Analog Devices LTC5597 Manuale utente
1
DEMO MANUAL DC3129A-KIT
Rev. 0
DESCRIPTION
LTC5597 Linduino Shield 100MHz to
70 GHz RMS Power Detector
Demonstration circuit DC3129A-KIT is a Linduino
®
evalu-
ation kit for RMS Power Detector LTC
®
5597. It is set up
for quick evaluation of RMS RF power measurement using
the Arduino/Linduino compatible platform and software
download available. When connected to PC with USB
cable, accurate power level can be monitored using the
graphic user interface.
The LTC5597 is a wide dynamic range linear-in-dB RMS
RF Power Detector, operational from 100MHz to 70GHz.
The Linduino (DC2026C) platform provides 10-bit ADC at
4.9mV/LSB resolution with 5V default reference voltage.
Input dynamic range with 1dB accuracy is up to 35dB
depending on frequency. The detector output slope is
normally 6 LSB/dB. The DC3129A-KIT is optimized for
wide operational frequency signals up to 70GHz using
the 1.85mm edge mount connector. Input impedance is
internally matched to 50Ω. It is suitable for RMS mea-
surements of high crest factor waveforms up to 12dB
peak-to-average. No external coupling capacitor is neces
-
sary if DC voltage at RFIN pin is kept below 1.0V. On board
All registered trademarks and trademarks are the property of their respective owners.
(Note 1)
Supply Voltage(VCC): +3.8V
DC Voltage at RFIN: –0.3V to 1.0V
DC Voltage at FLTR: –0.3V to 0.4V
DC Voltage at EN: –0.3V to 3.8V
RFIN Input Power-Average: +15dBm
TJMAX 150°C
Case Operating Temperature Range –40°C to 105°C
Storage Temperature Range –65°C to 150°C
Note 1:Voltage on all pins must not exceed VCC+0.3V
or be less than –0.3V.
CAUTION: This part is sensitive to electrostatic discharge
(ESD). Observe proper ESD precautions when handling
the LTC5597.
TEST SETUP
ABSOLUTE MAXIMUM INPUT RATINGS
3.3V regulator provides power to the shield by jumper
JP1. Contact applications support for more information.
Design files for this circuit board are available.
Figure1. Test Setup for RF Performance Measurements
2
DEMO MANUAL DC3129A-KIT
Rev. 0
NOTES ON TEST EQUIPMENT AND SETUP
1. Remove the DC3129A-KIT from its protective packag-
ing in an ESD-safe working area, connect USB cable
to PC(see Figure1).
2. Set JP1 which provides the 3.3V to VCC by the on board
regulator.
3. Download and install QuikEval if it’s not yet installed.
4. The Eval Kit comes with a Linduino board pre-loaded
with firmware. Follow Figure2 to re-load the firmware
if necessary, which can be downloaded from www.
analog.com.
5. Follow instruction from QuikEval which will automati-
cally update the GUI.
6. Connect USB cable from PC to Linduino board. Con-
nect the RF input to the signal generator at the 1.85mm
connector, J1.
7. Set the frequency and power level (less than +10dBm)
of the signal generator.
8. Open QuikEval, and set the frequency of signal to be
measured. Push “READ” to measure RF power. Using
the default calibration would be loading the nominal
slope and intercept from LTC5597 data sheet values.
See Figure3.
9. Forhigheraccuracy,Calibrationcanbeperformed using
the GUI at various frequency with two point calibration.
Set input power level to the corresponding calibration
points on the GUI, and calibrate accordingly by clicking
the corresponding button.
10. Read RF power using the GUI.
QUICK START PROCEDURE
DEMO BOARD USAGE NOTES
n
Use a high performance signal generator with accu-
rate output power levels up to 70GHz, such as Agilent
E8257D.
n
DC3129A-KIT includes Linduino DC2026C, and the
demo board DC3128A assembled with1.85mm con-
nector for best performance up to 70GHz.
nConnecting cable for RF signal should be rated up to
70GHz for the best performance.
n
Optional input attenuation can be used to improve
return loss, but also shifts the log intercept point
accordingly.
1. Evaluation DC3129A-KIT has provisions for inter-stage
filter cap. Additional capacitor (C3) can be added to
slow down the transient response to reduce the output
ripple. The range for C3 is 10pF to 1nF.
2. Output power is calculated using slope and intercept.
3. ADC count • 4.9mV/slope+intercept=output power.
Slope is derived from two point calibration in the linear
region of transfer function.
4. A minimum two point calibration is necessary for most
applications. Additional calibration points will improve
the accuracy of the power detection.
4
DEMO MANUAL DC3129A-KIT
Rev. 0
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 1 C1 CAP., CX Series, (16kHz to 40GHz), 0.1µF, YD, 16V,
10%, 0402
MURATA, 935152424610-T3N
2 2 C3, C14 CAP., 0.01µF, X7R, 16V, 10%, 0402 MURATA, GRM155R71C103KA01D
NIC, NMC0402X7R103K16TRPF
3 1 C4 CAP., 1µF, X5R, 10V, 10%, 0402 MURATA, GRM155R61A105KE15D
AVX, 0402ZD105KAT2
TDK, C1005X5R1A105K050BB
4 1 C8 CAP., 10pF, NP0, 50V, 10%, 0402 AVX, 04025A100KAT2A
5 0 C10 CAP., OPTION, 0402
6 2 C11, C15 CAP., 0.1µF, X7R, 16V, 10%, 0402 AVX, 0402YC104KAT2A
Taiyo Yuden, EMK105B7104KV-F
TDK, C1005X7R1C104K050BC
7 2 C12, C13 CAP CER 10UF 6.3V X5R 0402 TDK Corporation, C1005X5R0J106M050BC
8 5 E1, E2, E3, E4, E5 TEST POINT, TURRET, 0.064", MTG. HOLE MILL-MAX, 2308-2-00-80-00-00-07-0
9 1 J1 CONN., SMA, 1.85mm, JACK TO EDGE LUNCH, DC-67GHz SOUTHWEST MICROWAVE 1892-03A-6
10 1 J2 CONN., HDR, FEMALE, 1x10, 2.54mm, THT, STR SULLINS CONNECTOR SOLUTIONS, PPPC101LFBN-RC
11 2 J3, J4 CONN., HDR, FEMALE, 1x8, 2.54mm, STR, THT SULLINS CONNECTOR SOLUTIONS, PPPC081LFBN-RC
12 1 J5 CONN., HDR., FEMALE, 1x6, 2.54mm, THT, STR SULLINS CONNECTOR SOLUTIONS, PPPC061LFBN-RC
13 1 J6 CONN., TERM. BLOCK, RCPT, 1x2, 5mm, SIDE ENTRY,
THT
TE CONNECTIVITY, 282836-2
14 2 JP1, JP2 CONN., HDR, MALE, 1x2, 2mm, VERT, STR, THT, 10u"
AU
SAMTEC, TMM-102-02-L-S
15 1 LB1 LABEL SPEC, DEMO BOARD SERIAL NUMBER BRADY, THT-96-717-10
16 1 PCB1 PCB, DC3128A ANALOG DEVICES INC., 600-DC3128A
17 1 R1 RES., AEC-Q200, 2k OHMS, 1%, 1/16W, 0402 VISHAY, CRCW04022K00FKED
NIC, NRC04F2001TRF
18 1 R2 RES., 1 OHM, 1%, 1/16W, 0402 VISHAY, CRCW04021R00FKED
19 0 R8, R14 RES., OPTION, 0402
20 3 R9, R10, R11 RES., 4.99k OHMS, 1%, 1/16W, 0402 NIC, NRC04F4991TRF
VISHAY, CRCW04024K99FKED
YAGEO, RC0402FR-074K99L
21 1 R12 RES., 100 OHMS, 1%, 1/16W, 0402 NIC, NRC04F1000TRF
YAGEO, RC0402FR-07100RL
22 1 R13 RES., 3k OHMS, 5%, 1/16W, 0402 VISHAY, CRCW04023K00JNED
23 1 STNCL1 TOOL, STENCIL, 700-DC3128A ANALOG DEVICES INC., 830-DC3128A
24 1 U1 IC, 100MHz to 70GHz Linear-in-dB RMS Power
Detector with 35dB Dynamic Range
LINEAR TECH, LTC5597_DC#PBF
25 1 U2 IC, LOW NOISE, LDO MICROPOWER REG., TSOT23-5 LINEAR TECH., LT1761ES5-3.3#PBF
LINEAR TECH., LT1761ES5-3.3#TRPBF
26 1 U3 IC, MEMORY, EEPROM, 2Kb (256x8), TSSOP-8,
400kHz
MICROCHIP, 24LC025-I/ST
MICROCHIP, 24LC025T-I/ST
5
DEMO MANUAL DC3129A-KIT
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
SCHEMATIC DIAGRAM
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
1. ALL RESISTORS ARE IN OHMS, 0402
2. ALL CAPACITORS ARE IN MICROFARADS, 0402
NOTE: UNLESS OTHERWISE SPECIFIED
DATE
REV DESCRIPTION APPROVED
ANDY M.
REVISION HISTORY
1 PRODUCTION 06-05-20
3.3V
5V
3.3V5V
5V
3.3V
3.3V
DATE:
SHEET OF
TITLE: SCHEMATIC
APPROVALS
PCB DES.
APP ENG.
SIZE:
SCHEMATIC NO. AND REVISION:
CUSTOMER NOTICE
THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES AND
SUPPLIED FOR USE WITH ANALOG DEVICES PARTS.
SKU NO.
IC NO.
ANALOG DEVICES HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED
SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S
RESPONSIBILITY TO VERIFY PROPER AND RELIABLE
OPERATION IN THE ACTUAL APPLICATION. COMPONENT
SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT
MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE
OR RELIABILITY. CONTACT ANALOG DEVICES
APPLICATIONS ENGINEERING FOR ASSISTANCE.
2555 AUGUSTINE DRIVE
www.analog.com
ANALOG
DEVICES
AHEAD OF WHAT'S POSSIBLE TM
SANTA CLARA, CA 95054
11
KIM T.
ANDY M.
LTC5597IDC
100MHz - 70 GHz RMS POWER DETECTOR
DC3128A-1 710-DC3128A_REV01
N/A Friday, June 05, 2020DATE:
SHEET OF
TITLE: SCHEMATIC
APPROVALS
PCB DES.
APP ENG.
SIZE:
SCHEMATIC NO. AND REVISION:
CUSTOMER NOTICE
THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES AND
SUPPLIED FOR USE WITH ANALOG DEVICES PARTS.
SKU NO.
IC NO.
ANALOG DEVICES HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED
SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S
RESPONSIBILITY TO VERIFY PROPER AND RELIABLE
OPERATION IN THE ACTUAL APPLICATION. COMPONENT
SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT
MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE
OR RELIABILITY. CONTACT ANALOG DEVICES
APPLICATIONS ENGINEERING FOR ASSISTANCE.
2555 AUGUSTINE DRIVE
www.analog.com
ANALOG
DEVICES
AHEAD OF WHAT'S POSSIBLE TM
SANTA CLARA, CA 95054
11
KIM T.
ANDY M.
LTC5597IDC
100MHz - 70 GHz RMS POWER DETECTOR
DC3128A-1 710-DC3128A_REV01
N/A Friday, June 05, 2020DATE:
SHEET OF
TITLE: SCHEMATIC
APPROVALS
PCB DES.
APP ENG.
SIZE:
SCHEMATIC NO. AND REVISION:
CUSTOMER NOTICE
THIS CIRCUIT IS PROPRIETARY TO ANALOG DEVICES AND
SUPPLIED FOR USE WITH ANALOG DEVICES PARTS.
SKU NO.
IC NO.
ANALOG DEVICES HAS MADE A BEST EFFORT TO DESIGN A
CIRCUIT THAT MEETS CUSTOMER-SUPPLIED
SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S
RESPONSIBILITY TO VERIFY PROPER AND RELIABLE
OPERATION IN THE ACTUAL APPLICATION. COMPONENT
SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT
MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE
OR RELIABILITY. CONTACT ANALOG DEVICES
APPLICATIONS ENGINEERING FOR ASSISTANCE.
2555 AUGUSTINE DRIVE
www.analog.com
ANALOG
DEVICES
AHEAD OF WHAT'S POSSIBLE TM
SANTA CLARA, CA 95054
11
KIM T.
ANDY M.
LTC5597IDC
100MHz - 70 GHz RMS POWER DETECTOR
DC3128A-1 710-DC3128A_REV01
N/A Friday, June 05, 2020
C4
1uF
10V
J2
1
2
3
4
5
6
7
8
9
10
C11
0.1uF
J5
ANALOG IN
1
2
3
4
5
6
J1
JACK
DC-70GHz
C14
0.01uF
C1
0.1uF
C13
10uF
X1
R9
4.99k
C15
0.1uF
J6
TE-282836-2
TERM. BLOCK
1
2
E1
3.3V
R12
100
R10
4.99k
E3
GND
E2
GND
JP1
HD1X2-079
E4
EN
U3
24LC025-I/ST
SDA 5
VCC 8
A0
1
A1
2
A2
3
VSS
4
WP 7
SCL 6
R2
1
J3
DIGITAL
1
2
3
4
5
6
7
8
PCB1 PCB, DC3128A REV01
R1
2k
R13
3k
R11
4.99k
U1
LTC5597
VCC
1
OUT
2
FLTR
3
GND
4GND 5
RFin 6
GND 7
EN 8
GND
9
C10
OPT
U2
LT1761-S5-3.3
GND
2
BYP 4
IN
1VOUT 5
SHDN
3
E5
VOUT
X2
R8
OPT
C12
10uF
JP2
HD1X2-079
R14
OPT
X3
C3
0.01uF
J4
POWER
1
2
3
4
5
6
7
8
C8
10pF
EN
SCL
SDA
EGND
AREF
A0
6
DEMO MANUAL DC3129A-KIT
Rev. 0
ANALOG DEVICES, INC. 2020
12/20
www.analog.com
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and
conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation
Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)
and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to
Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and
agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted
is expressly made subject to the following additional limitations:Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board;and (ii) permit any Third
Party to access the Evaluation Board. As used herein, the term “Third Party”includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is
NOT sold to Customer;all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all
be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of
use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile
or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited
to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS
Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF
LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS”AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY
DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS
LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING
BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE
HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States
federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts
(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits
to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
Indice
Altri manuali Analog Devices Hardware per computer
Analog Devices
Analog Devices ADSP-21000 Guida utente
Analog Devices
Analog Devices EZ-Board ADSP-21489 Manuale utente
Analog Devices
Analog Devices VisualDSP++ 5.0 Manuale utente
Analog Devices
Analog Devices ADF7021-V Manuale utente
Analog Devices
Analog Devices LTC2949 Manuale utente
Analog Devices
Analog Devices Blackfin Manuale utente
Analog Devices
Analog Devices EVAL-ADN4650EB1Z Manuale utente
Analog Devices
Analog Devices DC3089A Manuale utente
Analog Devices
Analog Devices SHARC ADSP-2136 Series Guida all'applicazione
Analog Devices
Analog Devices MicroConverter ADuC832 Manuale utente
Analog Devices
Analog Devices Linear LT3383 Guida rapida alla configurazione
Analog Devices
Analog Devices DC2745A Guida rapida alla configurazione
Analog Devices
Analog Devices MICROCONVERTER ADUC812 Manuale utente
Analog Devices
Analog Devices HPUSB Manuale utente
Analog Devices
Analog Devices EVAL-ADPD6000 Manuale utente
Analog Devices
Analog Devices Linear ADP5070 Guida rapida alla configurazione
Analog Devices
Analog Devices SHARC ADSP-21065L Manuale utente
Analog Devices
Analog Devices HSC-ADC-EVALA-SC Manuale utente
Analog Devices
Analog Devices ADV7604 Manuale utente
Analog Devices
Analog Devices EVAL-ADF4152HVEB1Z Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
