AT&T 2402 Manuale utente

REVISED

5/7/02

Expansion Handset 2402

Fold open this manual for information

about this product’s installation

and operation. Please also

read Part 1 — Important

Product Information.

AT&T and the Globe Design are

trademarks of AT&T Corp. licensed to

Advanced American Telephones.

Printed in China. Issue 2AT&T 05/02

Visit us at www.telephones.ATT.com

AT&T and the Globe Symbol are trademarks of AT&T Corp. licensed to Advanced American Telephones.

USER’S MANUAL

Part 2

2402_map_2ATT 5/7/02 6:32 PM Page 6

BEFORE YOU BEGIN

About Handset Registration

• You must register this (and any other) handset with the base,

following the directions in “REGISTER THE HANDSET.” This handset is

compatible with telephone model 2462.

• The original handset that came with the base is automatically

registered as Handset 1.

• Additional handsets will be assigned Handset 2, Handset 3, Handset 4,

Handset 5, Handset 6, Handset 7, and Handset 8.

• Whenever you install a handset battery pack, the handset will display

SEARCHING FOR BASE (if it’s registered) or ENTER BASE ID (if it’s

not registered).

About Softkeys

• The handset softkeys are located below the screen display.

• Press the softkey below the operation displayed on the screen to

select that operation. (For example, to enter the menu, press the

center softkey).

• Press O(CLEAR) at any time to return to the previous screen.

• Press and hold O(CLEAR) to return to the idle screen.

Softkeys

Screen

display of

operations to

be selected

with softkeys.

2402_map_2ATT 5/7/02 6:32 PM Page 1

CHARGE THE BATTERY

1 Install the handset battery pack.

Use only the battery supplied with this handset or AT&T Accessory

Battery Model 2401, SKU#91077.

• When you install the battery pack the first time, the handset will

display ENTER BASE ID.

2 Charge the handset battery.

• Place the handset in the remote charging stand (purchased

separately). The CHARGING light goes on.

• Charge the battery at least 12 hours. After the first charge,

the battery typically charges in only eight hours.

b) Place the battery pack in

the handset. Match the

metal contacts on the

battery with the contacts

in the battery

compartment.

c) Replace cover

by sliding it on

its track up

over battery

case until it

snaps firmly

into place.

a) Remove

battery

compartment

cover by

pressing on

indentation

and sliding

downward.

2402_map_2ATT 5/7/02 6:32 PM Page 2

1Make sure to charge the handset battery pack at least 12 hours.

2At the 2462 corded base, press .

3Use or to select DISPLAY BASE-ID.

4Press . The base screen will display the 15-digit Base ID code

for about 30 seconds, then return to the idle screen. Write down the

Base ID code so you can enter it at the handset in STEP 6 below.

5At the cordless handset, use the softkey to select REGISTER.

6Enter the 15-digit Base ID code.

7Use the softkey to select OK. The screen displays PLEASE WAIT!!.

8After about 45 seconds, the screen displays FOUND BASE. If the

handset displays BASE BUSY TRY LATER, the base is in use.

For complete operation instructions,

refer to the manual that came with

your original handset.

2402_map_2ATT 5/7/02 6:32 PM Page 3

INSTALLATION

Belt Clip

Attach the belt clip (optional).

Headset

You can use this telephone

hands-free when you install

any industry standard

2.5 mm headset (purchased

separately). For best results,

use an AT&T 2.5 mm

headset.

Plug the headset into the

jack located on the left side

of the handset (under the

small rubber flap). Do not

force the connection, but

make sure the plug fits

securely.

a) Slide down into

grooves to attach.

b) To remove, lift one side

with your thumbnail

and push back.

2402_map_2ATT 5/7/02 6:32 PM Page 4

Battery Life

Battery life depends on how far the handset is from the base, and other

environmental conditions.

NOTE: For optimum performance, charge your cordless handset in

the handset charger every night.

Charge the Handset Battery Pack

• This battery should remain charged for up to five days. A fully charged

battery provides an average talk time of about six to eight hours.

• The battery pack needs charging when:

– The battery icon ( ) flashes,

– A warning tone sounds, or

– The screen displays LOW BATTERY when idle.

• Place the handset in the handset charger so the CHARGING light

goes on. The battery pack is typically charged in eight hours. For best

results, the initial charge should be twelve hours.

• You can keep the battery fully charged by returning the handset to

the handset charger after each use.

• If you repeatedly get a Low Battery indicator, even after eight hours of

charging, the battery should be replaced. Use only AT&T Accessory

Battery Model 2401, SKU# 91077.

CAUTION: Charge the battery provided with or identified for use

with this product only in accordance with the instructions and

limitations specified in the User’s Manual, Part 1.

2402_map_2ATT 5/7/02 6:32 PM Page 5

Indice

Manuali Cornetta popolari di altre marche

Swissvoice

Swissvoice ePure HD Manuale utente

Philips

Philips TD6736/BH051P Manuale utente

ASCOM

ASCOM I62 - Manuale utente

LG-Ericsson

LG-Ericsson LIP-9010 Manuale utente

GE 1583 Manuale utente

iiNet

iiNet Handset Manuale utente

ASCOM

ASCOM 9p23 Manuale utente

AirCell

AirCell ST 3100 Manuale utente

Eaton

Eaton HHIR-LCD-PROG Istruzioni per il montaggio

Mitel

Mitel 112 Manuale utente

SBC

SBC SBC-381H Manuale utente

Mitel

Mitel 5602 Manuale utente

ASCOM

ASCOM d81 Messenger Istruzioni per l'installazione

SpectraLink

SpectraLink 7522 Manuale utente

Avaya

Avaya L100 Series Come usare

ooma

ooma HD2 Handset Manuale utente

Yealink

Yealink IPW56 Manuale utente

Sony

Sony SBH52 Manuale utente