Allen-Bradley CompactLogix EtherNet/IP 1768-EWEB Manuale utente

Installation Instructions

CompactLogix EtherNet/IP Web Server

Module

Catalog Number 1768-EWEB

Topic Page

Important User Information 2

Minimum Spacing 7

What You Need 8

Install the Modules 8

Wire the Module 14

Connect the Module 15

Configure the Module 16

Confirm Your Installation 16

Remove the EtherNet/IP Web Server Module 17

Troubleshoot the Module 18

Status Indicators 19

Specifications 20

Additional Resources 23

AB Drives

2CompactLogix EtherNet/IP Web Server Module

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

mportant User Information

Solid-state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://www.rockwellautomation.com/literature/) describes some important differences between

solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also

because of the wide variety of uses for solid-state equipment, all persons responsible for applying this

equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to

personal injury or death, property damage, or economic loss. Attentions help you identify

a hazard, avoid a hazard and recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, drive or motor,

to alert people that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, drive or motor,

to alert people that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the

product.

CompactLogix EtherNet/IP Web Server Module 3

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

North American Hazardous Location Approval

The following information applies

when operating this equipment in

hazardous locations.

Informations sur l’utilisation de cet

équipement en environnements

dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are

suitable for use in Class I Division 2 Groups A, B, C,

D, Hazardous Locations and nonhazardous

locations only. Each product is supplied with

markings on the rating nameplate indicating the

hazardous location temperature code. When

combining products within a system, the most

adversetemperaturecode(lowest"T"number)may

be used to help determine the overall temperature

code of the system. Combinations of equipment in

your system are subject to investigation by the

local Authority Having Jurisdiction at the time of

installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements

de Classe I Division 2 Groupes A, B, C, D dangereux et

non dangereux. Chaque produit est livré avec des

marquages sur sa plaque d'identification qui indiquent

le code de température pour les environnements

dangereux. Lorsque plusieurs produits sont combinés

dans un système, le code de température le plus

défavorable (code de température le plus faible) peut

être utilisé pour déterminer le code de température

global du système. Les combinaisons d'équipements

dans le système sont sujettes à inspection par les

autorités locales qualifiées au moment de

l'installation.

WARNING:

Explosion Hazard -

•Do not disconnect equipment

unless power has been removed

or the area is known to be

nonhazardous.

•Do not disconnect connections to

this equipment unless power has

been removed or the area is

known to be nonhazardous.

Secure any external connections

that mate to this equipment by

using screws, sliding latches,

threaded connectors, or other

means provided with this product.

•Substitution of components may

impair suitability for Class I,

Division 2.

•If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

AVERTISSEMENT:

Risque d’Explosion –

•Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher

l'équipement.

•Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les

connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou

autres moyens fournis avec ce

produit.

•La substitution de composants peut

rendre cet équipement inadapté à

une utilisation en environnement de

Classe I, Division 2.

•S'assurer que l'environnement est

classé non dangereux avant de

changer les piles.

AB Drives

4CompactLogix EtherNet/IP Web Server Module

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

European Hazardous Location Approval

This equipment is intended for use in potentially explosive atmospheres as

defined by European Union Directive 94/9/EC.

Intertek certifies that this equipment has been found to comply with the

Essential Health and Safety Requirements relating to the design and

construction of Category 3 equipment intended for use in Zone 2 potentially

explosive atmospheres, given in Annex II to this Directive. The examination and

test results are recorded in confidential report No.100014190DAL-001.

Compliance with the Essential Health and Safety Requirements has been

assured by compliance with EN 60079-15.

WARNING: This equipment must be installed in an enclosure

providing at least IP54 protection when applied in Zone 2

environments.

Provision shall be made to prevent the rated voltage from being

exceeded by transient disturbances of more than 40% when applied in

Zone 2 environments.

CompactLogix EtherNet/IP Web Server Module 5

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

Environment and Enclosure

ATTENTION: This equipment is intended for use in a Pollution

Degree 2 industrial environment, in overvoltage Category II

applications (as defined in IEC 60664-1), at altitudes up to 2000 m

(6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment

according to IEC/CISPR 11. Without appropriate precautions, there

may be difficulties with electromagnetic compatibility in residential

and other environments due to conducted and radiated disturbances.

This equipment is supplied as open-type equipment. It must be

mounted within an enclosure that is suitably designed for those

specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from

accessibility to live parts. The enclosure must have suitable

flame-retardant properties to prevent or minimize the spread of flame,

complying with a flame spread rating of 5VA, V2, V1, V0 (or

equivalent) if non-metallic. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain

product safety certifications.

In addition to this publication, see:

•Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for additional installation

requirements.

•NEMA Standard 250 and IEC 60529, as applicable, for

explanations of the degrees of protection provided by different

types of enclosure.

AB Drives

6CompactLogix EtherNet/IP Web Server Module

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

Prevent Electrostatic Discharge

ATTENTION: This equipment is sensitive to electrostatic

discharge, which can cause internal damage and affect normal

operation. Follow these guidelines when you handle this

equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•If available, use a static-safe workstation.

•When not in use, store the equipment in appropriate static-safe

packaging.

CompactLogix EtherNet/IP Web Server Module 7

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

Minimum Spacing

Plan for this minimum spacing from enclosure walls, wireways, and other

equipment.

See Specifications on page 20 for the temperature range.

Item Description

1 105 mm (4 in.)

2 90 mm (3.54 in.)

31609-M

Power

OUT

L2/N

AB Drives

8CompactLogix EtherNet/IP Web Server Module

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

What You Need

Install the Modules

Item Cat. No. or Size

1768 CompactLogix power supply 1768-PA3

1768 CompactLogix controller 1768-L43

1769 end cap

Connects to the controller as the

last module, either:

•without any 1769-series

modules attached to the

controller (1768-series only)

•with a combination of

1768-series and 1769-series

modules attached to the

controller

1769-ECR

RJ45 Ethernet connector See Wire the Module on page 14

DIN rail or mounting screws (one

or the other but not both) DIN rail Either of these sizes:

•35 x 7.5 mm (EN 50 022 - 35 x 7.5)

•35 x 15 mm (EN 50 022 - 35 x 15)

Screws M4 or #8 panhead screws

ATTENTION: This product is grounded through the DIN rail to

chassis ground. Use zinc-plated yellow-chromate steel DIN rail to

assure proper grounding. The use of other DIN rail materials (for

example, aluminum or plastic) that can corrode, oxidize, or are

poor conductors, can result in improper or intermittent grounding.

Secure DIN rail to mounting surface approximately every 200 mm

(7.87 in.) and use end-anchors appropriately.

CompactLogix EtherNet/IP Web Server Module 9

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

If You Are Using Screws to Mount Your Modules

The steps in these instructions show how to mount the modules on DIN rail.

If you are using screws instead of DIN rail, make these changes to the

instructions.

1. Follow the steps in Mount the Controller on the DIN Rail on page 10 to

connect the modules together.

2. Use the modules as a template and mark pilot holes on your panel.

3. Drill the pilot holes for M4 or #8 screws.

4. Use M4 or #8 screws to mount the modules to your panel. Use 1.16

N•m (10 lb•in) of torque.

5. Ground the module on a ground bus with a dedicated earth ground

stake.

6. Connect the ground bus to a functional earth ground on the DIN rail or

panel.

7. Refer to Industrial Automation Wiring and Grounding Guidelines,

publication 1770-4.1, for additional information.

IMPORTANT Do not use screws and DIN rail to mount the modules. It is

possible to break the mounting tabs off if you screw the modules

to the panel while they are on DIN rail

AB Drives

10 CompactLogix EtherNet/IP Web Server Module

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

Install the DIN Rail

Mount the DIN rail in a suitable location.

Mount the Controller on the DIN Rail

1. Close the DIN rail latches on the controller.

ATTENTION: This product is grounded through the DIN rail to

chassis ground. Use zinc plated yellow-chromate steel DIN rail to

assure proper grounding. The use of other DIN rail materials (for

example, aluminum or plastic) that can corrode, oxidize, or are poor

conductors, can result in improper or intermittent grounding.

Secure DIN rail to mounting surface approximately every 200 mm

(7.8 in.) and use end-anchors appropriately.

Indice

Altri manuali Allen-Bradley Unità di controllo

Allen-Bradley

Allen-Bradley ControlLogix 1756-ENBT Manuale utente

Allen-Bradley

Allen-Bradley CENTERLINE 2100 Manuale utente

Allen-Bradley

Allen-Bradley ControlNet ControlLogix 1756 Manuale utente

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IP4 Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix ControlNet B Series Manuale utente

Allen-Bradley

Allen-Bradley 1757-ABRIO Manuale utente

Allen-Bradley

Allen-Bradley A Series Manuale utente

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Manuale operativo

Allen-Bradley

Allen-Bradley ControlNet-to-DeviceNet 1788-CN2DN Manuale utente

Allen-Bradley

Allen-Bradley 1203-GD1 Manuale elenco delle parti

Allen-Bradley

Allen-Bradley 1407-CGCM Manuale utente

Allen-Bradley

Allen-Bradley 1770-KFDG Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-ADN Manuale utente

Allen-Bradley

Allen-Bradley C Series Manuale utente

Allen-Bradley

Allen-Bradley C Series Manuale utente

Allen-Bradley

Allen-Bradley Rockwell Automation 1734-4IOL Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Manuale utente

Allen-Bradley

Allen-Bradley 1769-OF8C Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Manuale utente

Allen-Bradley

Allen-Bradley 1757-ABRIO Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix 1756-OF6VI Manuale utente

Allen-Bradley

Allen-Bradley CAB6-HA 3 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente