Wasp WWS150i Manuale utente

1

WWS150i

Quick Start Guide

Table of Contents

Quick Start 2

1. Unpack 2

2. Charging the WWS150i 2

3. Connecting the Scanner to a Bluetooth Device 2

Setup & Configuration 3

Factory Default 4

Check Version 4

Link Quality On/Off 4

Set Connection 4

Bluetooth SPP (Bluetooth COM) 5

Bluetooth HID (Keyboard) 5

Terminator 6

iPad/iPhone Toggle Keyboard 6

Enable/Disable iOS Hotkeys 7

QSG

2

QSG

2

Quick Start

1. Unpack

Open the box and remove all the pieces from their protective packaging.

2. Charging the WWS150i

You must charge the scanner for 4 hours before first using it. To charge

the scanner, plug the power supply into the bottom of the scanner.

3. Connecting the scanner to a Bluetooth device

The scanner will connect to most Bluetooth devices that support HID

connection.

You will need to open your Bluetooth software and search for Bluetooth

devices. The Bluetooth software can be found by clicking the Bluetooth

symbol on the start bar near the computer time.

QSG

2 3

QSG

2

In order to configure Wasp WWS150i Freedom Scanner, familiarize

yourself with the setup procedures on the following pages. The default

settings of the scanners are identified on each page and clearly marked

using an asterisk (*). The default settings have been preprogrammed for

the most common barcode configurations. Use the setup & configuration

barcodes only to customize the WWS150i Freedom Scanner settings. If

you need to configure the Scanner, the default settings will be overwritten.

All the programmed settings are stored permanently in non-volatile

memory.

In order to configure Wasp WWS150i Freedom Scanner,

two basic steps need to be followed:

(1) Locate the group that contains the options to be changed.

(2) Scan the barcode representing the option to be changed.

The scanner will sound two beeps.

Setup & Configuration

QSG

4

Use the Factory Default barcode to reset the scanner to the Default settings.

Factory Default

Check Version

Scan the Check Version barcode to verify your current firmware’s version number.

Check Version

Factory Default

Link Quality affects the transmission quality. When Link Quality is turned

on (default setting), data transfer is more secure, but slower. If you notice

that your transmissions to the host are too slow, you can try turning the

Link Quality setting to off.

Link Quality On/Off

Link Quality On* Link Quality Off

Set Connection

Scan this barcode to break your current connection and enable your device

to connect to a new Bluetooth host.

Set Connection

QSG

54

Bluetooth SPP (Bluetooth COM)

The Bluetooth SPP (Serial Port Protocol) creates a virtual Bluetooth

comport. This setting is not recommended. Only use this option if you

have software capable of capturing data off of a comport.

Bluetooth SPP (Bluetooth COM)

Bluetooth HID

Use this setting (on by default) to pair with most Bluetooth connections.

Bluetooth HID works just like a keyboard.

Bluetooth HID*

QSG

6

Terminator

The ‘Terminator’ option is used to specify the end-of-text message and is

primarily used to denote the end of the barcode value.

CR *

None

LF

CR + LF

TAB

Space

ESC

iPad/iPhone Toggle Keyboard

Scan this barcode to display or hide the on-screen keyboard when

connected to an iPad or iPhone.

iPad/iPhone Toggle Keyboard

QSG

7

connection

6

Enable/Disable iOS Hotkey

Use these barcodes to enable or disable the iOS hotkey on your device.

When the iOS hotkey is enabled, you can double-click the trigger to toggle

the iPhone/iPad Touch Keyboard.

Enable iOS Hotkey

Disable iOS Hotkey

*

8

Wasp®Barcode Technologies

1400 10th Street, Plano, Texas 75074

Tel: 214.547.4100 • Fax: 214.547.4101

www.waspbarcode.com

Altri manuali per WWS150i

1

Indice

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente