AEMC OX 5042 Manuale utente

Oscilloscope

Model OX 5042

ENGLISH

Quick Start Guide

www.aemc.com

Chauvin Arnoux®, Inc.

d.b.a AEMC®Instruments

www.aemc.com

Statement of Compliance

Chauvin Arnoux®, Inc. d.b.a. AEMC®Instruments

certiﬁes that this instrument has been calibrated

using standards and instruments traceable to

international standards.

We guarantee that at the time of shipping your

instrument has met its published speciﬁcations.

An NIST traceable certiﬁcate may be

requested at the time of purchase, or obtained

by returning the instrument to our repair and

calibration facility, for a nominal charge.

The recommended calibration interval for this

instrument is 12 months and begins on the date of

receipt by the customer. For recalibration, please

use our calibration services. Refer to our repair

and calibration section at www.aemc.com.

Serial #: ________________________________

Catalog #:

Model #: OX5042

Please ﬁll in the appropriate date as indicated:

Date Received: _________________________________

Date Calibration Due: _______________________

(1) U.S. Wall Plug 18W,

100-240V, 50/60Hz

Cat. #5000.51

USB DRIVE CONTENTS: The SX-METRO software and the Handscope’s complete user

manual.

Also Included:

(1) Test Report

(1) Battery Information Sheet

(6) 1.2V NiMH rechargeable batteries 2700mA/h

Handscope Oscilloscope

Model OX5042

(2) Probe 10:1 600V/BNC-M

Cat. #5000.50

PRODUCT PACKAGING 2150.21

Shipping Contents:

(1) Black Tool Bag

Cat. #2133.72

(1) USB Drive

(software and manual)

(1) Set of two,

color-coded leads and clips

Cat. #2140.63

(1) BNC Adapter

Cat. #2118.46

(1) USB Cable + Driver

Cat. #2135.41

(1) Set of two, color-coded probes

Cat. #2152.23

(1) U.S. Wall Plug 18W,

100-240V, 50/60Hz

Cat. #5000.51

USB DRIVE CONTENTS: The SX-METRO software and the Handscope’s complete user

manual.

Also Included:

(1) Test Report

(1) Battery Information Sheet

(6) 1.2V NiMH rechargeable batteries 2700mA/h

(1) Current Probe MN251T

Cat. #2132.59

(1) USB Drive

(software and manual)

(1) Set of two,

color-coded leads and clips

Cat. #2140.63

(1) BNC Adapter

Cat. #2118.46

(1) Probe 10:1 600V/BNC-M

Cat. #5000.50

(1) USB Cable + Driver

Cat. #2135.41

PRODUCT PACKAGING 2150.22 KIT

Shipping Contents:

(1) Set of two, color-coded probes

Cat. #2152.23

(1) Current Probe MF3000-24-1-1

Cat. #2132.63

(1) Carrying Case

Cat. #2155.77

Handscope Oscilloscope

Model OX5042

(1) U.S. Wall Plug 18W,

100-240V, 50/60Hz

Cat. #5000.51

USB DRIVE CONTENTS: The SX-METRO software and the Handscope’s complete user

manual.

Also Included:

(1) Test Report

(1) Battery Information Sheet

(6) 1.2V NiMH rechargeable batteries 2700mA/h

(1) Current Probe MN379T

Cat. #2153.02

(1) USB Drive

(software and manual)

(1) Set of two,

color-coded leads and clips

Cat. #2140.63

(1) BNC Adapter

Cat. #2118.46

(1) Probe 10:1 600V/BNC-M

Cat. #5000.50

(1) USB Cable + Driver

Cat. #2135.41

PRODUCT PACKAGING 2150.23 KIT

Shipping Contents:

(1) Set of two, color-coded probes

Cat. #2152.23

(1) Current Probe MF3000-24-1-1

Cat. #2132.63

(1) Carrying Case

Cat. #2155.77

Handscope Oscilloscope

Model OX5042

Precautions Before Use

The operator and/or the responsible authority must carefully read and completely

understand the precautions before use. If you use this instrument in an unspeciﬁed

manner, the protection it ensures can be compromised, thus putting you in danger.

• This instrument is designed for use:

-indoors

-in a level 2 pollution environment

-at an altitude below 2000 m

-at a temperature between 0° C and 40° C

-with a relative humidity of less than 80% up to 35° C.

• The safety of all systems, including the instrument, is the responsibility of the

operator.

• It can be used for measurements on 600V CAT III circuits, relative to the ground/

earth.

• Before each use, check the condition of the insulation on the cables, boxes,

sensors and accessories. Any element on which the insulation is damaged

(even partially) must be taken out of service for repair or disposal.

• Respect the environmental and storage conditions.

• The external power supply must be connected to the instrument and to the

network (98 to 264 VAC).

• The power supply to the instrument is ﬁtted with an automatically resettable

electrical protection after disappearance of the fault.

• As a safety measure, only use factory supplied parts and accessories.

• It is advised to use individual safety protection whenever the environmental

situations in which the instrument is used require it.

• When handling the sensors or test probes, do not place your ﬁngers beyond the

physical guard.

• If the battery housing cover is absent, damaged or incorrectly positioned, the

instrument must not be used other than to adjust the sensors.

Deﬁnition of Measurement Categories (CAT)

CAT IV Measurement category IV corresponds to measurements taken at the source

of low-voltage installations.

Example: power feeders, counters and protection devices.

CAT III Measurement category III corresponds to measurements on building installa-

tions.

Example: distribution panel, circuit-breakers, machines or ﬁxed industrial

devices.

CAT II Measurement category II corresponds to measurements taken on circuits

directly connected to low-voltage installations.

Example: power supply to domestic electrical appliances and portable tools.

Symbols Used

CAUTION! Risk of electric shock. The voltage at the

parts marked with this symbol may be dangerous.

Warning: Risk of danger. Refer to the operating manual to ﬁnd out the nature of

the potential hazards and the action necessary to avoid such hazards.

Earth/Ground

Dual insulation

The trash can with a line through it means that in the European Union, the prod-

uct must undergo selective disposal for the recycling of electric and electronic

material, in compliance with Directive WEEE 2002/96/EC.

The CE marking guarantees conformity with European directives and with regu-

lations covering EMC.

Application or withdrawal not authorized for non-insulated conductors carrying

dangerous voltage levels

Power Supply

The oscilloscope is supplied with one external power supply and set of 6 x 1.2V NiMH

rechargeable batteries 2700mA/h.

When the supplied wall plug is connected from the instrument to an external power

source, battery power is not needed. The batteries are only used when there is no

external power supply available.

Before the ﬁrst use, start by fully charging the battery.

NOTE: The batteries automatically begin recharging when the Oscilloscope is powered off, but

connected to an external power supply.

When the batteries are recharging, the Battery Charge LED on the front panel will turn

on steady.

The LED will blink in the following situations:

• pre-charge of very low batteries

• temperature is too low or too high

• batteries are damaged

When the charge is complete, the LED will turn off.

If the batteries need to be replaced, they must be replaced with NiMH rechargeable

batteries. Battery charge life is guaranteed for same-capacity batteries (in mAh) as

those shipped with the oscilloscope.

To remove the battery cover, use a coin to turn the slot on the back of the unit counter-

clockwise.

Description

The Handscope Oscilloscope Model OX5042-CK combines three instruments into one:

• 40MHz oscilloscope

• Independent 8000-count multimeter with power measurements

• Built-in harmonic analyzer out to the 31st harmonic (fundamental between 40

and 450Hz)

The instrument operates at a constant acquisition depth of 2500 points.

An LCD TFT screen is used to view the applied signals along with all the setting

parameters.

The main command functions are accessible using the buttons on the front panel.

A graphic interface is used to:

-adjust the parameters related to the selected button

-navigate using a horizontal main menu showing the current settings and

vertical sub-menus

Channel Isolation

The two oscilloscope input channels are isolated from each other and from the ground/

earth and the main power supply block. This isolation is provided by double or rein-

forced insulation, in compliance with the safety standards IEC 61010-1 and IEC 61010-

2-030.

This makes it possible to make measurements on installations or systems connected to

the electricity supply network for voltages of up to 600V in CAT III. The common mode

authorized between the two channels is 600V in CAT III. Thus the operator, the test

systems and the environment are completely protected at all times.

Any voltage (even dangerous) on one channel will not be present on the other channel.

The low points of the inputs are completely insulated, so there is no possibility of the

low points looping (which can be dangerous and highly destructive).

NOTE: The use of accessories with a voltage and/or category lower than 600V CAT III reduces

the operating range to the lower voltages and/or categories.

The oscilloscope is rated 600V CAT III; at least 600V CAT III accessories must be used.

Control Features

Measurement Terminals

Input

Channel “A”

Input

Channel “B”

External

power

supply

ITEM BUTTON DESCRIPTION

OPERATING MODE BUTTONS

Press these buttons to select the desired operating mode:

- Oscilloscope

- Multimeter

- Harmonic analyzer

NAVIGATION BUTTONS

Use these navigation buttons to move around the menus and dialog

boxes:

VERTICAL

- Vertical movement and automatic selection in the secondary menus

- Adjustment of values in the main menus

- Vertical movement in a dialog box

HORIZONTAL

- Horizontal movement through the main menus

- Adjustment of values in the secondary menus

- Horizontal movement in a dialog box

ENTER

- Opens a dialog box from a main menu or a secondary menu

- Validation of the items in a dialog box

CHANNEL A, B

- A single press selects channel A (or B) and shows the corresponding

menu.

- Pressing twice deselects the channel.

MATH/MEMORY BUTTONS

- A single press selects channel M (Math) and shows the corresponding

menu.

- Pressing twice deselects the channel.

NOTE: For the M (memory) channel, pressing twice invalidates the chan-

nel. Pressing once again selects the Math channel, the memory is lost and

must be reloaded.

ON/OFF BUTTON

- The instrument is turned ON by a short press on this button. It is

turned OFF by a long press (a shutdown message appears and a beep

sounds).

FUNCTION BUTTONS

-Auto Set: Performs an automatic adjustment on channels A and B.

The success of each vertical autoset conditions the activation of the

channel.

-Run Hold: Starts or stops an acquisition.

CHARGE STATUS

- Battery Charge LED

Indice

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente