WEIHONG NK300CX Manuale utente
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
1/ 53
NK300CX CNC Integrated System
Getting Started
Version: 2019.04 17 Version
Author: Document Department
Weihong Corporation, All Rights Reserved
1 System Overview ............................................................................................................................3
1.1 NK300CX Host.....................................................................................................................3
1.2 WH106C Operation Panel and WH201C Keypad Panel ......................................6
1.3 WH108C Operation Panel............................................................................................ 10
1.4 WH208A1 Operation Panel......................................................................................... 13
1.5 NK300CX Connection Diagram.................................................................................. 18
1.6 Main Software Interface ............................................................................................... 21
2 Basic Commissioning ................................................................................................................. 22
2.1 Switch the System Configuration.............................................................................. 22
2.2 Adjust I/O Port Polarity................................................................................................ 23
2.3 Set Commissioning Parameters................................................................................. 25
2.4 Adjust the Axis Direction ............................................................................................. 28
2.5 Return to the Machine Origin..................................................................................... 29
2.6 Set the Workbench Travel ........................................................................................... 31
3 Quick Start...................................................................................................................................... 32
3.1 Load a Program File ....................................................................................................... 32
3.2 Execute Tool Calibration.............................................................................................. 37
3.3 Adjust the WCS................................................................................................................. 41
3.4 Define the Workpiece Origin ...................................................................................... 43
3.5 Select Tools for Machining .......................................................................................... 45
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
2/ 53
3.6 Execute Selective Machining....................................................................................... 47
3.7 Execute Machining.......................................................................................................... 49
4 FAQs (Operator)........................................................................................................................... 50
4.1 Failed to Register the System ..................................................................................... 50
4.2 Tool Calibration Overtravel Alarm........................................................................... 51
4.3 Z-axis Overtravel Protection....................................................................................... 51
5 FAQs (Manufacturer) ................................................................................................................. 52
5.1 Axis Servo Alarm ............................................................................................................. 52
5.2 Failed to Register the System ..................................................................................... 52
5.3 Drive 400 Alarm .............................................................................................................. 53
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
3/ 53
1System Overview
NK300CX Integrated CNC System (Hereinafter referred as to NK300CX) consists
of hardware and software:
Hardware
•NK300CX host
•Operation panel and keypad panel
–NK300CX-H: WH106C operation panel and WH201C keypad panel
–NK300CX-V: WH108C operation panel
–NK300CX for Frilling: WH208A1 operation panel
•Lambda terminal board
It varies with axes configuration and software functions:
–Lambda 4S: pulse-type, up to 4 axes supported.
–Lambda 5S: pulse-type, up to 5 axes supported.
–Lambda 5E: pulse-type, up to 5 axes and absolute function supported.
–Lambda 5M: bus-type, up to 8 axes and absolute function supported.
•DB9M/F cables
See NK300CX Connection Diagram for how to connect all hardware.
Software
Based on an embedded platform, NK300CX software can be divided into the
following:
•Integral software: combine configurations of 3 axes, 4 axes, and 5 axes as a
whole.
•Multi-Z axes software: used for motion control of multi-Z axes, including
linkage configuration, double Y linkage configuration and alternative
configuration.
This section takes integral software under three-axis configuration as an
example.
See Main Software Interface for the introduction for its main software interface.
1.1NK300CX Host
This part introduces the layout and mounting dimension of NK300CX host.
1.1.1 Layout
It introduces the layout of both front view and rear view.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
4/ 53
1.1.1.1 Front View
The front view of NK300CX host is as follows:
1. USB interface
Used to connect with USB flash disks. And it is protected by a cover.
2. Display area
Human-machine interface, or user’s interface. It is user-friendly and ease of use.
3. Functional keys
There are altogether 6 functional areas, including Gen. (machining), Adv.
(advanced), Prog. (program), Sys (system), Para. (parameter) and Diag.
(diagnosis) keys.
You can access the functional area by directly pressing corresponding key.
4. Operation keys
Including keys from F1 to F8, and page turning keys.
Used to activate the functions indicated by the soft keys, and turn to previous
page or next page.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
5/ 53
1.1.1.2 Rear View
The rear view of NK300CX host is as follows:
1. DB9M/F cable interface
–For NK300CX-H, it is used to connect with the keypad panel.
–For NK300CX-V, it is used to connect with the operation panel.
2. Terminal board interface
Used to connect with Lambda terminal board.
3. VGA interface
Used to connect with VGA devices, which are not needed under general
situation.
4. LAN interface
Used to connect with network, with 100Mbps transmission rate.
5. USB interface
Two USB interfaces, which are used to connect with USB flash disks.
6. Power interface
Used to connect with 220V power supply.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
6/ 53
1.1.2 Mounting Dimension (Unit: mm)
NK300CX Dimension
NK300CX Cut-out
1.2WH106C Operation Panel and WH201C Keypad Panel
This part introduces the layout and mounting dimension of WH106C operation
panel and WH201C keypad panel used by NK300CX-H.
1.2.1 Operation Panel
This part introduces the layout and mounting dimension of WH106C operation
panel.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
7/ 53
1.2.1.1 Layout
The front view of the operation panel is as follows:
1. USB interface
Used to connect with USB flash disks.
2. E-stop switch
Used to stop the machine tool completely when the machine tool is in danger by
triggering the E-stop alarm, so as to protect the operator and machine tool.
After danger is cleared, you can remove the E-stop alarm by rotating the switch
in the clockwise direction.
3. Spindle override knob
Used to adjust spindle override from 50% to 150%.
4. Keys for mode selection
Used to select a machining mode among Auto, JOG, Handle, Step and
REF.Point.
JOG, Handle, Step are referred as Manual mode.
5. Feed override knob
Used to adjust feed override from 0 to 120%.
6. Axis direction keys
Used to manually move each axis.
In Manual mode:
–Press an axis direction key and Rapid key. The machine tool moves at
rapid jog speed.
–Press an axis direction key. The machine tool moves at jog speed.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
8/ 53
7. Keys for common operations
Used to execute common operations, including Simulate, Single Block, Handle
and Reset keys.
8. Spindle control keys
Used to control spindle movement, including CW, Stop and CCW keys.
9. Extension keys
Used to customize extension functions, including K1, K2, K3 and K4 keys.
10. Keys for common ports
Used to turn on or turn off frequently used ports.
11. Keys for movement control
Used to control the movement of the machine tool, including START, STOP,
Pause, and Resume keys.
See Execute Machining for details.
12. Power Switch
Used to control power on or off.
1.2.1.2 Mounting Dimension (Unit: mm)
WH106C Dimension
WH106C Cut-out
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
9/ 53
1.2.2 Keypad Panel
This part introduces the layout and mounting dimension of WH201C keypad panel.
1.2.2.1 Layout
The front view of the keypad panel is as follows:
1. Alpha-numeric keys
2. Direction keys
3. System operation keys
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD
10 / 53
1.2.2.2 Mounting Dimension (Unit: mm)
WH201C Dimension
WH201C Cut-out
1.3WH108C Operation Panel
This part introduces the layout and mounting dimension of WH108C operation
panel used by NK300CX-V.
Altri manuali per NK300CX
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali WEIHONG Sistema di controllo
WEIHONG
WEIHONG NcEditor V12 Manuale utente
WEIHONG
WEIHONG NK280B Manuale utente
WEIHONG
WEIHONG NK105 Manuale utente
WEIHONG
WEIHONG NK105 G2F Manuale utente
WEIHONG
WEIHONG NC65C Manuale utente
WEIHONG
WEIHONG NK300CX Manuale utente
WEIHONG
WEIHONG NCStudio V12 Manuale utente
WEIHONG
WEIHONG PM53B Manuale utente
WEIHONG
WEIHONG 200 Series Manuale utente
WEIHONG
WEIHONG NK200 Manuale utente
