Yamaha disklavier DKC-850 Manuale di istruzioni
powered by RemoteLive™
Disklavier Control Unit DKC-850
Connection Guide
DisklavierTV service is available for U.S. customers only.
The DKC-850 Disklavier control unit can be connected to several models of Yamaha Disklavier pianos,
however, connections and setup procedures vary depending on the piano model. Check the model number
on the existing control unit and find your piano model following the descriptions below before connecting.
Note:
The model number of the control unit is on the upper part of the display.
■Compatible Models when Equipped with DKC-850
If you are using the piano listed below, replace the existing control unit with DKC-850.
For details on connections and setup, see “Replacing the Existing Control Unit with DKC-850” on page 2.
Important:
Please keep your existing control unit for future maintenance.
Checking the Type of Your Piano
Models Model Number on the Control Unit
Upright pianos Disklavier Mark II XG Series DKC500R, DKC500RXG, DKC500RW,
DKC500RWXG
Disklavier Mark II XG Series (MX116, MX22, MX500) DKC50R
Disklavier Mark III Series (DU1A) DKC55RCD
Grand pianos Disklavier Mark II XG Series DKC500R, DKC500RXG, DKC500RW,
DKC500RWXG
Disklavier Mark III Series Full-Function Models DKC55RCD
Disklavier Mark III Series Standard Models DKC60RCD
Disklavier Mark III Series PRO Models DKC55RCD
Disklavier Mark III Series Playback Models DKC55, DKC55CD
2
Connect DKC-850 to your piano, replacing with the existing control unit.
Replacing the Existing Control Unit with DKC-850
Cautions
• Use the Yamaha PJP-PS02/PJP-PS04 adaptor, or an equivalent recommended by Yamaha. Use of
other AC adaptors may result in damage, overheating, or fire.
• Do not stretch the cable or bend its ends.
• Do not attempt to use the cable if it is stretched or if the ends of the cable have been bent. Attempting
to do so may cause interruptions to the power supply.
• Always turn off the main unit power before disconnecting the AC adaptor.
• When you wish to move DKC-850, unplug the AC adaptor from the AC wall outlet and disconnect if
from the DC-IN 12V connector on the rear panel of DKC-850 before proceeding.
• Unplug the AC adaptor from the AC wall outlet if you do not intend to use the instrument for an
extended period of time.
Connect monitor
speakers.
See page 4.
578
4 3 9
6
Tighten
AC adaptor (PJP-PS02/PJP-PS04)
(supplied)
Power cable
(supplied)
Conversion
cable
(supplied)
Control
cable
Your piano
Tighten Loosen
DKC-850
3
Turn on your piano, and reset settings on your control unit
to its factory default.
For details on setting, refer to your piano’s owner’s manual.
Turn off your piano, and disconnect the power cable from
the AC wall outlet.
Note:
The location of the TO CONTROL
CABLE FOR PIANO connector
varies depending on the piano model.
Disconnect the control cable from the TO CONTROL
CABLE FOR PIANO connector on the rear panel of your
control unit.
Loosen the two screws attached to the connector using a
screwdriver.
Attention:
DKC-850 does not work properly if
the control cable is connected
directly to it. Use the supplied
conversion cable to connect your
piano and DKC-850.
Connect the supplied conversion cable to the control cable
disconnected in step 2.
Tighten the two screws attached to the connector using a
screwdriver.
Connect the supplied conversion cable to the TO PIANO
connector on the rear panel of DKC-850.
Tighten the two screws attached to the connector using a
screwdriver.
See “Connecting Monitor Speakers”
on page 4.
Connect monitor speakers to the OUTPUT jacks on the rear
panel of DKC-850.
Connect the supplied AC adaptor to the DC-IN 12V
connector on the rear panel of DKC-850.
Connect the supplied power cable to the AC adaptor.
Connect the power cable extended from your piano and the
AC adaptor to the AC wall outlet.
See “Setting the Type of Your Piano”
on page 5.
The connection completed.
Turn on DKC-850, and set the piano type.
Important
• Be sure to backup the data on your existing control unit to a floppy disk before connecting.
• Please keep your original control unit for future maintenance.
1
2
3
4
5
6
7
8
9
4
To listen to the internal XG tone generator voices, you have to connect
monitor speakers. Connection methods vary depending on whether your
piano is equipped with the Silent Piano™ function or not.
■For Pianos Equipped with the Silent Piano™
Function
Note:
The shape of units or the location of
the AUX IN jacks varies depending
on the piano model.
Connect the AUX IN jacks of your piano to the OUTPUT jacks on the rear of
DKC-850 with the supplied audio cable.
■For Pianos Not Equipped with the Silent Piano™
Function
Note:
Two audio cables (pin plug – phone
plug) are supplied to connect this unit
to the piano equipped with the Silent
Piano™ function. Prepare suitable
cables for connection of the monitor
speakers.
Connect the input jacks of monitor speakers to the OUTPUT jacks (pin
jacks) on the rear of DKC-850 with audio cables.
(Example: connecting the Yamaha MSP3 monitor speakers)
Connecting Monitor Speakers
For models with the control box
Connect with the supplied audio
cable (pin plugs – stereo mini plug).
For models with the amplifier
Connect with the supplied audio
cables (pin plug – phone plug).
DKC-850
To AUX IN jack
(stereo mini plug)
Audio cable
(supplied)
DKC-850
To AUX IN jacks
(phone plug)
Audio cables
(supplied)
Audio cable
(pin plug – pin plug)
(not supplied) Audio cable
(pin plug – pin plug)
(not supplied)
AC wall outlet
DKC-850
POWER
ON
OFF
INPUT
PARALLEL
LINE 1
(--10dB)
LINE 2
(--4dB)
POWER
ON
OFF
INPUT
PARALLEL
LINE 1
(--10dB)
LINE 2
(--4dB)
POWER
ON
OFF
Monitor
speaker (right)
Monitor
speaker (left)
5
After you have connected DKC-850 to your piano, you must set the type of
your piano.
Press [SYSTEM] on the remote control.
The system menu screen appears.
Select “PianoType” with the cursor buttons ([ ] [ ] [ ]
[ ]), then press [ENTER].
The piano type setup screen appears.
Note:
If you select “Replace” and this unit
detects your piano as the playback
model, “[PB]” appears on the right of
the screen.
Confirm that the piano type is set to “Replace.”
If not, press [+/YES] or [–/NO] to change its setting to
“Replace.”
Press [ENTER].
If the piano type has been changed, this unit is automatically
rebooted.
Setting the Type of Your Piano
[SYSTEM] “PianoType”
1
!"#$%
{
2
*Language
=SYSTEM MENU= (2/2)
_
*PianoType
*Display
>Type=Replace
>Piano=REC
=PianoType= -+ENT
3
>Type=Replace
>Piano=REC
=PianoType= -+ENT
4
Restarting...
=PianoType=
Copyright © 2013 Yamaha Corporation Sep-13
P.O.Box 1, Hamamatsu, 430-8650 Japan
Altri manuali per disklavier DKC-850
6
Indice
Altri manuali Yamaha Unità di controllo
Yamaha
Yamaha DTX-PRO Manuale utente
Yamaha
Yamaha ACU16-C Manuale utente
Yamaha
Yamaha ACD1 Manuale utente
Yamaha
Yamaha REV-1 Manuale utente
Yamaha
Yamaha Disklavier DKC55RCD XG Mark III Manuale utente
Yamaha
Yamaha disklavier DKC-850 Manuale utente
Yamaha
Yamaha V9938 Manuale
Yamaha
Yamaha disklavier DKC-850 Manuale di istruzioni
Yamaha
Yamaha MusicCAST MCX-CA15 Manuale
Yamaha
Yamaha ACD1 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
