Atdec VFS-DH Manuale utente
VFS-DH Page 1 of 4
Installation Guide
VFS-DH
Freestanding Dual Horizontal
REQUIRED TOOLS
• Phillips Head Screwdriver
A
Crossbar
(x1)
B
VESA
Plate
(x2)
C
Upright
Pole
(x1)
D
Base
(x1) K
(Optional)
Security Screw
(x2)
L
Cable Ball
(x6)
E
3/5mm
Allen Key
(x1 each)
F
M8x50mm
Screw (x1)
G
M6x25mm
Cap Screw
(x1)
H
Mounting
Screw
M4x16mm
(x8)
I
Mounting
Screw
M4x12mm
(x8)
J
Mounting
Screw
M4x10mm
(x8)
M
Cable Clip
(x4)
COMPONENT CHECKLIST
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! EachVFSDisplayHeadsupportsamaximumweightasperaboveweightrangespecication.
! ThisproductsupportsVESAmountingholecongurations:75x75mmand100x100mm.
! Themanufactureracceptsnoresponsibilityforincorrectinstallation.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and
offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may
bewithinthestatedrange.PleasecontactAtdecifyouwouldlikefurtherinformation.
WEIGHT RANGE
Per Monitor
Flat Monitor
0-12kg(0-26.5lb)
Curved Monitor
0-9kg(0-20lb)
NOTE
• 120mm (4.75”) max overall
monitor depth.
• 2kg(4.4lb)maximumweight
differencebetweenmonitors.
VFS-DH Page 2 of 4
1. Attach Upright Pole to Base
1.1 Attach the upright pole
to the base as shown below.
Ensure the cable slot faces
towards the rear. Cable Slot
USER
BACK
TIGHTEN
FIRMLY
Upright Pole
M8x50mm Screw
5mm Allen Key
3. Attach the VESA plate to your monitor (Repeat steps 3 to 6 for each monitor)
NOTE: Be sure to select a screw
length that suits the monitor.
3.1 Check VESA mounting compatibility 3.2 Screw VESA plate to back of
monitor using provided screws.
100mm
75mm
100mm 75mm
Top of
monitor
Too short Too long
OK
2. Attach crossbar and display heads
2.1 Attach crossbar to pole. 2.2 Slide display heads onto crossbar.
OPEN
1
SLIDE
DISPLAY
HEAD
ONTO
CROSSBAR
2
REPLACE
END CAP
3
CLOSE DISPLAY HEAD LEVER ONCE
IN PLACE ON CROSSBAR.
4
HOLD SUPPORT IN PLACE
TIGHTEN
M6x25mm Cap Screw
5mm
Allen Key
CLAMP
Cable slot to
face back
OPTIONAL
BOLT THROUGH &
GROMMET MOUNT
Mount can also be bolted
to work surface or via
grommet hole with the
Atdec Grommet Clamp
(AC-GC),soldseparately.
VFS-DH Page 3 of 4
4. Attach your display to the VFS display head
4.1 Hook the top of the VESA plate onto
the display head.
! While mounting the first monitor,
carefully support mount to prevent
tipping.
4.2 Press and hold the two buttons on
the display head. Gently push bottom of
VESA plate into display head. Release
buttons to lock in place.
4.3 (Optional) Insert the security
screw, and tighten using a phillips-head
Screwdriver.
5. Adjust horizontal position of the monitor
5.1 Open the lever to loosen
the display head.
5.2 Slide the display head to
desired position.
Note: support monitor
weight to aid sliding.
5.3 If necessary, adjust the
tension between the display
head and the pole using the
5mm allen key supplied.
5.4 Close the lever to lock the
display head in place.
HOOK
Back of
Display
OPEN
LOOSEN
TIGHTEN
SLIDE
CLOSE
Release
Button
PUSH
TIGHTEN
Security
Screw
6. Adjust the ball joint tension 7. Cable Management
6.1 If the monitors are not holding position or are
stiff to move, adjust the tension plate by tightening
or loosening the three screws.
+-
Note: Adjust 3
screws evenly in
small increments
Note: Support the monitor while making adjustments.
3mm
Allen Key
7.1 Connect cables to your monitors. Then route them
down to the table by inserting them into the cable slots
in the crossbar and upright pole. Use either the cable
balls or cable clips to secure them in place as shown.
Leave slack
in cables
Cable
Balls (x6)
Cable
Clips
Leave slack
in cables
Cable
Balls (x6)
Cable
Clips
Note Ensure enough slack is left in cables
to allow for movement. When the slot in
each pole cannot be used, use the supplied
cable clips to secure the display cables.
VFS-DH Page 4 of 4
8.1 Remove monitors
8.3 Remove crossbar from pole
8.5 Lock display head onto pole
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20201207
OPTIONAL 8. Switch to a single monitor mount
Preview
8.2 Slide display head off crossbar
8.4 Slide display head onto pole
UNLOCK
REMOVE
END CAP SLIDE DISPLAY HEAD
OFF CROSSBAR
3
1
2
Slot
UNLOCK
SLIDE DISPLAY
HEAD ONTO POLE
(Ensure tongue in
display head aligns
with slot in pole)
Tongue
3
2
REMOVE
POLE CAP 1
3
PRESS AND
HOLD BUTTONS
LIFT OFF MONITOR
PULL OUT BOTTOM
OF MONITOR
2
1
SUPPORT
CROSSBAR
UN-SCREW
CROSSBAR
(Use 5mm
Allen Key)
REMOVE
CROSSBAR
FROM POLE
2
1
3
REPLACE
POLE CAP
LOCK DISPLAY HEAD
TO POLE
Re-attach monitor
following steps 4.1 to 4.3
2
1
Altri manuali Atdec Rack e supporto
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec AD-WFP-5040 Manuale utente
Atdec
Atdec AWM-A13-B Manuale utente
Atdec
Atdec AV Cart 75 Manuale utente
Atdec
Atdec AWMS-2-BT75 Manuale utente
Atdec
Atdec AWMS-DW Manuale utente
Atdec
Atdec ADBS-4x1-39TW Foglio di istruzioni
Atdec
Atdec AWMS-2-LTH75-H Manuale utente
Atdec
Atdec TELEHOOK 12/30 Multi Manuale utente
Atdec
Atdec Levitate L-PB Manuale utente
Atdec
Atdec APA-B Manuale utente
Atdec
Atdec TH-1026-VF Manuale utente
Atdec
Atdec Telehook Manuale utente
Atdec
Atdec AWMS-2-BT75-G Manuale utente
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec Spacedec SD-POS-VBM-B2B Manuale utente
Atdec
Atdec AWM-A13 Manuale utente
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec AWMS-2-4640-C Manuale utente
Atdec
Atdec AD-TVAC-CM Manuale utente
