Wasp WWS550i Manuale utente
1
WWS550i
Quick Start Guide
This page is intentionally left blank
Table of Contents
Quick Start 2
1. Unpack 2
2. Charging the WWS550i 2
3. Setting up the Bluetooth Adapter 2
4. Connecting the Scanner to a Bluetooth Device. 2
Setup & Configuration 6
Factory Default 7
Check Version 7
Link Quality On/Off 7
Set Connection 7
Bluetooth SPP (Bluetooth COM) 8
Bluetooth HID (Keyboard) 8
Start and Stop Pin 8-9
Terminator 10
iPad/iPhone Toggle Keyboard 10
Enable/Disable iOS Hotkeys 11
Secure Simple Pairing 11
Rev4/23/2014
QSG
4
QSG
4
Quick Start
1. Unpack
Open the box and remove all the pieces from their protective packaging.
2. Charging the WWS550i
You must charge the scanner for 4 hours before first using it. To charge
the scanner, plug the power supply into the bottom of the scanner.
3. Setting up the Bluetooth Adapter
If you already have Bluetooth setup on your PC or device, please continue
to the next step.
To setup Bluetooth on your PC, you will need to insert the Bluetooth
adapter into an available USB port. Windows will detect the adapter and
install the required Microsoft Bluetooth software. If Windows does not
detect the Bluetooth adapter, please remove the adapter and insert the CD
with the adapter’s Bluetooth software on it. Follow the instructions on the
CD for installing the Bluetooth software.
4. Connecting the scanner to a Bluetooth device
The scanner will connect to most Bluetooth devices that support HID
connection.
You will need to open your Bluetooth software and search for Bluetooth
devices. The Bluetooth software can be found by clicking the Bluetooth
symbol on the start bar near the computer time. If the Bluetooth symbol is
not found, there could be a problem with the Bluetooth adapter installation.
QSG
4 5
QSG
54
Check the “My device is setup and
ready to be found” checkbox and click Next.
The scanner will show up in the list of
Bluetooth devices found. Select
Wasp Barcode and click Next.
If Wasp Barcode does not show up in the
available devices, check the following:
1. Make sure the scanner is on by pressing
the trigger.
2. If you are using a pre-installed Bluetooth
adapter, make sure the adapter supports HID.
Windows XP Bluetooth Pairing
Scan the following three barcodes:
1. Factory Default - page 7
2. Bluetooth HID - page 8
3. Set Connection - page 7
The next step will ask you to setup a passkey
for the device.
Select “Choose a passkey for me”, then click
the Next button. Your passkey will appear on
the resulting screen.
QSG
6
The Complete Wizard screen appears. Click
Finish to complete.
When the wizard is complete, the scanner
will show up as a Wasp Keyboard. Click OK
to close the screen. You are now ready to
use the WWS550i.
Scan the following barcodes found on page 9:
Note: Maintain a brisk pace when scannng these codes, as Windows
provides a short time for entering them.
1. Start PIN
2. Each digit of the code (for code 1549 scan the barcode for 1, then the
barcode for 5, etc.)
3. Enter
4. Stop PIN
Windows 7 Bluetooth Pairing
1. Click the Start icon, then type “bluetooth”
in the Search field.
2. Click “Add a Bluetooth device” from the
resulting menu choices.
3. Scan the following three barcodes:
A. Factory Default - page 7
B. Bluetooth HID - page 8
C. Set Connection - page 7
QSG
QSG
6 7
4. Click Wasp Barcode Bluetooth Keyboard,
then click the Next button.
5. Scan the following barcodes found on
page 9:
Note: Maintain a brisk pace when scannng
these codes, as Windows provides a short
time for entering them.
A. Start PIN
B. Each digit of the code (for code 1549...
scan the barcode for 1, then the barcode for
5, etc.)
C. Enter
D. Stop PIN
6. A screen will appear confirming you have
successfully added the scanner.
When the wizard is complete, the scanner
will show up as a Wasp Keyboard. Click OK
to close the screen. You are now ready to
use the WWS550i.
QSG
Troubleshooting: If the device does not pair, click Back and repeat steps
3-6. Do not omit scanning the Stop Pin barcode in Step 5, even if you
see a message on screen about installing device drivers or that pairing is
complete.
If the device repeatedly fails to pair, it may be stuck in a partially-installed
state. Go to Start > Devices > Printers. In the Devices section, look for
a Wasp Keyboard (or similar name). Right-click it, then click Remove
Device. When complete, start the Pairing procedure again.
To test the connection, open Notepad, MS Word or another application
that accepts text input from a keyboard, then scan a barcode. You can
try the Test Symbols in the scanner manual, or a UPC barcode from a
product. The application should show the data from the barcode.
QSG
8
In order to configure Wasp WWS550i Freedom Scanner, familiarize
yourself with the setup procedures on the following pages. The default
settings of the scanners are identified on each page and clearly marked
using an asterisk (*). The default settings have been preprogrammed for
the most common barcode configurations. Use the setup & configuration
barcodes only to customize the WWS550i Freedom Scanner settings. If
you need to configure the Scanner, the default settings will be overwritten.
All the programmed settings are stored permanently in non-volatile
memory.
In order to configure Wasp WWS550i Freedom Scanner,
two basic steps need to be followed:
(1) Locate the group that contains the options to be changed.
(2) Scan the barcode representing the option to be changed.
The scanner will sound two beeps.
Setup & Configuration
QSG
98
Use the Factory Default barcode to reset the scanner to the Default settings.
Factory Default
Check Version
Scan the Check Version barcode to verify your current firmware’s version number.
Check Version
Factory Default
Link Quality affects the transmission quality. When Link Quality is turned
on (default setting), data transfer is more secure, but slower. If you notice
that your transmissions to the host are too slow, you can try turning the
Link Quality setting to off.
Link Quality On/Off
Link Quality On* Link Quality Off
Set Connection
Scan this barcode to break your current connection and enable your device
to connect to a new Bluetooth host.
Set Connection
QSG
10
Bluetooth SPP (Bluetooth COM)
The Bluetooth SPP (Serial Port Protocol) creates a virtual Bluetooth
comport. This setting is not recommended. Only use this option if you
have software capable of capturing data off of a comport.
Bluetooth SPP (Bluetooth COM)
Bluetooth HID
Use this setting (on by default) to pair with most Bluetooth connections.
Bluetooth HID works just like a keyboard.
Bluetooth HID*
Start and Stop Pin
Use the Start and Stop Pin barcodes when you are prompted for a password
(Passkey) during Bluetooth pairing. To use this setting:
1. When prompted for a password, scan the Start Pin barcode.
2. Scan the appropriate numbers (provided on page 9) for your password.
3. Scan ENTER.
4. Scan the Stop Pin barcode.
Now the Pin is set and the scanner should pair to the PC. Test the
connection by scanning a barcode into WordPad, NotePad or the equivalent
and verifying the scan is correct.
Altri manuali per WWS550i
1
Indice
Altri manuali Wasp Lettore di codici a barre
Wasp
Wasp WWS450 Manuale utente
Wasp
Wasp Bar Code Laser Istruzioni operative
Wasp
Wasp CCD - 80SIR Manuale utente
Wasp
Wasp WDT 3200 Manuale di installazione e funzionamento
Wasp
Wasp WWS650 Guida per l'amministratore
Wasp
Wasp WWS800 Manuale utente
Wasp
Wasp WLS9600 Manuale utente
Wasp
Wasp WPS1500 Manuale utente
Wasp
Wasp CCD Scanner Istruzioni operative
Wasp
Wasp WWS750 Manuale utente
Wasp
Wasp WPL618 Series Manuale utente
Wasp
Wasp WPL308 Manuale utente
Wasp
Wasp WLR8950 Manuale utente
Wasp
Wasp WLP 4170 Istruzioni operative
Wasp
Wasp WDI4600 Manuale utente
Wasp
Wasp WWS150i Manuale utente
Wasp
Wasp WPL610 Manuale utente
Wasp
Wasp WLR8900 Istruzioni operative
Wasp
Wasp WLR8950 Manuale utente
Wasp
Wasp WLP 4170 CCD Istruzioni operative
Manuali Lettore di codici a barre popolari di altre marche
POSMicro
POSMicro Datalogic PowerScan D7100 Manuale utente
Marson
Marson MT780 Guida rapida alla configurazione
NCR
NCR RealPOS Manuale utente
Motorola
Motorola SE3300 Guida rapida alla configurazione
Element
Element P130BT Manuale utente
Motorola
Motorola Symbol LS3008 Manuale di installazione e funzionamento
