Allen-Bradley ControlNet-to-DeviceNet 1788-CN2DN Manuale utente

1788-5.2B - October 1999

Installation Instructions

ControlNet-to-DeviceNet Linking Device

Catalog No. 1788-CN2DN

Product Overview

The ControlNet-to-DeviceNet (CN2DN) linking device connects a ControlNet™

network to a DeviceNet™ network. The DeviceNet network consists of multiple

DeviceNet devices, such as RediSTATIONs, photoeyes, etc. The ControlNet

network consists of controllers, such as PLC® processors, HMIs, drives, I/O

devices, and so on.

The CN2DN linking device has two broad functions, supporting closed-loop

control, and configuration and monitoring.

To the Installer

Use this document as a guide when you install the 1788-CN2DN.

Topic Page

System Requirements 3

CN2DN Hardware Description 4

Installing the CN2DN Module 4

ControlNet Connections 6

DeviceNet Connections 9

Setting the DNet Data Rate 11

Setting the Node Address Switches 10

The Example Installation 12

RSLogix5000™ Setup 12

ControlNet Setup Using RSNetWorx for ControlNet 17

DeviceNet Setup Using RSNetWorx for DeviceNet 21

Interpreting the Status Indicators 27

Compliance to European Union Directives 31

CSA Hazardous Location Approval 32

Specifications 34

Allen-Bradley Parts

2ControlNet-to-DeviceNet Linking Device

1788-5.2B - October 1999

Handling the CN2DN

We recommend that you adhere to this precautionary information.

Precautionary Statements - Important User Information

Because of the variety of uses for the products described in this publication, those

responsible for the application and use of this control equipment must satisfy

themselves that all necessary steps have been taken to assure that each

application and use meets all performance and safety requirements, including any

applicable laws, regulations, codes, and standards.

The illustrations, charts, sample programs, and layout examples shown in this

guide are intended solely for purposes of example. Since there are many

variables and requirements associated with any particular installation,

Allen-Bradley does not assume responsibility or liability (to include intellectual

property liability) for actual use based upon the examples shown in this

publication.

Allen-Bradley publication SGI-1.1, Safety Guidelines for the Application,

Installation, and Maintenance of Solid State Control (available from your local

Allen-Bradley office), describes some important differences between solid-state

equipment and electromechanical devices that should be taken into consideration

when applying products such as those described in this publication.

Reproduction of the contents of this copyrighted publication, in whole or in part,

without the written permission of Allen-Bradley Company, Inc., is prohibited.

!ATTENTION: This module contains ESD (Electrostatic

Discharge) sensitive parts and assemblies. Static control

precautions are required when installing or testing this assembly.

Component damage may result if these procedures are not

followed.

ControlNet-to-DeviceNet Linking Device 3

1788-5.2B - October 1999

System Requirements

This section describes the required hardware and software components you need

before you can use the CN2DN linking device.

Hardware

•ControlNet-to-DeviceNet linking device

•PC access to ControlNet through RSLinx™

•ControlNet and DeviceNet cabling

Software

•Windows NT® 4.0 with service pack 3 or higher

•RSLinx 2.10 or later; this is the driver for the Allen-Bradley PC interfaces.

•RSNetWorx™ for ControlNet version 2.0 or later; this is the ControlNet

configuration tool.

•RSNetWorx™ for DeviceNet version 2.11 or later; this is the DeviceNet

configuration tool.

Compatibility Information

The 1788-CN2DN linking device is compatible with DeviceNet and ControlNet

specifications as of this writing.

Related Publications

Title Publication Number

ControlNet Cable System, Planning and Installation Manual 1786-6.2.1

DeviceNet Cable System, Planning and Installation Manual DN-6.7.2-MAY99

ControlLogix ControlNet Bridge Installation Manual 1756-5.71

ControlLogix ControlNet Interface Module User Manual 1756-6.5.3

Allen-Bradley Parts

4ControlNet-to-DeviceNet Linking Device

1788-5.2B - October 1999

CN2DN Hardware Description

Figure 1 shows the components of the CN2DN linking device.

Figure 1 CN2DN Linking Device

The CN2DN module is designed to be mounted on a 35 mm steel DIN rail. End

anchors are provided to keep the module in position.

The device has one ControlNet port with support for redundant media as well as

a ControlNet network access port. Rotary switches are used to set the ControlNet

node address. The CNet Status LEDs display the current status of each of the

redundant media channels.

The CN2DN has one DeviceNet port. Rotary switches are used to set the

DeviceNet node address and the data rate. DNet LEDs display the current status

of the network and the I/O channel.

Module Status and Linking Activity LEDs are also provided. For information

about the LEDs, see “Interpreting the Status Indicators” beginning on page 27.

The power supply connector is wired to 24V dc.

30901-M

Status LEDs

Power Supply

Connector

ControlNet Port

Network

Access

Port

DeviceNet

Port

Rotary

Switches

End Anchor End Anchor

DIN Rail

ControlNet-to-DeviceNet Linking Device 5

1788-5.2B - October 1999

Installing the CN2DN Module

The CN2DN module has a clip for mounting on a standard 35 mm steel DIN rail.

Follow these steps to mount the CN2DN onto the DIN rail.

Important: You must use a steel DIN rail (A-B P/N 199-DR1 or equivalent) to

meet vibration specifications listed on page 34.

1. Press the module straight onto the DIN rail at the desired location. Be sure

that both latches snap into place.

Figure 2 Mounting the CN2DN Module on the DIN Rail

2. Use the supplied end anchors to lock the module into place.

Figure 3 End Anchors and Mounting Tabs

Note that for very high shock applications the module may be bolted to the panel

through the four mounting tabs on the base.

DIN Rail

CN2DN Module

PRESS ON

Wall or Support

30901-M

Mounting Tabs

End Anchor

Allen-Bradley Parts

6ControlNet-to-DeviceNet Linking Device

1788-5.2B - October 1999

Removing the CN2DN module

To remove the CN2DN module, simultaneously pull the 2 DIN rail latches away

from the rail and pull the module off the panel. (Note: This may require two

screwdrivers to open the latches.)

Connecting Power

The CN2DN linking device requires 18-26V dc input power. The CN2DN filters

and regulates the supplied power. The power connector is a 4-pin redundant

screw terminal connector. The pinout for the power connector is shown in

Figure 4.

Figure 4 Power Connector Pinout

Connect the primary power supply to the left + and - pair. The right + and - pair

may be used to chain the primary power supply to other devices.

Important: The connection to downstream devices will not be made unless the

connector is plugged in to the CN2DN.

ControlNet Connections

BNC Connectors

The BNC connectors on the unit should be connected to a ControlNet network

through a tap. The BNC connectors must be used to connect the CN2DN linking

device to the ControlNet network.

30906-M

+ - + -

ControlNet-to-DeviceNet Linking Device 7

1788-5.2B - October 1999

Refer to publication number 1786-6.2.1, ControlNet Cable System Planning and

Installation Manual, for further information.

Figure 5 ControlNet Connections

Network Access Port (NAP)

The CN2DN includes a Network Access Port (NAP) with an RJ-45 connector for

connecting programming terminals to devices on the ControlNet network. You

can use the NAP to temporarily connect a device such as a laptop computer to the

network.

Important: Do not connect the CN2DN to more than one ControlNet network

at a time. Attempting to connect to a second network will cause the

CN2DN to operate erratically.

!ATTENTION: If you connect the product to a cable system that

does not support redundant media, connect the tap dropline to the

BNC connector labeled channel A. channel B is left open when

using single media.

If the cable system is redundant, connect all channel A connectors

to one cable, and all channel B connectors to the other cable.

30904-M

Network Access Port (NAP)

BNC Connectors

Allen-Bradley Parts

8ControlNet-to-DeviceNet Linking Device

1788-5.2B - October 1999

Figure 6 shows an example of a typical ControlNet network connection.

Figure 6 Typical CN2DN Connections to a ControlNet Network

trunk cable A =

trunk cable B =

30907-M

ControlNet Device

Linking

Device

ControlNet-to-DeviceNet Linking Device 9

1788-5.2B - October 1999

DeviceNet Connections

The location of the DeviceNet connector is shown in figure 7.

Figure 7 DeviceNet Connector on the CN2DN

Use an open-style 5- or 10-position linear plug to connect to the DeviceNet

network. An open-style 10-position linear plug is provided with your CN2DN.

Wire the connector as shown in figure 8.

Figure 8 Connector Pinout to CN2DN

Refer to publication number DN-6.7.2, DeviceNet Cable System Planning and

Installation Manual, for further information.

30902-M

DeviceNet Connector

Black

Blue

White

Red

Bare

DeviceNet Drop Line

Red

White

Clear

Blue

Black

10-position pluge 5-position pluge

30919-M

Allen-Bradley Parts

10 ControlNet-to-DeviceNet Linking Device

1788-5.2B - October 1999

Setting the Node Address Switches

Important: When using a 1788-CN2DN, the ControlNet network must have an

“Active Keeper” to keep track of network scheduling, clock

synchronization, etc.

Refer to publication 1756-5.71, ControlLogix ControlNet Bridge, for

information on configuring a 1756-CNB module.

CN2DN ControlNet Address

Choose and set a ControlNet network address for the CN2DN. Refer to figure 9.

Important: ControlNet addresses must be in the range 01-99.

Figure 9 CNet Node Address Switches

CN2DN DeviceNet Address

Choose and set a DeviceNet network address for the CN2DN. Refer to figure 10:

Important: DeviceNet addresses must be in the range 00-63.

Figure 10 DNet Node Address Switches

Indice

Altri manuali Allen-Bradley Unità di controllo

Allen-Bradley

Allen-Bradley CENTERLINE 2100 Manuale utente

Allen-Bradley

Allen-Bradley 1785-KE Manuale utente

Allen-Bradley

Allen-Bradley Bulletin 1203 Series Manuale utente

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IP4 Manuale utente

Allen-Bradley

Allen-Bradley Bulletin 193 E1 PLUS Guida utente

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OB4D Manuale utente

Allen-Bradley

Allen-Bradley 1732ES-IB16 Manuale utente

Allen-Bradley

Allen-Bradley MicroLogix 1762-OW Manuale utente

Allen-Bradley

Allen-Bradley Kinetix 5700 Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix 1756-IA8D Manuale utente

Allen-Bradley

Allen-Bradley 1746-HSCE Manuale utente

Allen-Bradley

Allen-Bradley 1771-OFE Manuale utente

Allen-Bradley

Allen-Bradley 1747-SN Manuale utente

Allen-Bradley

Allen-Bradley 1203-GD2 Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock Series Manuale

Allen-Bradley

Allen-Bradley XM-124 Manuale utente

Allen-Bradley

Allen-Bradley 1756-M02AS Manuale utente

Allen-Bradley

Allen-Bradley CAB6-HA 3 Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Manuale utente

Allen-Bradley

Allen-Bradley 1757-FFLD Manuale utente

Allen-Bradley

Allen-Bradley 1771-ODD Manuale utente

Allen-Bradley

Allen-Bradley Kinetix 5700 Manuale utente

Allen-Bradley

Allen-Bradley 1407-CGCM-DLR Manuale utente

Allen-Bradley

Allen-Bradley PowerFlex 755 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente