CONTENTS
Introduction ............................................................ 3
This configuration manual .............................................. 3
The Fieldbus Software ................................................. 3
Driver for Siemens PDM software ........................................ 3
Parameter lists abbreviations ........................................... 3
1.0 The Physical Block (PA Slot 0), Profibus ................................... 3
1.1 Diagnosis ........................................................ 3
1.2 Diagnosis of the Device Characteristics ................................ 3
1.3 Physical Block (PA Slot 0) Parameter List, Profibus........................... 4
2.0 The Transducer Block.................................................. 5
2.1 The Transducer Block .............................................. 5
2.2 The data of the Transducer Block Parameter List are grouped as follows:...... 5
2.3 Default configuration ............................................... 5
2.4 Your application set up. ............................................. 5
2.5 AI_Transducer Block Configuration Flowchart............................... 6
2.6 - Transducer Block Examples Setup ...................................... 9
2.6.1 Measurement of RTD with one sensor: ............................... 9
2.6.2 Measurement of RTD with two sensors: .............................. 9
2.6.3 Measurement of thermocouple with one sensor: ........................ 9
2.6.4 Measurement of thermocouple with two sensors: ...................... 10
2.6.5 Measurement of combined sensors (Sensor 1 = TC and Sensor 2 = RTD):. . . . 10
2.6.6 Measurement of resistance (linear) with one sensor: ..................... 10
2.6.7 Measurement of resistance (linear) with two sensors: .................... 11
2.6.8 Measurement of potentiometer (linear) with one sensor: ................. 11
2.6.9 Measurement of potentiometer (linear) with two sensors: ................. 11
2.6.10 Measurement of voltage (linear) with one sensor: ...................... 12
2.6.11 Measurement of voltage (linear) with two sensors: ..................... 12
2.6.12 Measurement of 2 potentiometers (with Linear interpolation linearisation): . . 12
2.6.13 Measurement of TC (with Custom Polynomial Linearisation) on sensor 1 . . . . 13
2.7 AI_Transducer and PR_CUST_LIN Block, Schematic ......................... 14
2.8 AI_TRANSDUCER Block (PA Slot 3) Parameter List .......................... 15
2.8.1 Sensor characterising parameters ................................... 15
2.8.2 RTD / Resistor specific parameters .................................. 16
2.8.3 Thermocouple specific parameters .................................. 16
2.8.4 Output conditioning parameters..................................... 17
2.8.5 Output parameters ............................................... 17
2.8.6 Diagnostic parameters ............................................ 18
2.8.7 Sensor error detection parameters................................... 18
2.8.8 Sensor calibration, Description...................................... 19
2.8.9 Sensor Calibration Parameters...................................... 19
2.9 PR_CUST_LIN Block (PA Slot 4) Parameter List ............................. 21
2.9.1 Linear interpolation linearisation, Description........................... 21
2.9.2 Linear Interpolation Linearisation, Parameter List. ...................... 21
2.9.3 Custom polynomial linearisation, Description .......................... 22
2.9.4 Custom Polynomial Linearisation, Parameter List ....................... 23
2.10 PR_CUST_PRIV Block (PA Slot 5) Reserved Parameter List ................... 23
2.10.1 Description, PR_CUST_PRIV Block ................................. 23
3.0 Analogue Input Blocks, Profibus ......................................... 24
3.1 Analogue Input Blocks Overview, Profibus .............................. 24
3.2 Analogue Input Blocks (PA Slot 1 & 2) Parameter List, Profibus ................. 25
