scanner is an extended distance scanner with a depth of reading of up to one foot depending on the mil size

of the barcode. To activate the scanner, the user simply points the scanning aperture towards the barcode, pulls the trigger, and

aims the red LED beam across the barcode.

Chapter 2

Barcodes are symbols consisting of a series of bars and spaces which can be applied to packages, cartons, bottles, and other

commercial products. The bars and spaces in each symbol are grouped in such a way to represent a specific ASCII character

or function. The interpretation of these groups is based on a particular set of rules called symbologies. Various symbologies

have been developed for particular applications. Some examples are shipping and receiving, manufacturing, retail, healthcare,

transportation, document processing and tracking, and libraries.

The resolution of a barcode is dependent on the narrowest element of a barcode (X dimension), and can vary from high density

(nominally less than 0.009 in./0.23 mm), medium density (between 0.009 in./0.23 mm and 0.020 in./0.50 mm), and low density

(greater than 0.020 in./0.50 mm). Medium and low densities are the most common since these are the easiest to read (scan)

with nearly all scanning devices. The Wasp WWS150i scanner can read barcodes with X-dimensions as low as 5 mils (0.005

in/0.13mm).

The Wasp WWS150i Scanner can read the most popular barcode symbologies including Code 39, Code 93, Code 128, Interleaved

2 of 5, UPC-A, UPC-E, EAN/JAN-8, EAN/JAN-13, Codabar, and MSI/Plessey.

Please see test chart on pages 26-27.

Barcode Symbologies

Chapter 3 QUICK START

Quick Start

1. Unpack.

Open the box and remove all the pieces from their protective packaging.

2. Charging the WWS150i.

You must charge the scanner for 4 hours before first using it. To charge the

scanner plug the power supply in to the bottom of the scanner.

3. Setting up Bluetooth.

If you already have Bluetooth setup on your PC or device, please continue

to the next step.

To setup Bluetooth on your PC you will need to insert the CD with the Bluetooth software on it. Follow the instruction on the CD

for installing the Bluetooth software.

4. Connecting the scanner to a Bluetooth device.

The scanner will connect to most Bluetooth devices that support HID connection.

You will need to open your Bluetooth software and search for Bluetooth devices. The Bluetooth software can be found by clicking

the Bluetooth symbol on the start bar near the computer time. If the Bluetooth symbol is

not found, there could be a problem

with the Bluetooth installation.

Once you have the Bluetooth software open you will need to scan the Set Connection

barcode (pg 7). This will make the scanner

ready

to be detected by the Bluetooth software.

The following screens are Microsoft’s standard Bluetooth wizard.

*Most Bluetooth wizards will have similar steps. Instructions for XP users are displayed below. Instructions for Win7 users

begin on page 5

Check the “My device is setup and ready to be found.” and click Next.

The scanner will show up in the list of Bluetooth devices found. Select the Wasp Barcode Bluetooth

Keyboard and click Next.

If Wasp Barcode Bluetooth Keyboard does not show up in the available devices please check the

following:

1. Make sure the scanner is on by pressing the trigger.

2. If you are using a pre-installed Bluetooth

adapter, make sure the adapter supports HID.

The next step will ask you to setup a passkey for the device. By default the scanner will not have a

passkey set. Please select “Don’t use a passkey” and click Next.

You can set a passkey later if you prefer,see Start/Stop Pin on page 8 for details.

Chapter 3

LED Light Indicator

Scan/Wake Scanner (After Idle)

Toggle Keyboard On/Off & Connect Via BT

Cable/Charge Port

The Complete Wizard screen appears. Just click Finish to complete.

Once the wizard is complete the scanner will show up as a Wasp Keyboard. Click OK to close the

screen. You are now ready to use the WWS150i.

(XP Instructions, cont.)

Win7 Instructions

On the Add a Device screen, select Wasp Barcode. Click the Next button.

Enter the Pairing Code provided into your mobile device. Once the PC detects the pairing code

has been entered and a connection has been established, the Next button will become enabled.

Click

Next to contine.

You can verify that your device has been added by clicking the Devices and Printers link on the

screen. Click Close to close the connection wizard.

QUICK START

Chapter 4

SETUP AND CONFIGURATION/FACTORY DEFAULT/AUTOSENSE STAND MODE

Use the Factory Default barcode to reset the scanner to the Default settings.

Factory Default

Autosense Flash Mode Enable

Scan this Autosense Stand Mode barcode to enable the hands-free autosense feature of the WWS150i Scanner. If you desire to turn this mode “off,”

please scan the default barcode above.

Autosense Stand Mode

In order to configure the Wasp WWS150i Scanner, you must familiarize yourself with the setup procedures on the following pages.

The default settings of the scanners are identified on each page and clearly marked using an asterisk (*). The default settings have

been preprogrammed for the most common barcode configurations. Use the setup & configuration barcodes only to customize the

WWS150i Scanner settings. If you need to configure the Scanner, the default settings will be overwritten. All the programmed settings

are stored permanently in non-volatile memory.

In order to configure the Wasp WWS150i Scanner, two basic steps need to be followed:

(1) Locate the group that contains the options to be changed.

(2) Scan the barcode representing the option to be changed. The scanner will sound two beeps.

To change Minimum/Maximum Length:

(1) Scan the Minimum or Maximum Length barcode associated with the symbology.

(2) Scan a 2 digit value from the ASCII table on pages 28-31.

(3) Scan the Minimum or Maximum Length barcode again.

Example: To have a minimum length barcode of 1, you must scan a 0 then 1, then scan the minimum barcode again. To have a

maximum length barcode of 10, you must scan a 1 then 0, then scan the maximum barcode again.

Setup & Configuration

Factory Default

Note: Enabling this option will significantly increase the WWS150i Scanners battery consumption.

Chapter 4

CONNECTION AND SCAN OPTIONS

Check Version

Scan the Check Version barcode to verify your current firmware’s version number.

Check Version

The Link Quality affects the transmission quality. When Link Quality is turned on (default setting), data transfer is more secure, but

slower. If you notice that your transmissions to the host are too slow, you can try turning the Link Quality setting to off.

Link Quality On/Off

Link Quality On Link Quality Off

Set Connection

Scan this barcode to break your current connection and enable your device to connect to a new Bluetooth host.

Set Connection

Bluetooth SPP (Bluetooth COM)

The Bluetooth SPP (Serial Port Protocol) creates a virtual Bluetooth comport. This setting is not recommended. Only use this option if

you have software capable of capturing data off of a comport.

Bluetooth SPP (Bluetooth COM)

Bluetooth HID

Use this setting (on by default) to pair with most Bluetooth connections. Bluetooth HID works just like a keyboard..

Bluetooth HID

Chapter 4

CONNECTION AND SCAN OPTIONS

Start and Stop Pin

Use the Start and Stop Pin barcodes when you are prompted for a password during Bluetooth pairing. To use this setting:

1. When prompted for a password, scan the Start Pin barcode

2. Scan the appropriate numbers (provided below) for your password.

3. Scan ENTER.

4. Scan the Stop Pin barcode.

Now the Pin is set and the scanner should pair to the PC. Test the connection by scanning a barcode from WordPad, NotePad or the

equivalent and verifying the scan is correct.

Start Pin Stop Pin

ENTER

Scan the numbers for your password, then scan ENTER.

Chapter 4

INTERFACE SETTINGS

Scan any one of the barcodes below to reset the scanner back to the desired interface:

*To retrieve stored data, connect the scanner to the host with the cable, access removable storage device “Miniscan” from which you may open or

copy the file “Barcode.txt” to your computer.

To exit memory mode, scan any interface barcode in the “interface” section of the manual.

Altri manuali per WWS150i

Indice

Altri manuali Wasp Lettore di codici a barre

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente