Zebex ZB- 800 SERIES Manuale utente

ZBX98070101

P/N : MUL-53215-01

USER'S MANUAL

ZB- 800

SERIES

The manual can be used as

keyboard emulation, RS- 232C

serial interface, and CMOS serial

interface.

IMPORTANT NOTICE

ZEBEX INDUSTRIES INC. MAKES NO

WARRANTY WITH REGARD TO THIS MATERIAL,

INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.

ZEBEX INDUSTRIES INC. SHALL NOT BE

LIABLE FOR ERRORS CONTAINED HEREIN OR

FOR INCIDENTAL CONSEQUENTIAL DAMAGES

IN CONNECTION WITH THE FURNISHING,

PERFORMANCE, OR USE OF THIS MATERIALS.

ZEBEX INDUSTRIES INC.

IBM is a registered trade mark of International Business Machines

Corp.

IBM PC/XT is a product of International Business Machines Corp.

IBM PC/AT is a product of International Business Machines Corp.

IBM PS/2 is a product of International Business Machines Corp.

NEC is a registered trade mark of NEC Corporation.

All other registered trade marks are registered companys'

property.

ZEBEX is a registered trade mark of ZEBEX INDUSTRIES INC.

portion of its contents is not allowed without the specific

written consent of ZEBEX INDUSTRIES INC.

Every effort is made to ensure the accuracy of our

product information; however, we accept no responsibility

for errors or omission. Specification or version may be

subject to change without notice. The actual

specification and version are based on the product

delivered.

PRINTED IN DECEMBER 1995

USER'S MANUAL

The manual can be used as

keyboard emulation, RS- 232C

serial interface, and CMOS serial

interface.

IMPORTANT NOTICE

Every effort is made to ensure the

accuracy of our product information;

however, we accept no

responsibility for errors or omission.

Specification or version may be

subject to change without notice.

The actual specification and version

are based on the product delivered.

PRINTED IN DECEMBER 1995

TABLE OF CONTENTS

Introduction....................................................1

Default Parameters.........................................2

Program Procedure ........................................5

System Setting...............................................6

Header And Trailer.........................................7

Inter- Message Delay......................................7

Inter- Character Delay ....................................7

Message/ Block Mode Selection .....................8

Beeper Tone Selection ...................................8

Bar Code ID Selection....................................9

RS- 232C Serial Communication Parameters

Setting .......................................................10

Handshaking Protocol...........................10

ACK/ NAK Response Time Setting........10

Baud Rate............................................11

Data Bit................................................11

Stop Bit................................................12

Parity Setting........................................12

Message Terminator.............................12

Keyboard Emulation Parameters Setting.......13

Keyboard Type Selection......................13

Language Selection..............................14

Message Terminator.............................15

Reading Code Selection...............................15

Code 39 Parametrs Setting...........................17

Interleaved 2 Of 5 Parameters Setting...........18

SLZ 2 Of 5 Parameters Setting .....................18

UPC/ EAN/ JAN Parameters Setting .............19

Codabar/ Monarch Parameters Setting..........22

Code 128 Parameters Setting.......................23

ISBN/ ISSN Conversion................................23

Appendix A

Code 39 Full ASCII Code Table ....................24

Appendix B

Code 39 Full ASCII Bar Code TAble..............26

1. INTRODUCTION

The series Bar Code Wand scanners can be

configured by scanning a series of programming

bar code labels. This allows decoding options and

interface protocols to be tailored to a specific

application. The configuration is stored in non-

volatile memory and will not be lost by removing

power from the scanner.

The scanner must be properly powered before

programming. For RS-232C type scanners, an

external power adaptor must be used to supply DC

power to the scanner. If a keyboard emulation

type scanner is used with a IBM PC/XT/AT, PS/2 or

any fully compatible computers, power will be

drawn from the keyboard port. No external power

adaptor is required. If keyboard emulation type

scanner is used with any other non IBM PC

compatible computers, an external power adaptor

may be needed.

During the programming mode, the scanner will

acknowledge a good and valid reading with a short

beep. It will give long beeps for either an invalid

or bad reading.

2. PROGRAMMING OPTIONS

Programmable options are divided into four groups.

The first group includes the options that show the

general behavior of the scanner. The second

group of options governs the operation of RS-232C

type serial ports. The third group selects the

keyboard type that the keyboard emulation type will

be emulated. The last group sets the decoding

parameters for each bar code symbology.

3. DEFAULT PARAMETERS

This table gives the default settings of all the

programmable parameters. The default settings

will be restored whenever the "Reset" programming

label is scanned and the scanner is in

programming mode.

DEFAULT VALUES OF OPERATING PARAMETERS

Function Default Values

Header and trailer None

Inter-Message delay Normal

Inter-Character delay Normal

Message/Block mode selection Message

Send command in block mode

communication Disable

Good read beeper tone selection 2KHz/120

mSec

Code identifier transmmiting Disable

Code 39 bar code identifier code M

ITF 2 of 5 bar code identifier code I

SLZ 2 of 5 bar code identifier code H

UPC-E bar code identifier code E

UPC-A bar code identifier code E

EAN-13 bar code identifier code F

EAN-8 bar code identifier code FF

Codabar bar code identifier code N

Code 128 bar code identifier code K

Code 93 bar code identifier code L

MSI bar code identifier code P

DEFAULT VALUES OF KEYBOARD EMULATION

PARAMETERS SETTING

Function Default Values

Keyboard type selection IBM PC/AT USA

Message terminator Enter/ Carriage

Return

DEFAULT VALUES OF RS-232C SERIAL

COMMUNICATION PARAMETERS

Function Default Values

Handshaking protocol None

ACK/NAK response

time setting 300 msec

Baud rate 9600

Data bit 8

Stop bit 1

Parity Mark (None)

Message terminator

selection CR/LF

DEFAULT VALUES OF DECODING

PARAMETERS

Function Default Value

Code 39 Enable

ITF 2 of 5 Enable

SLZ 2 of 5 Disable

UPC/EAN/JAN Enable

Codabar Enable

Reading Codes¡°MSI Disable

Selection Code 128 Enable

Code 93 Enable

¡°ITAT Disable

¡° Italian Pharmac Disable

ISSN/ ISBN Disable

Codes Standard

Code 39 Start/stop characters Not transmitting

Check digit Disable

Interleaved Length 10 digits Fixed

2 of 5 Check Digit Disable

SLZ 2 of 5 Length Variable

Check Digit Disable

Format All

Addendum Disable

UPC-E=UPC-A Disable

UPC-A= EAN-13 Disable

UPC/EAN/JAN UPC-A Leading Digit Transmit

UPC-A Check Digit Transmit

UPC-E Leading Digit Transmit

UPC-E Check Digit Transmit

EAN-13 Check Digit Transmit

EAN-8 Check Digit Transmit

Type Standard

Codabar Start/ Stop

Characters A,B,C,D

Code 128 FNC 2 Append Disable

Check Digit Calculate but not

Transmit

MSI Length Variable

Check digit Transmit

Italian Pharmac Transmit "A"

Character Not transmitting

Note: The configuration of the items with

asterisk (¡°)is optional.

4. PROGRAM PROCEDURE USING BAR CODE

MENUS

START

Read Start of

Configuration Label

Set All

Defaults Set

Operating

Parameters

Set

Serial Port

Parameters

Set

Keyboard

Type

Set

Decoding

Parameters

No No

Finish Discard

Yes Yes

Read End of

configuration

label

Read Abort

Label

END

Start of Configuration

•The reading of the "RESET " label turns all the

parameters back to default values.

•When you intend to turn your scanner back to

default parameter, please scan the "Start of

configuration" label first, then scan "RESET"

label and finally scan the "End of configuration"

label.

RESET

•The reading of the "ABORT" label discards all

the parameters read prior to the "End of

configuration".

ABORT

•The lable below must be read to enter into

serial interface for ZB- 800R or ZB- 800C when

the wand is configured the first time.

RS-232C

•The lable below must be read to enter into

serial interface for ZB- 800K when the wand is

configured the first time.

PC/ AT

HEADER AND TRAILER

Header

Set

Trailer

INTER-MESSAGE DELAY

None

500 mSec

100 mSec

1 Second

INTER-CHARACTER DELAY

None

20 mSec

10 mSec

50 mSec

End of Configuration

Start of Configuration

MESSAGE/BLOCK MODE SELECTION

Message

Block

SEND COMMAND IN BLOCK MODE

COMMUNICATION

Enable

Disable

Store

Set

GOOD READ BEEPER TONE SELECTION

2KHz/ 120 mSec

2 KHz/ 200 mSec

1 KHz/ 120 mSec

1 KHz/ 200 mSec

Disable

BAR CODE IDENTIFIER CODE SELECTION

Enable

Disable

BAR CODE IDENTIFIER CODE SETTING

UPC- E

EAN- 13

SLZ 2 OF 5

Codabar

UPC- A

EAN- 8

ITF 2 OF 5

Code 39

End of Configuration

Start of Configuration

BAR CODE IDENTIFIER CODE SETTING (Cont' d)

Code 128

MSI

Code 93

Set

RS-232C SERIAL COMMUNICATION

PARAMETERS SETTING

HANDSHAKING PROTOCOL

None

RTS/ CTS

ACK/ NAK

Xon/ Xoff

ACK/NAK RESPONSE TIME SETTING

300 mSec

2 Sec

500 mSec

1 Sec

3 Sec

5 Sec

BAUD RATE

19200

9600

4800

1200

2400

600

DATA BIT

End of Configuration

Indice

Altri manuali Zebex Lettore di codici a barre

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente