Atdec AF-AT Manuale utente
AF-AT Page 1 of 4
COMPONENT CHECKLIST
B
Monitor
arm
(x1)
C
Pole Assembly
(x1)
A
VESA
head
(x1)
D
Rotation
limiter
(x1)
I
Screw
M8 x 30mm
(x1)
N
Pole
top cap
(x1)
O
Bolt through
base
(x1)
P
5mm
Allen key
(x1)
Q
Mounting
screws
M4 x 10mm
(x4)
R
Mounting
screws
M4 x 12mm
(x4)
S
Mounting
screws
M4 x 16mm
(x4)
J
Security Screw
M4 x 16mm
(x1)
K
Steel
washer
(x1)
L
Cable
stop
(x2)
M
Cable
clip
(x1)
E
Primary arm
cable cover
(x1)
F
Secondary arm
cable cover
(x1)
G
Desk clamp
assembly
(x1)
H
Screw
M8 x 60mm
(x1)
Installation Guide
AF-AT
Single Arm
Desktop Monitor Mount
REQUIRED TOOLS
WEIGHT RANGE
• Phillips Head Screwdriver
Flat Monitors
0 - 8kg
(0 - 17.6lbs)
Curved Monitors
0 - 5.5kg
(0 - 12lbs)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with the range of AF Poles and arms.
! The manufacturer accepts no responsibility for incorrect installation.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the
capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further
information.
AF-AT Page 2 of 4
1. Desk overview
The desk clamp bracket
can be repositioned to
suit different mounting
surface thicknesses.
2. How to reconfigure desk clamp
2.1 Remove screws
(M8 x 16mm Countersunk screw)
2.2 Remove clamp plate 2.3 Invert bracket 2.4 Replace clamp plate 2.5 Reattach bracket
Pressure Plate
M10 Desk Clamp Screw
5mm Allen Key
M8 x 30mm
Countersunk
screw Tighten
firmly
3.2 Place in desired location 3.3 Screw pressure plates in and tighten firmly.3.1 Attach clamp to post
3. Post mount configuration
Default Inverted
MIN THICKNESS - 0mm (0”)
MAX THICKNESS - 39mm (1.5”)
MIN THICKNESS - 35mm (1.4”)
MAX THICKNESS - 76mm (3”)
52mm
(2.1”)
55mm
(2.2”)
88mm
(3.5”)
140mm
(5.5”)
Desk Clamp
4. Bolt through - Drill Hole
9mm
(3/8”)
25mm
offset
5. Bolt Pole to work surface
Note orientation of
plate with pole
5mm
Allen Key
M8x60mm
Screw
Bolt
Through
Plate
4.1 Drill 9mm hole in
desired post position
on work surface.
AF-AT Page 3 of 4
Arm Assembly
6. Install VESA monitor head
7. Install arm assembly
Handgrip Tab
5mm
Allen Key
Pole
Top Cap
VESA monitor
head
Screen
M4x10/12/16mm
Phillips Head Mounting
Screws
6.1 Install VESA monitor head as shown.
7.1 Unlock handgrip and raise so
that handgrip tab protrudes
7.4 Slide the Arm Assembly and
Handgrip down the pole before locking
the handgrip at the desired height
7.5 Insert Pole Top
Cap into Pole. This is
also where the Allen
Key is stored.
7.3 Slip the Arm Assembly
over the Handgrip Tab and
then onto the Pole
7.2 OPTIONAL ROTATION LIMITER
Insert rotation limiter for 180�
rotation around mounting pole
100mm
75mm
100mm 75mm
8. Mounting Monitor
VESA monitor head
Arm Assembly
8.2 OPTIONAL SECURITY SCREW
Ensure the Monitor is supported, then loosen the Monitor head
screw with the 5mm Allen Key and tilt screen up before installing
the M4 x 16mm Security Screw into the Security Screw hole
Note: Support Screen
when adjusting tilt.
8.1 Insert VESA monitor head into
the receptacle in the Arm Assembly
5mm Allen Key
Phillips Head
Screwdriver
Loosen
Tighten
Security Screw
Hole
M4 x 16mm
Security Screw
Monitor head
screw
AF-AT Page 4 of 4
Cable
Stop
Cable
Clip
Note: Ensure enough cable
slack is given to allow for
movement.
Lock Slot
Elbow Joint
‘click’
‘click’
Lock Slot
Elbow Joint
‘click’
‘click’
9.1 Unlock Handgrip ensuring both the
screen and arm assembly are supported
10.1 After plugging in your cables,
install the Cable Covers.
Insert Cable Covers
up into Lock Slots.
10.2 Push Cable Covers away from
Elbow Joint to secure in place.
9.2 Lift/Lower the Screen to the desired
height. Move both Screen and Arm
assembly together
9.3 Lock Handgrip firmly
10.3 Cable Clips and Cable Stops can be installed
to further manage cables.
9. Adjusting Height
10. Cable Management
11. Insert Cable Stops
Note: Press down firmly onto
the other edge of the Cable
Stop and hold. This allows the
rear profile to flex in place
11.1 Insert Cable Stop on one edge
of the Pole Slot
11.2 Insert allen key into top cap
on pole
12. Adjusting the Display Bracket
Allen Key
Storage
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20191024A
Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
No Allen Key
necessary
No Allen Key necessaryNote: Support Screen when
adjusting tilt.
100mm
75mm
100mm 75mm
5mm Allen Key
Tighten
Loosen
VESA 75 x 75 / 100 x 100mm
Altri manuali Atdec Rack e supporto
Atdec
Atdec Visidec VF-AT-NP Manuale utente
Atdec
Atdec TH-3060-UFL Manuale utente
Atdec
Atdec AD-TVAC-CM Manuale utente
Atdec
Atdec AWM-AD Manuale utente
Atdec
Atdec AWM-X40 Manuale utente
Atdec
Atdec VFS-DV Manuale utente
Atdec
Atdec Visidec Focus Articulated Arm Wall Istruzioni operative
Atdec
Atdec AF-M Manuale utente
Atdec
Atdec AD-AC-PH Manuale utente
Atdec
Atdec AWM-BT Manuale utente
Atdec
Atdec SYSTEMA SW6S Manuale utente
Atdec
Atdec AWM-FC Manuale utente
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec AWM-A71 Manuale utente
Atdec
Atdec AWM-A71-B Manuale utente
Atdec
Atdec AD-WFP-5040 Manuale utente
Atdec
Atdec AWM-LR Manuale utente
Atdec
Atdec Visidec Focus Micro Istruzioni operative
Atdec
Atdec SPACEDEC ACROBAT Istruzioni operative
Atdec
Atdec AWMS-DW6 Manuale utente
