Wen 10130 Manuale utente

130-FOOT LASER

DISTANCE MEASURE

Instruction Manual

IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability,

ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged,

trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions. If you use

your tool properly and for its intended purpose, you will enjoy years of safe, reliable service.

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

TECHSUPPOR[email protected]1-800-232-1195 (M-F 8AM-5PM CST)

For replacement parts and the most up-to-date instruction manuals, visit WENPRODUCTS.COM

MODEL 10130

CONTENTS

WELCOME 3

Introduction ..................................................................................................... 3

Speciﬁcations................................................................................................... 3

SAFETY 4

General Safety Rules........................................................................................ 4

BEFORE OPERATING 6

Know Your Laser Distance Measure..................................................................6

Assembly & Adjustments................................................................................. 7

OPERATION & MAINTENANCE 7

Operation ......................................................................................................... 7

Maintenance....................................................................................................11

Troubleshooting Guide................................................................................... 12

Exploded View & Parts List.............................................................................13

Warranty Statement ........................................................................................14

SPECIFICATIONS

INTRODUCTION

Thanks for purchasing the WEN Laser Distance Measure. We know you are excited to put your tool to work, but ﬁrst,

please take a moment to read through the manual. Safe operation of this tool requires that you read and understand

this operator’s manual and all the labels afﬁxed to the tool. This manual provides information regarding potential

safety concerns, as well as helpful assembly and operating instructions for your tool.

NOTE: The following safety information is not meant to cover all possible conditions and situations that may occur.

WEN reserves the right to change this product and speciﬁcations at any time without prior notice.

At WEN, we are continuously improving our products. If you ﬁnd that your tool does not exactly match this manual,

please visit wenproducts.com for the most up-to-date manual or contact our customer service at 1-800-232-1195.

Keep this manual available to all users during the entire life of the tool and review it frequently to maximize

safety for both yourself and others.

Indicates danger, warning, or caution. The safety symbols and the explanations with them deserve your

careful attention and understanding. Always follow the safety precautions to reduce the risk of ﬁre, electric shock

or personal injury. However, please note that these instructions and warnings are not substitutes for proper ac-

cident prevention measures.

Model Number 10130

Laser Type 650 nm, <1 mW

Laser Class II

Battery AAA Batteries (2) (Not Included)

Operating Temperature 14°F - 104°F

Measuring Distance 0.16 ft. - 130 ft.

Measuring Accuracy +/- 5mm at 130 feet

+/- 3mm at 65 feet

Product Weight 3.5 oz. (With Batteries)

Product Dimensions 1-5/8 in. x 1 in. x 4-3/8 in.

GENERAL SAFETY RULES

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ﬂammable liquids,

gases or dust. Power tools create sparks which may ig-

nite the dust or fumes.

3. Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Power tool plugs must match the outlet. Never mod-

ify the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodiﬁed plugs

and matching outlets will reduce risk of electric shock.

2. Avoid body contact with earthed or grounded surfac-

es such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body

is earthed or grounded.

3. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of elec-

tric shock.

4. Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep cord

away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric

shock.

5. When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric

shock.

6. If operating a power tool in a damp location is un-

avoidable, use a ground fault circuit interrupter (GFCI)

protected supply. Use of a GFCI reduces the risk of elec-

tric shock.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use com-

mon sense when operating a power tool. Do not use a

power tool while you are tired or under the inﬂuence

of drugs, alcohol or medication. A moment of inatten-

tion while operating power tools may result in serious

personal injury.

2. Use personal protective equipment. Always wear

eye protection. Protective equipment such as a respira-

tory mask, non-skid safety shoes and hearing protection

used for appropriate conditions will reduce the risk of

personal injury.

3. Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your ﬁnger on the switch or

energizing power tools that have the switch on invites

accidents.

4. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal

injury.

5. Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power

tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jew-

elry. Keep your hair and clothing away from moving

parts. Loose clothes, jewelry or long hair can be caught

in moving parts.

Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”

in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

result in electric shock, ﬁre and/or serious injury.

GENERAL SAFETY RULES

7. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

POWER TOOL USE AND CARE

1. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

2. Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained us-

ers.

5. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s opera-

tion. If damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

power tools.

6. Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking into ac-

count the working conditions and the work to be per-

formed. Use of the power tool for operations different

from those intended could result in a hazardous situa-

tion.

8. Use clamps to secure your workpiece to a stable

surface. Holding a workpiece by hand or using your

body to support it may lead to loss of control.

9. KEEP GUARDS IN PLACE and in working order.

SERVICE

1. Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is main-

tained.

CALIFORNIA PROPOSITION 65 WARNING

Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities may contain

chemicals, including lead, known to the State of Califor-

nia to cause cancer, birth defects, or other reproductive

harm. Wash hands after handling. Some examples of

these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other

masonry products.

• Arsenic and chromium from chemically treated

lumber.

Your risk from these exposures varies depending on

how often you do this type of work. To reduce your ex-

posure to these chemicals, work in a well-ventilated area

with approved safety equipment such as dust masks

specially designed to ﬁlter out microscopic particles.

Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool”

in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

SAVE THESE SAFETY INSTRUCTIONS.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may

result in electric shock, ﬁre and/or serious injury.

Laser Beam Outlet

DO NOT POINT AT EYES

Battery Cover

Reception Lens Mode

Measuring/ON

ON/OFF

B C D E

KNOW YOUR LASER DISTANCE MEASURE

TOOL PURPOSE

Measure distances, lengths, heights, clearances, areas, and volumes with your WEN Laser Distance Measure. Refer

to the following diagrams to become familiarized with all the parts and controls of your tool. The components will

be referred to later in the manual for assembly and operation instructions.

DISPLAY FUNCTIONS

Use the diagram to the left to learn about the vari-

ous icons on your laser distance measure.

A. Laser ON/OFF

B. Length Measurement

C. Area/Volume Measurement

• Area

• Volume

D. Error/Service Needed

E. Battery Level

F. Measurement Reference

• Top

• Base

G. Previous Measurement Value

H. Current Measurement/Area/Volume

I. Unit (m/ft/in/' ")

TURNING ON/OFF

Turning ON: To turn your measuring device ON, you can either press the power button or the measuring but-

ton .

Turning OFF: To turn your measuring device OFF, hold the power button for 1-2 seconds then release it.

Automatic OFF: The device will automatically shut off after 3 minutes of inactivity to prolong battery life.

WARNING: Do not turn on the device until it is fully assembled according to the instructions. Failure to

follow the safety instructions may result in serious personal injury.

NOTE: Always replace both batteries at the same time. Do not use different brands or types of batteries/rechargeable

batteries together.

INSTALLING/REMOVING BATTERIES

Your Laser Distance Measure requires two (2) AAA standard or re-

chargeable batteries (not included).

NOTE: More measurements are possible when using 1.5V rechargeable

batteries rather than 1.2V rechargeable batteries.

1. Push the tab (Fig. 1 - 1) inwards and pull upwards to remove the bat-

tery cover (Fig. 1 - 2).

2. Insert two AAA batteries (not included) into the battery compartment

(Fig. 1 - 3). Follow the diagram inside of the battery compartment to

place the batteries in the correct orientation.

3. Replace the battery cover (Fig. 1 - 2) and press into place.

Fig. 1

WARNING: Remove the batteries from the measuring device when not in use for long periods of time.

The batteries can corrode and self-discharge when left in the device for a long period of time.

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reﬂected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

ASSEMBLY & ADJUSTMENTS

OPERATION

UNIT SELECTION

You can use your device to measure in four different units. The available units are: meters (m), feet (ft), inches

(in), and feet/inches (' ").

NOTE: The feet or inches units will give you measurements in decimals, whereas the feet/inches unit will give you

measurements in a combination of whole feet and whole inches.

To switch between units: While holding the mode button , press the measurement button until your de-

sired unit is displayed on the screen.

CHANGING MODES

After powering your measuring device ON, the default mode is distance measurement . To switch to a different

mode (distance /area /volume ) press the mode button . In the following sections, you can ﬁnd more

information about how to use each mode.

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reﬂected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

SELECTING THE MEASURING REFERENCE POINT

You can set your measuring device to measure from either the base of the unit or from the top of the unit. See

Figures 2 and 3 below to learn more about the two reference point options.

To change the reference point: While holding the mode button , press the power button to switch between

reference points.

Fig. 2 Fig. 3

From the Base From the Top

NOTE:The measurement value appears after a few seconds. The measurement will take longer to appear

depending on the distance, light conditions, and reﬂective properties of the target surface. The end of the mea-

surement is indicated by a tone. The laser beam automatically shuts off after the measurement is completed.

OPERATION

MEASURING A DISTANCE

The distance measuring function is for measuring distances, lengths, heights, and clearances. This function is de-

picted by the arrow symbol .

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reﬂected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

1. Make sure you are in distance measuring mode depicted by the ar-

row symbol . If you’re in a different mode, press the mode button

until you see the arrow symbol on the screen.

2. Make sure to set your measuring device’s reference point and units

(see p. 8).

3. If the laser beam is not ON, press the measurement button to

activate the laser. You will see the laser icon in the top left corner

when the laser is activated. Aim the laser at the point of measurement.

4. Press the measurement button again to take the measurement.

The value will be seen on your display. Your screen will look like Fig. 4.

MEASURING AN AREA

The area measuring function is made for calculating the area of a rect-

angular space. This function is depicted by the area symbol .

1. Make sure you are in area measuring mode depicted by the area

symbol . If you’re in a different mode, press the mode button un-

til you see the area symbol on the screen.

2. Make sure to set your measuring device’s reference point and units

(see p. 8).

3. If the laser beam is not ON, press the measurement button to

activate the laser. You will see the laser icon in the top left corner

when the laser is activated. Aim the laser to measure the length. Press

the measurement button again to take the measurement. The

value will be seen on your display.

4. Repeat step 3 to measure the width. The area will automatically cal-

culate after the second measurement is taken. The value of the width

measurement will be seen on the top row of your screen and the area

will be on the bottom. Your screen will look like Fig. 5.

NOTE: A line will appear on the edge of the area symbol to indicate

which measurement you are recording.

Fig. 4

NOTE: The laser will automatically

shut off after 30 seconds of inactiv-

ity to prolong battery life and limit

accidents.

NOTE: The bottom number on your

display is the current measurement

being recorded. If you take multiple

measurements, the previous mea-

surement moves to the top row.

Laser ON/OFF Distance Mode

Battery

Level

Units

Measurement

Current

Measurement

Fig. 5

Laser ON/OFF Area Mode

Battery

Level

Units

Measurement Area

OPERATION

1. Make sure you are in distance measuring mode depicted by the arrow symbol . If you’re in a different mode,

press the mode button until you see the arrow symbol on the screen.

2. Make sure to set your measuring device’s reference point and units (see p. 8).

3. Hold down the measurement button for two seconds. You are now in continuous measuring mode. As the

distance between the reference point and target point changes, the measurement will update on the screen and

you will hear a tone. Press the measurement button to exit continuous measuring mode.

NOTE: The device will not save the measurements while you are in continuous measuring mode. The laser stays

on the duration of the continuous measurement. DO NOT shine the laser towards people or animals.

MEASURING VOLUME

The volume measuring function is made for measuring the volume of a rectangular prismatic space. This function

is depicted by the cube symbol .

WARNING: Do not direct the laser beam at persons or animals. Do not stare into the direct or reﬂected

laser beam, not even from a distance. Looking into the laser beam or directing the laser beam into someone’s

eyes can cause eye damage, blindness, and cause accidents.

1. Make sure you are in volume measuring mode depicted by the

cube symbol . If you’re in a different mode, press the mode button

until you see the cube symbol on the screen.

2. Make sure to set your measuring device’s reference point and units

(see p. 8).

3. If the laser beam is not ON, press the measurement button to

activate the laser. You will see the laser icon in the top left corner

when the laser is activated. Aim the laser to measure the length. Press

the measurement button again to take the measurement. The

value will be seen on your display.

4. Repeat step 3 two more times to measure the width, and height.

The volume will automatically calculate after the third measurement is

taken. The value of the last measurement will be seen on the top row

of your screen and the volume will be on the bottom. Your screen will

look like Fig. 6.

NOTE: A line will appear on the edge of the volume symbol to

indicate which measurement you are recording.

CONTINUOUS MEASURING

The continuous measuring setting allows you to move the device and

receive updated measurements every few seconds.

Fig. 6

NOTE: The laser will automatically

shut off after 30 seconds of inactiv-

ity to prolong battery life and limit

accidents.

NOTE: The bottom number on your

display is the current measurement

being recorded. If you take multiple

measurements, the previous mea-

surement moves to the top row.

Laser ON/OFF Volume Mode

Battery

Level

Units

Measurement Volume

OPERATION

Indice

Altri manuali Wen Strumento di misura

Wen

Wen 10725 Manuale utente

Wen

Wen 10725 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente