ZCS CONNEXT Manuale utente

ACCESSORY

CONNEXT

Identification: MD-AL-GI-00

Rev. 4.0 of 07/06/2021 - Application: GID

Zucchetti Centro Sistemi S.p.A. - Green Innovation Division

Via Lungarno, 248 - 52028 Terranuova Bracciolini - Arezzo, Italy

tel. +39 055 91971 - fax. +39 055 9197515

innovation@zcscompany.com - [email protected] - zcsazzurro.com

Reg. Pile IT12110P00002965 - Share Capital € 100,000.00 fully paid up

AR Company Reg. no. 03225010481 - REA AR no. 94189

ISO 9001 Certified Company - Certificate no. 9151 - CNS0 - IT-17778

Connext User Manual

Rev. 1.2 07/06/2021

“CONNEXT” Control System

User Manual

Main Document Only.

2/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

General instructions

This manual contains important safety instructions that must be followed during installation and

maintenance of the equipment.

Please keep these instructions!

This manual must be considered an integral part of the equipment, and must be available at all

times to everyone who interacts with the equipment. The manual must always accompany the

equipment, even when it is transferred to another user or plant.

The copyright of this manual belongs to Zucchetti Centro Sistemi S.p.A. No part of this manual

(including the software, etc.) may be copied, reproduced or distributed in any form or by any

the right to final interpretation. This manual is subject to change based on feedback from users,

installers or customers. Please check our website http://www.zcsazzurro.com for the latest

version.

Technical support

ZCS offers a support and technical consultancy service accessible by sending a request directly

from the website https://www.zcsazzurro.com/it/support.

The following toll-free number is available for the Italian territory: 800 72 74 64.

Main Document Only.

3/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

Table of Contents

1. Preliminary safety instructions..........................................................................................................7

1.1. Safety instructions .....................................................................................................................7

1.2. Symbols and icons......................................................................................................................9

1.3. Labels.......................................................................................................................................10

2. Product features .............................................................................................................................11

2.1. Product presentation ...............................................................................................................11

2.2. Product overview.....................................................................................................................12

2.2.1. 24-pin terminal block ....................................................................................................................14

2.2.2. 3-pin terminal block ......................................................................................................................15

2.2.3. SD card slot ...................................................................................................................................15

2.2.4. Ethernet connector .......................................................................................................................15

3. Installation......................................................................................................................................16

3.1. Checks before installation ........................................................................................................16

3.1.1. Installation tools ...........................................................................................................................17

3.2. Installation process ..................................................................................................................17

3.2.1. Installation position.......................................................................................................................17

3.3. Materials and cables ................................................................................................................18

4. Electrical connections .....................................................................................................................19

4.1. Connecting the AC power cables..............................................................................................19

4.2. Connecting to Azzurro EV charging stations .............................................................................20

4.3. Connecting to Azzurro photovoltaic or storage inverters .........................................................22

4.3.1. Connecting to 1-phase Azzurro hybrid inverters ............................................................................22

4.3.2. Connecting to 3000SP inverter ......................................................................................................23

4.3.3. Connecting to Azzurro 3-phase hybrid inverters ............................................................................24

4.3.4. Connecting to Azzurro single-phase photovoltaic inverters ...........................................................25

4.3.5. Connecting to Azzurro three-phase photovoltaic inverters ............................................................26

4.4. Connecting to current sensors or meter...................................................................................27

Main Document Only.

4/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

4.4.1. Sensor for measuring 1-ph photovoltaic production......................................................................27

4.4.2. Sensor for measuring three-phase photovoltaic production ..........................................................28

4.4.3. Sensor for measuring 1-phase grid exchanges ...............................................................................29

4.4.4. Meter for measuring grid exchanges (three-phase system) ...........................................................30

5. Initial system configuration.............................................................................................................31

6. Access for maintenance only...........................................................................................................46

6.1. Access connection for maintenance only .................................................................................46

7. Technical datasheet ........................................................................................................................47

8. Maintenance...................................................................................................................................48

8.1. Troubleshooting.......................................................................................................................48

8.2. Maintenance............................................................................................................................48

9. Dismantling and disposal ................................................................................................................49

10. Warranty terms and conditions ...................................................................................................50

Main Document Only.

5/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

Preface

General information

Please read this manual carefully before installation, use or maintenance. This manual contains

important safety instructions that must be followed during installation and maintenance of the

system.

Scope

This manual describes the assembly, installation, electrical connections, commissioning,

maintenance and troubleshooting of the Connext system. Keep this manual so that it is accessible at

all times.

Recipients

This manual is intended for qualified technical personnel (installers, technicians, electricians,

technical support personnel or anyone who is qualified and certified to work on an electrical

system), responsible for installation and start-up of the system. The manual is also intended for end

users who can find useful information on how to manage their installation via the Connext system.

Symbols used

This manual provides information for safe operation and uses certain symbols to ensure the safety

of personnel and materials, and for efficient use of the equipment during normal operation.

It is important to understand this information to prevent accidents and damage to property. Please

take note of the following symbols used in this manual.

Danger: indicates a hazardous situation which, if not resolved or

avoided, could result in serious personal injury or death

Danger

Warning: indicates a hazardous situation which, if not resolved or

avoided, could result in serious personal injury or death

Warning

Main Document Only.

6/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

Caution: indicates a hazardous situation which, if not resolved or

avoided, could result in minor or moderate personal injury

Caution

Attention: indicates a potentially hazardous situation which, if not

resolved or avoided, could result in damage to the system or other

property

Attention

Note: provides important tips on correct and optimal operation of

the product

Note

Main Document Only.

7/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

1. Preliminary safety instructions

If you have problems or questions in reading and understanding the

following information, please contact Zucchetti Centro Sistemi S.p.A.

through the appropriate channels.

Note

1.1. Safety instructions

This section highlights the main safety instructions to be followed during installation and use of the

equipment.

Before installing and using the equipment, make sure you read and understand the instructions in

this manual and familiarise yourself with the relative safety symbols shown in this chapter.

According to national and local requirements, permission must be obtained from your local

provider before connecting to the electrical grid, making sure that the connections are carried out

by a qualified electrician. All installation operations must be carried out by a qualified and

competent electrician.

Contact the nearest authorised service centre for any repairs or maintenance. Contact your

distributor for information on the nearest authorised service centre. DO NOT carry out repairs

yourself, as this may result in injury or damage.

Qualified personnel

Ensure that the operator has the necessary skills and training to operate the equipment. Personnel

responsible for use and maintenance of the equipment must be qualified and capable of performing

the activities described, and must also have adequate knowledge on how to correctly interpret the

contents of this manual. For safety reasons, this system must only be installed by a qualified

electrician with the necessary training and/or skills and knowledge. Zucchetti Centro Sistemi S.p.A.

declines all responsibility for damage to property or personal injury caused by incorrect use of the

device.

Do not attempt in any way to repair or replace components of the system without the assistance of

qualified personnel.

Installation requirements

Install and start the system according to the following instructions. Choose a suitable location for

installation of the electrical equipment. Make sure there is sufficient space to accommodate future

maintenance work.

Main Document Only.

8/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

Figure 1 –Do not lose or damage this manual

Transport requirements

If there are any problems with the packaging that could cause damage to the system or if there is

visible damage, notify the transport company immediately. If necessary, request assistance from an

installer or from Zucchetti Centro Sistemi S.p.A. Transport of the equipment, especially by road,

must be carried out with vehicles suitable to protect the components (especially the electronic

components) against violent knocks, humidity, vibrations, etc.

Electrical connections

Please follow all the current electrical regulations concerning accident prevention.

Before connecting the power supply, make sure to properly

disconnect the voltage on the AC connection cables.

Danger

All installation operations must be carried out by a professional

electrician, who is prepared and has read this manual carefully and

understands its contents!

Warning

Do not remove the information label or to tamper with the system.

Otherwise, ZCS will not provide any warranty or assistance.

Note

Main Document Only.

9/50

Identification: MD-AL-GI-00

Rev. 1.0 07.06.21 - Application: GID

Connext User Manual

Rev. 1.2 07/06/2021

Operation

Do not use the product if it has any defects, cracks, scratches or leaks, but contact your dealer or

ZCS technical service.

Contact with the electrical grid or the terminal of the equipment

may cause electrocution or fire!

•

Do not touch the terminal or the conductor connected to the

electrical grid.

•

Follow all the instructions and safety requirements relating to grid

connection

Danger

If the system is not functioning properly:

•

Disconnect the input and output power supply

Warning

Maintenance and repair

Keep the system clean and dry; if you need to clean it, use a clean dry cloth.

1.2. Symbols and icons

Introduces the main safety symbols on the charging station. Some safety symbols are located on the

charging station. Before installation, it is important to read and understand the contents of the

symbols.

Complies with the European Standards (CE)

Ground connection point

Table 1 –Symbols on the System

’Smin"“’"

There is residual voltage in the inverter! Before opening the equipment,

wait five minutes to ensure that the capacitance has been completely

discharged.

Be careful of high voltage.

Be careful of high temperature.

Complies with European standards.

Ground connection point.

This indicates the allowed temperature range.

Indice

Altri manuali ZCS Sistema di controllo

ZCS

ZCS AZZURRO CONNEXT Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente