Advantech USB-5801 Manuale di installazione e funzionamento
USB-5801 Startup Manual 1
Before installation, please ensure that the following items
are included with the product:
• 1 x USB-5801 module
• 4 x Terminal blocks
• 1 x USB 3.0 lockable cable (1 m)
• 1 x USB-5801 startup manual
If any of the above items are missing or damaged, contact
your distributor or sales representative immediately
User Manual
For more detailed information regarding this product, please
download the USB-5801 user manual from the Advantech
website.
USB-5801 is a highly accurate dynamic signal acquisition
USB 3.0 module specifically designed for vibration and
acoustic measurements. The module provides four simulta-
neously sampled 24-bit IEPE sensor inputs with an up to 192
kS/s sample rate for high-resolution measurements. USB-
5801 is also equipped with two 24-bit analog outputs with an
up to 192 kS/s update rate and two tachometer inputs whose
data can be correlated to the sensor data. The built-in USB
hub makes this module daisy chainable with other USB-5000
series products.
USB-5801
4-Ch, 24-Bit, 192 kS/s
Dynamic Signal Acquisition
USB
3.0 I/O Module with Analog Output and Tachometer
Startup Manual
FCC Class A
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause interference. In such cases, users are
required to correct the interference at their own expense.
CE
This product has passed the CE test for environmental speci-
fications when shielded cables are used for external wiring.
We recommend the use of shielded cables.This kind of cable
is available from Advantech. Please contact your local sup-
plier for ordering information.
Analog Input
• Channels: 4 (simultaneous sampling, 50 Ωpseudo
differential configurable)
• Resolution: 24 bits (delta-sigma ADC)
• Max. Sampling Rate: 1 ~ 192 kS/s
• Input Coupling: AC/DC, selectable per channel
• Trigger Mode: Start, delay start, stop, delay stop
• Input Range: ±1 V, ±2 V, ±5 V, ±10 V
• Offset Error: < ±0.2 mV
• Gain Error:< ±0.02% of full-scale range
• Total Harmonic Distortion Plus Noise (THD+N): -95 dB
• IEPE Excitation: 2 mA
• Automatic Calibration: Ye s
Analog Output
• Channels: 2 (50 Ωpseudo differential)
• Resolution: 24 bits (delta-sigma DAC)
• Update Rate: 1 ~ 192 kS/s
• Output Coupling: DC
• Output Range: ±1 V, ±10 V
• Offset Error: < ±0.5 mV
• Gain Error: < ±0.03% of full-scale range
Declaration of ConformityPacking List
For more information about this or other Advantech
products, visit our website at
http://www.advantech.com
For technical support and customer service, visit our
support website at
http://support.advantech.com
This manual is for USB-5801.
Part No. 2041580101
Printed in China
Edition 2
May 2019
Specications
Overview
2 USB-5801 Startup Manual
• Total Harmonic Distortion Plus Noise (THD+N): -91 dB
• Trigger Mode: Start, delay start, stop, delay stop
• Automatic Calibration: Ye s
Tachometer Input
• Channels: 2
• Input Voltage: Logic 0: 3 V max.
Logic 1: 10 V min. (30 V max.)
• Input Frequency: 5 kHz max.
• Digital Filter: 16 μs ~ 131 ms
• Isolation Protection: 2,500 VDC
Digital Input
• Channels: 4
• Input Voltage: Logic 0: 3 V max.
Logic 1: 10 V min. (30 V max.)
• Opto-Isolator Response Time: 100 μs
• Digital Filter: 16 μs ~ 131 ms
• Isolation Protection: 2,500 VDC
Digital Output
• Channels: 4
• Load Voltage: 5 ~ 40 VDC
• Load Current: 350 mA/ch (sink)
• Opto-Isolator Response Time: 100 μs
• Isolation Protection: 2,500 VDC
General
• Interface: USB 3.0
• Data Transfer Rate: 5 Gbps
• Connectors:
6 x BNC (AI and AO)
2 x 10-pin, 3.81-mm terminal blocks (tachometer, trigger,
and DI/O)
2 x 3-pin, 3.81-mm terminal blocks (power)
1 x USB 3.0 type A (downstream port)
1 x USB 3.0 type B (upstream port)
• Dimensions:
168 x 120 x 40 mm (6.6 x 4.7 x 1.6 in)
• Operating Temperature: 0 ~ 60 °C (32 ~ 140 °F)
• Storage Temperature: -40 ~ 70 °C (-40 ~ 158 °F)
• Storage Humidity: 5 ~ 95% RH (non-condensing)
• Power Supply: External 10 ~ 30 VDC or USB bus power
• Power Consumption:
150 mA typ./200 mA max. @24 V external power
700 mA typ./860 mA max. @5 V bus power
Specications (Cont.)
We recommend installing the driver before installing the
USB-5801 module to guarantee problem-free installation.
The Advantech DAQNavi Device Drivers setup program
for the USB-5801 module can be downloaded from the
Advantech website (www.advantech.com). Follow the steps
outlined below to install the driver software.
1. Execute the USB-5801 driver package.
2. The driver installation program should be launched.
When the setup program is launched, a setup screen
will be displayed.
3. Click the “Next” button and wait for driver installation.
4. Click the “Finish” button to exit the setup program.
After the device drivers are installed, the USB-5801 module
can be installed in the computer. We recommend referring
to the user manual or related documentation for detailed in-
structions. Alternatively, follow the steps outlined below for
module installation.
1. Touch any metal surface of the computer to discharge
any static electricity that may be in your body.
2. Insert the USB module into the designated USB port.
Use caution when inserting the module to avoid damage
due to excessive force.
After the module is installed, the device can be configured
using the Advantech Navigator Program automatically in-
stalled during driver setup. Complete device installation pro-
cedures should include device setup, configuration, and test-
ing. Information is provided in the following sections to guide
users through the device setup, configuration, and testing.
Hardware Installation
Driver Installation
USB-5801 Startup Manual 3
Block Diagram
Connector, Switch, and LED Locations
4 USB-5801 Startup Manual
Switch Description
SW1
Board ID switch. Refer to the table below for board ID configuration.
Board ID 1 2 3 4
0
↑ ↑ ↑ ↑
1
↑ ↑ ↑ ↓
2
↑ ↑ ↓ ↑
3
↑ ↑ ↓ ↓
4
↑ ↓ ↑ ↑
5
↑ ↓ ↑ ↓
6
↑ ↓ ↓ ↑
7
↑ ↓ ↓ ↓
8
↓ ↑ ↑ ↑
9
↓ ↑ ↑ ↓
10
↓ ↑ ↓ ↑
11
↓ ↑ ↓ ↓
12
↓ ↓ ↑ ↑
13
↓ ↓ ↑ ↓
14
↓ ↓ ↓ ↑
15
↓ ↓ ↓ ↓
Connector Description
CN1 USB upstream port (USB 3.0 type-B connector with screw). Connect this port to the host or the down-
stream port of the previous USB module.
CN2 USB downstream port (USB 3.0 type-A connector with screw). Connect this port to the upstream port of
the next USB module, if any.
Board ID Switch and Connectors
USB-5801 Startup Manual 5
Connector Pin Description
CN4
Center pin Positive terminal of analog input channel 0
Outer shield Negative terminal of analog input channel 0
CN5
Center pin Positive terminal of analog input channel 1
Outer shield Negative terminal of analog input channel 1
CN6
Center pin Positive terminal of analog input channel 2
Outer shield Negative terminal of analog input channel 2
CN7
Center pin Positive terminal of analog input channel 3
Outer shield Negative terminal of analog input channel 3
CN8
Center pin Positive terminal of analog output channel 0
Outer shield Negative terminal of analog output channel 0
CN9
Center pin Positive terminal of analog output channel 1
Outer shield Negative terminal of analog output channel 1
Connector Pin Description
CN10 & CN11
C<0…1>CLK Clock input for counter channel 0 and 1
C<0…1>SCK Sample clock input for counter channel 0 and 1
TRGIN Digital trigger input
TRGOUT Digital trigger output
I<0…3> Digital input channel 0 through 3
O<0…3> Digital output channel 0 through 3
EC Common point for digital input signals
PC Common point for digital output signals
GND Ground for digital signals
Connector Pin Name Description
CN12 &
CN13
+VS External 10 ~ 30 V
DC
power supply
GND Power ground
Chassis ground
Note: CN12 and CN13 are used for power redundancy. External power can be supplied by either connector.
Pin Assignments
6 USB-5801 Startup Manual
LED State Description
LED2
Off Module is not powered on
Green Module is powered on using either USB bus power or external power
LED3
Off Initial state. Module has not been connected
Green Upstream port is connected. Module is functioning normally
Red Upstream port is not connected or is disconnected. Module function is halted
LED4
Off Downstream port is not connected
Blue Downstream port is connected
LED State Description
Near CN4
Off No sensor is connected to analog input channel 0 or the sensor wire is broken
Green Sensor is connected to analog input channel 0 and works normally
Red Sensor connected to analog input channel 0 is short circuited
Near CN5
Off No sensor is connected to analog input channel 1 or the sensor wire is broken
Green Sensor is connected to analog input channel 1 and works normally
Red Sensor connected to analog input channel 1 is short circuited
Near CN6
Off No sensor is connected to analog input channel 2 or the sensor wire is broken
Green Sensor is connected to analog input channel 2 and works normally
Red Sensor connected to analog input channel 2 is short circuited
Near CN7
Off No sensor is connected to analog input channel 3 or the sensor wire is broken
Green Sensor is connected to analog input channel 3 and works normally
Red Sensor connected to analog input channel 3 is short circuited
Note: LEDs near CN4 ~ CN7 function only when IEPE is enabled for the corresponding analog input channel.
LED Status Descriptions
Altri manuali per USB-5801
1
Indice
Altri manuali Advantech Unità di controllo
Advantech
Advantech ADAM-3656 Manuale di installazione e funzionamento
Advantech
Advantech IPMI-2000 Manuale di installazione e funzionamento
Advantech
Advantech ADAM-6217 Manuale utente
Advantech
Advantech MIC-75G20-10B1 Manuale di installazione e funzionamento
Advantech
Advantech iDAQ-817 Manuale utente
Advantech
Advantech SOM-5897 Manuale utente
Advantech
Advantech PCM-3664 Manuale di installazione e funzionamento
Advantech
Advantech PCM-3643 Manuale di installazione e funzionamento
Advantech
Advantech ADAM-5000 Series Manuale utente
Advantech
Advantech PCM-24BXWF Manuale di installazione e funzionamento
Advantech
Advantech PCM-3910 Manuale di installazione e funzionamento
Advantech
Advantech AMAX-3285IO Manuale di installazione e funzionamento
Advantech
Advantech IPMI-1000 Manuale di installazione e funzionamento
Advantech
Advantech MIO-6255 Manuale di installazione e funzionamento
Advantech
Advantech PCM-23C1CF Manuale utente
Advantech
Advantech B+B SmartWorx 232PTC9 Manuale utente
Advantech
Advantech EPD-132 Manuale utente
Advantech
Advantech PCM-3116 Manuale di installazione e funzionamento
Advantech
Advantech EPD-130 Manuale utente
Advantech
Advantech WISE-1540 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
