Anolis ArcPad 48 Integral Manuale utente
1
User instructions
ArcPad 48
The product generates colored light by means of Luxeon LEDs.The product was designed for exterior use
and it is ideal for locations where the effect lighting is required.
1.Attention:
During the operation the housing becomes hot (up to 85°C)
Do not install the module near high inammable liquids or materials
Do not allow anything to rest on the module
Do not install the module near the naked ames
The unit is not suitable for underwater installation
Do not install the module in dirty,dusty or badly ventilated location
Avoid using the unit in locations subject to possible impacts.
Avoid looking directly into the LED light beam at close range.
2.Installation
The ArcPad 48 unit can be arranged in any position orientation.The ArcPad´s head is mounted on an adjustable
bracket for “tilt” adjustment into many positions.
To x the unit.
1. Loosen both pan screws (1) in the xture base.
2. Turn the internal adjustable holder (2) to the position
as shown on the picture and take it out from the base.
3. Fasten the internal holder on the non-ammable surface
via 2 mounting holes of diameter of 9.2 mm.
4. Put the base of the xture on the internal holder (2) ,adjust
its desired pan position and tighten both pan screws (1). Adjust suitable
tilt position.
The ArcPpad 3•48 should be connected to the ArcPower 48 driver. See the ArcPower 48 user manual for full
2
details of mains power requirements and DMX operation.
Connect the ArcPad 48 ´s cable to the ArcPower 48 via the adapter cable Chogori/RJ45. The power/data cable
that connect the ArcPad 48 to the ArcPower48 has the following wiring:
Adapter cable Chogori/ RJ45 betwen xture and LED driver
3.Technical specications:
Maximum Power Consumption: 60 W
Comp. Power Supply for RGBW version: ArcPower 48
Comp. Power Supply for single colour and
SW version: ArcPower 48 SmartWhite
Operating Ambient Temp.Range: -20°C/+40°C
Cooling System: convection
Led device: Luxeon Rebel
Number of LEDs 48
Optical System: 25° lens-array
Typical Lumen Maintenance: 70%@ 60,000 hours
Led Life Expectancy: minimum 60,000 hours
Operating Temperature: +70°C@ambient 25°C
Ingress Protection: IP 67
Construction:
Body: cast aluminium
Base: cast aluminium
Transparent cover: tempered glass
"tilt" range: +60°/-90°
"pan" range: +45°/-45°
Power /Data Connection plug: Chogori 08BMMA-SL8001 (male)
Power /Data Connection cable: Belden Cable 7930A Paired-Pata Tuff Cat. 5e,AWG 24
LED Colour Variants *: RGBW, CW, WW, SW
3
4.Dimensions:
(All dimensions are in mm)
5. Accessories
1 x Connector Chogori CGRBDU-08BFFA (female)
6. Optional Accessories
Adapter cable CGRBDU-08BFFA/RJ4 RJ45, L=3m (No. 13051630)
Adapter cable CGRBDU-08BFFA/RJ4 RJ45, L=7m (No. 13051631)
Adapter cable CGRBDU-08BFFA/RJ4 RJ45, L=15m (No. 13051682)
Specications are subject to change without notice.
Altri manuali per ArcPad 48 Integral
1
Indice
Altri manuali Anolis Attrezzatura di illuminazione
Anolis
Anolis ArcPower 36 Manuale utente
Anolis
Anolis ArcSource 96 Integral Manuale utente
Anolis
Anolis ArcPad 48 Integral/W Manuale utente
Anolis
Anolis ArcSource Outdoor 24 MC Integral SmartWhite Manuale utente
Anolis
Anolis ArcSource Outdoor 48 MC Manuale utente
Anolis
Anolis ArcPower 48 Outdoor /W Manuale utente
Anolis
Anolis ArcPower 144 Manuale utente
Anolis
Anolis ArcSource Submersible II Manuale utente
Anolis
Anolis ArcPar S1 Manuale utente
Anolis
Anolis Robin MiniMe Manuale utente
