American Dynamics AD615 Manuale utente

Manchester User Instructions

8000-2614-01, Rev. B AMERICAN DYNAMICS PRODUCTS 1

DeltaDome™

Programmable

Surveillance Camera

Contents

Overview................................................................1

Command Summary..............................................2

Working with Presets and Patterns........................2

Defining Presets (Shots) ....................................2

Calling Presets ...................................................2

Defining Patterns................................................2

Running Patterns................................................3

Repeating Patterns.............................................3

Using Other Dome Features..................................3

Dome Flip...........................................................3

Resuming Auto Focus / Auto Iris........................3

Resetting the Dome............................................3

Adjusting Vertical Phase.....................................3

Start Dome Configuration Menu.........................3

Controlling Auxiliaries.............................................4

Overview

The DeltaDome programmable surveillance

camera supports special menus and programming

features via keystroke combinations. This

document describes how to program and use the

special features supported by the dome when

installed in a Manchester network.

Additional Documentation

The dome installation is covered in the following

document:

•DeltaDome Surveillance Camera Installation

Guide, 8000-2616-01

Using the on-screen configuration utility is

described in the following documents:

•DeltaDome Surveillance Camera Configuration

Utility Operator’s Manual, 8000-2612-02

•Delta Dome Surveillance Camera Configuration

Utility Quick Reference Guide, 8000-2613-02

If you need assistance...

Contact the AD/Sensormatic CCTV System

Division at:

1-800-442-2225 (or 914-348-3479).

AD, American Dynamics, DeltaDome, and the AD logo are

trademarks of Sensormatic Electronics Corporation. Other

product names (if any) mentioned herein may be trademarks

or registered trademarks of other companies.

No part of this guide may be reproduced in any form without

written permission from Sensormatic Electronics Corporation.

BSL 8/98

2 MANCHESTER USER INSTRUCTIONS DELTADOME PROGRAMMABLE SURVEILLANCE CAMER

8000-2614-01, REV.

Command Summary

The following tables summarize the special

commands available when using the dome in a

Manchester network. These commands are

available when you enter the number listed and

press the Set Preset or Call Preset button on the

controller. Refer to the instructions in this

document for specific information about using the

commands.

Set Commands: This table describes the

functions that can be performed when you enter

the number listed then press the Set Preset button.

Command Function

65 Set Preset Reset Dome

66 Set Preset Starts Dome Configuration Menu

67 Set Preset Activate / Deactivate V-phase

delay setting adjustment

68 Set Preset Cancel Pattern Programming

69 Set Preset Save Pattern Programming

70 Set Preset Program Pattern 1

71 Set Preset Program Pattern 2

72 Set Preset Program Pattern 3

Call Commands: This table describes the

functions that can be performed when you enter

the number listed then press the Call Preset button.

Command Function

66 Call Preset Resume Auto Focus / Auto Iris

67 Call Preset Rotate dome 180°from current

position (“flip”)

69 Call Preset Repeats following pattern

70 Call Preset Run Pattern 1

71 Call Preset Run Pattern 2

72 Call Preset Run Pattern 3

Working with Presets and

Patterns

This section describes how to program and call the

presets and patterns supported by the dome.

Defining Presets (Shots)

Presets, also called shots or targets, are

programmed video scenes, based on specific pan,

tilt, zoom and focus settings. The dome supports

up to 64 presets when used on a Manchester

network.

To program presets, do the following:

1. Ensure that your camera controller is in

programming mode. Refer to your controller

documentation for additional information.

2. Adjust the position of the dome until you see

the scene that you want to program. Adjust the

zoom, focus, and iris settings if necessary.

3. Use the numeric keypad on the camera

controller to enter the number (1-64) of the

preset you are programming, then press Set

Preset.

For example, to program Preset 12, you would

press, 1,2, then Set Preset.

Calling Presets

To display the preset, do the following:

1. Select the monitor where you want the preset

appear.

2. Use the numeric keypad on the camera

controller to enter the preset number (1-64),

then press Call Preset.

Defining Patterns

A pattern is a sequential series of pan, tilt, zoom,

and focus movements from a single programmable

dome. You "teach" the dome a combination of

these movements that can be replayed

automatically. The dome supports up to three

patterns using presets 70, 71, and 72. To program

a pattern, do the following:

1. Ensure that your camera controller is in

programming mode. Refer to your controller

documentation for additional information.

2. Move the dome to the starting point of the

pattern. Adjust the zoom, focus, and iris

settings if necessary.

3. Use the keypad to enter the number associated

with the pattern (70, 71, or 72), then press Set

Preset.

4. Move the camera around to create the pattern.

Note: If you make a mistake while

programming the pattern, enter 68, then press

Set Preset. This ends the pattern without saving

it. Return to step 1 to start programming again.

5. When you complete the pattern, press 69, then

Set Preset to save the pattern.

DELTADOME PROGRAMMABLE SURVEILLANCE CAMERA

8000-2614-01, REV. B MANCHESTER USER INSTRUCTIONS 3

Running Patterns

To run a pattern, do the following:

1. Select the monitor where you want the pattern

to run.

2. Use the keypad to the enter the number (70,

71, or 72) associated with the pattern, then

press Call Preset.

The pattern runs one time.

Repeating Patterns

To run a pattern repeatedly, do the following:

1. Select the monitor where you want the pattern

to run.

2. Use the keypad to the enter 69, then press Call

Preset.

3. Use the keypad to enter the number (70, 71, or

72) associated with the pattern, then press Call

Preset.

The pattern repeats until a camera movement

command is issued for the dome.

Using Other Dome Features

This section describes how to flip the dome,

resume auto focus and auto iris modes, reset the

dome, adjust the v-phase, and start the dome

configuration menu.

Dome Flip

You can manually rotate the dome 180-degrees

from its current direction by entering 67, then

pressing Call Preset.

Resuming Auto Focus / Auto Iris

The dome normally operates in auto focus and

auto iris mode. However, if you manually adjust the

focus or iris, it switches to manual focus or manual

iris mode. To resume auto focus or auto iris mode,

enter 66, then Call Preset from the camera

controller.

Resetting the Dome

If your dome is not responding to camera

commands, it may be necessary to reset the

dome. To reset the dome, do the following:

1. Ensure that your camera controller is in

programming mode. Refer to your controller

documentation for additional information.

2. Select the number for the Dome using the

numeric keypad, then press Camera (Cam).

3. Use the numeric keypad on the camera

controller to enter 65, then press Set Preset.

Adjusting Vertical Phase

If you experience screen rolling when you switch

cameras, you can adjust the vertical phase (V-

phase) setting of the dome. To adjust the V-phase

setting, do the following:

1. Ensure that your camera controller is in

programming mode. Refer to your controller

documentation for additional information.

2. Use the numeric keypad on the camera

controller to enter 67, then press Set Preset.

3. To change the V-phase delay setting, use the

Iris Open and Iris Close buttons.

-Press

Iris Open to increase the delay.

- Press

Iris Close to decrease the delay.

4. When finished adjusting the V-phase setting,

press 67, then Set Preset.

Start Dome Configuration Menu

Your dome provides special programming menus

to set special features for your dome. To display

these menus, do the following:

1. Ensure that your camera controller is in

programming mode. Refer to your controller

documentation for additional information.

2. Use the numeric keypad on the camera

controller to enter 66, then press Set Preset.

Refer to the information found in the DeltaDome

Surveillance Camera Configuration Utility

Operator’s Manual or Quick Reference Guide for

specific instructions on using the menus.

4 MANCHESTER USER INSTRUCTIONS DELTADOME PROGRAMMABLE SURVEILLANCE CAMER

8000-2614-01, REV.

Controlling Auxiliaries

Auxiliaries, also called outputs, are external

devices, such as lights, audible alarms, or door

locks, that can be operated via the camera

controller when they are connected to a dome or

the video matrix switcher. Auxiliaries can also be

initiated automatically in response to an alarm

when they have been configured to do so. The

DeltaDome programmable surveillance camera

provides four connections for auxiliaries. When

used on a Manchester network, Auxiliaries 1

through 3 are supported. Auxiliary 4 will not work.

The DeltaDome programmable surveillance

camera supports three latching auxiliaries. A

latching auxiliary remains activated until it is

manually deactivated. For example if the auxiliary

is a light, the light remains on until it is manually

turned off.

To manually operate an auxiliary, do the following:

1. Select the dome to which the auxiliary is

connected.

2. Press the number (1-3) for the auxiliary you

want to control.

3. To activate the auxiliary, press Auxiliary On.

To deactivate the auxiliary, press Auxiliary Off.

Altri manuali per AD615

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali American Dynamics Telecamera di sicurezza

American Dynamics

American Dynamics SpeedDome Optima Manuale utente

American Dynamics

American Dynamics SpeedDome Ultra Manuale

American Dynamics

American Dynamics IP speedDome Ultra 8 Manuale

American Dynamics

American Dynamics ADCPBW Manuale utente

American Dynamics

American Dynamics Tyco ADC520 Series Manuale utente

American Dynamics

American Dynamics IP speedDome Ultra 8 Istruzioni di installazione e manutenzione

American Dynamics

American Dynamics SensorRail IIIe ADRL3TRK Series Manuale utente

American Dynamics

American Dynamics ADSDUPIHC Manuale utente

American Dynamics

American Dynamics IP speedDome Ultra 8 Istruzioni di installazione e manutenzione

American Dynamics

American Dynamics Illustra 625 PTZ Manuale utente

American Dynamics

American Dynamics ADC710 Manuale utente

American Dynamics

American Dynamics ADCI625-P221 Manuale utente

American Dynamics

American Dynamics ADCDW Series Manuale utente

American Dynamics

American Dynamics Illustra Flex Series Manuale utente

American Dynamics

American Dynamics ADC500 Manuale utente

American Dynamics

American Dynamics SpeedDome Ultra VI Istruzioni di installazione e manutenzione

American Dynamics

American Dynamics Illustra Flex Series Manuale utente

American Dynamics

American Dynamics illustra 600 Manuale utente

American Dynamics

American Dynamics SpeedDome Optima LT Manuale utente

American Dynamics

American Dynamics ADCIPE3712OCN Manuale utente

American Dynamics

American Dynamics Illustra Flex Series ADCi600F-W012** Manuale utente

American Dynamics

American Dynamics Illustra 625 PTZ Manuale utente

American Dynamics

American Dynamics SpeedDome Ultra VII EIS Istruzioni di installazione e manutenzione

American Dynamics

American Dynamics RASO series Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente