Agilent Technologies U1452A Manuale utente

Agilent Technologies

Agilent U1452A,

U1452AT, and U1451A

Insulation Tester

User’s Guide

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com

II U1452A/U1452AT/U1451A User’s Guide

Notices

No part of this manual may be reproduced in

any form or by any means (including elec-

tronic storage and retrieval or translation

into a foreign language) without prior agree-

ment and written consent from Agilent

Technologies, Inc. as governed by United

States and international copyright laws.

Manual Part Number

U1451-90003

Edition

First Edition, January 13, 2014

Agilent Technologies, Inc.

5301 Stevens Creek Blvd.

Santa Clara, CA 95051 USA

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connec-

tion with the furnishing, use, or per-

formance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and or software described in

this document are furnished under a license

and may be used or copied only in accor-

dance with the terms of such license.

Restricted Rights Legend

U.S. Government Restricted Rights. Soft-

ware and technical data rights granted to

the federal government include only those

rights customarily provided to end user cus-

tomers. Agilent provides this customary

commercial license in Software and techni-

cal data pursuant to FAR 12.211 (Technical

Data) and 12.212 (Computer Software) and,

for the Department of Defense, DFARS

252.227-7015 (Technical Data - Commercial

Items) and DFARS 227.7202-3 (Rights in

Commercial Computer Software or Com-

puter Software Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and

met.

U1452A/U1452AT/U1451A User’s Guide III

Safety Symbols

The following symbols on the instrument and in the documentation indicate precautions

which must be taken to maintain safe operation of the instrument.

Direct current (DC) Caution, risk of electric shock

Alternating current (AC)

Caution, risk of danger (refer to

this manual for specific Warning

or Caution information)

Both direct and alternating

current

Category III 1000 V overvoltage

protection

Earth (ground) terminal Category IV 600 V overvoltage

protection

Equipment protected throughout

by double insulation or reinforced

insulation

Do not use in distribution systems

with voltages higher than 600 V

CAT III

1000 V

CAT IV

600 V

IV U1452A/U1452AT/U1451A User’s Guide

Safety Considerations

Read the information below before using this tester. Model U1452A appears in all

illustrations.

WARNING

• Do not use the tester if it is damaged. Before you use the tester, inspect the case.

Look for cracks or missing plastic. Pay particular attention to the insulation

surrounding the connectors.

• Inspect the test leads for damaged insulation or exposed metal. Check the test

leads for continuity. Replace damaged test leads before you use the tester.

• Do not operate the tester around explosive gas, vapor, or wet environments.

• Do not apply more than the rated voltage (as marked on the tester) between

terminals, or between terminal and earth ground.

• Before use, verify the tester's operation by measuring a known voltage.

• When servicing the tester, use only the specified replacement parts.

• Use caution when working above 60 VDC, 30 VAC RMS, or 42.4 V peak. Such

voltages pose a shock hazard.

• When using the probes, keep your fingers behind the finger guards on the probes.

• Connect the common test lead before you connect the live test lead. When you

disconnect the leads, disconnect the live test lead first.

• Remove the test leads from the tester before you open the battery cover.

• Do not operate the tester with the battery cover or portions of the cover removed

or loosened.

• To avoid false readings, which may lead to possible electric shock or personal

injury, replace the battery as soon as the low battery indicator appears and

flashes.

• Ensure that you do not perform insulation resistance tests in distribution systems

with voltages higher than 600 V.

• For insulation resistance tests, ensure that you select a suitable test voltage for

the equipment to be tested.

U1452A/U1452AT/U1451A User’s Guide V

CAUTION

•Disconnect circuit power and discharge all high-voltage capacitors before testing

resistance, continuity, or capacitance.

•Use the proper terminals, function, and range for your measurements.

•This device is for use at altitudes of up to 2,000 m.

•Always use the specified battery type. The power for the tester is supplied with four

1.5 V AA batteries. Observe the correct polarity markings before you insert the

batteries to ensure proper insertion of the batteries in the tester.

VI U1452A/U1452AT/U1451A User’s Guide

Environmental Conditions

This instrument is designed for indoor use and in an area with low condensation. The table

below shows the general environmental requirements for this instrument.

Environmental condition Requirement

Te m p e r at u r e

• Operating condition

•–20 °C to 55 °C, 0% to 80% RH (using Alkaline batteries),

20 minutes operating time

• Storage condition

•–40 °C to 70 °C, 0% to 80% RH (without batteries)

Humidity Full accuracy up to 80% RH for temperatures up to 30 °C,

decreasing linearly to 50% RH at 55 °C

Altitude Up to 2,000 meters

Pollution degree Pollution degree II

NOTE

The U1452A/U1452AT/U1451A Insulation Tester complies with the following safety and EMC

requirements:

• Safety compliance

•Designed in compliance to IEC/EN 61010-1:2010 for Category III 1000 V and Category IV 600 V

•Designed in compliance to IEC/EN 61557-1, IEC/EN 61557-2, and IEC/EN 61557-4

• EMC compliance

•Commercial limits compliance with IEC 61326-1:2005/EN 61326-1:2006

U1452A/U1452AT/U1451A User’s Guide VII

Regulatory Markings

The CE mark is a registered trademark

of the European Community. This CE

mark shows that the product complies

with all the relevant European Legal

Directives.

The C-tick mark is a registered

trademark of the Spectrum

Management Agency of Australia. This

signifies compliance with

the Australia EMC Framework

regulations under the terms of the

Radio Communication Act of 1992.

ICES/NMB-001 indicates that this ISM

device complies with the Canadian

ICES-001.

Cet appareil ISM est confomre a la

norme NMB-001 du Canada.

This instrument complies with the

WEEE Directive (2002/96/EC) marking

requirement. This affixed product label

indicates that you must not discard

this electrical or electronic product in

domestic household waste.

The CSA mark is a registered

trademark of the Canadian Standards

Association.

This symbol indicates the time period

during which no hazardous or toxic

substance elements are expected to

leak or deteriorate during normal use.

Forty years is the expected useful life

of the product.

VIII U1452A/U1452AT/U1451A User’s Guide

Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

This instrument complies with the WEEE Directive (2002/96/EC) marking requirement.

This affixed product label indicates that you must not discard this electrical or electronic

product in domestic household waste.

Product Category:

With reference to the equipment types in the WEEE directive Annex 1, this instrument is

classified as a “Monitoring and Control Instrument” product.

The affixed product label is as shown below.

Do not dispose in domestic household waste.

U1452A/U1452AT/U1451A User’s Guide IX

Declaration of Conformity (DoC)

The Declaration of Conformity (DoC) for this instrument is available on the Agilent website.

You can search the DoC by its product model or description at:

http://regulations.corporate.agilent.com/DoC/search.htm

NOTE

If you are unable to search for the respective DoC, please contact your

local Agilent representative.

X U1452A/U1452AT/U1451A User’s Guide

THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Agilent Technologies Apparecchiature di prova

Agilent Technologies

Agilent Technologies E6198B Manuale utente

Agilent Technologies

Agilent Technologies HP 83711A Manuale utente

Agilent Technologies

Agilent Technologies 2000 X Manuale utente

Agilent Technologies

Agilent Technologies 85050B Manuale

Agilent Technologies

Agilent Technologies auroraSonata Manuale utente

Agilent Technologies

Agilent Technologies J2126A Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies 54620 Series Istruzioni operative e di sicurezza

Agilent Technologies

Agilent Technologies 16452A Manuale operativo

Agilent Technologies

Agilent Technologies InfiniiVision 5000 Series Manuale utente

Agilent Technologies

Agilent Technologies U1602B Manuale utente

Agilent Technologies

Agilent Technologies 16048E Manuale operativo

Agilent Technologies

Agilent Technologies N5230AU-974 Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies E5023U Guida rapida

Agilent Technologies

Agilent Technologies InfiniiVision 7000 Series Manuale utente

Agilent Technologies

Agilent Technologies 85056D Manuale

Agilent Technologies

Agilent Technologies Infiniium 90000 Q-Series Manuale

Agilent Technologies

Agilent Technologies 1100 Series Manuale utente

Agilent Technologies

Agilent Technologies E4406A VSA Series Manuale

Agilent Technologies

Agilent Technologies InfiniiVision MSO6104A Guida rapida

Agilent Technologies

Agilent Technologies 16334A Manuale operativo

Agilent Technologies

Agilent Technologies Infiniium DCA Manuale

Agilent Technologies

Agilent Technologies 87075C Option H08 Manuale

Agilent Technologies

Agilent Technologies InfiniiVision 4000 X-Series Manuale utente

Agilent Technologies

Agilent Technologies 16442A Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente

Ritmix

Ritmix RAT-701 Manuale utente