Atdec AWM-LR Manuale utente
AWM-LR Page 1 of 4
Installation Guide
AWM-LR
Dual Crossbar
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Do not remove/ throw away the plastic cap on arm links, channel clamp or base.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can
exceed the capacity of the mount even though the monitor weight may be within the stated range.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is compatible with AWM Series monitor arm products.
COMPONENT CHECKLIST
REQUIRED TOOLS
A
Crossbar
Assembly
(x1)
B
VESA Plate
(x2)
C
Handle
(x1)
D
Screw
M4x10mm
(x8)
E
Screw
M4x12mm
(x8)
F
Screw
M4x16mm
(x8)
I
Plastic
Washer
(x2)
H
Hole
Cap
(x2)
J
Screw
M6x16mm
(x2)
G
Security
screw
(x2)
K
4mm
Hex Key
(x1)
L
3mm
Hex Key
(x1)
• Phillips Head Screwdriver
2 - 7kg
(4.5 - 15lbs)
per monitor
WEIGHT RANGE
Monitor weight should be
within the weight range of all
modular elements that make
up the complete monitor
mounting solution.
AWM-LR Page 2 of 4
3. Attach VESA plates to monitors
1. Mount crossbar onto arm
2. (OPTIONAL) Attach handle
1.1. Push crossbar onto shaft at end
of arm. Do not remove plastic cap.
1.3. Tighten joint
screw to secure
rail to arm.
NOTE: Check the crossbar rotation is
smooth after tightening.
1.2. Ensure crossbar is fully pushed
onto shaft.
3.3. Be sure to use a screw length
that suits the monitor.
3.2. Attach VESA head onto monitor
with provided screws.
NOTE: Spacers may be required
for curved, recessed or uneven
monitor surfaces.
100mm
75mm
100mm 75mm
Too short Too long
OK
3.1. Check VESA mounting compatibility.
NOTE: For other sizes, use a suitable
adaptor plate (sold separately).
2.1. Use the 4mm Hex Key to loosely
fasten the handle onto the crossbar.
2.2. Adjust handle to a height that suits
the monitors, then tighten the two screws.
2.3. If not using handle t hole caps.
M6x16
Screw
Plastic
Washer
AWM-LR Page 3 of 4
5. Adjust the ball joint tension
6. Cable Management
4. Mount monitors onto crossbar
5.1. If the monitors are not holding
position or are stiff to move, adjust
the tension plate by tightening or
loosening the three screws.
NOTE: Adjust 3 screws evenly
in small increments
NOTE: Support the monitor
while making adjustments.
+-
3mm
Hex Key
IMPORTANT!
Ensure enough cable slack is given to allow for movement of the monitors.
4.1. Hook the top of the VESA
plate onto the ball joint mount.
4.2. Gently push the bottom of the
monitor until the VESA plate locks
into place.
4.3. (OPTIONAL) Tilt the monitor
upwards to install the security screw.
Tilt Up
Push
Click
Hook
Repeat steps 4.1 to 4.3 for second monitor
AWM-LR Page 4 of 4
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20220920
+/- 5°
Push
Loosen
Tighten
Adjust level of crossbar
8.1. Rotate the
crossbar so that
it sits parallel to
the worksurface.
OPTIONAL: If the crossbar rotation is
too loose or stiff, adjust the tension
screw under the centre of the crossbar.
7.2. Monitors can also be rotated to portrait position.
ANGLEDFLAT
Adjust monitor angle
7.1. Slide the monitors along the crossbar until they
are positioned centrally in the desired position.
Adjust horizontal position of monitors
7. Adjustments
WARNING: If returning display to landscape orientation, ensure the hook is facing upwards.
Altri manuali Atdec Rack e supporto
Atdec
Atdec AWM-WS Manuale utente
Atdec
Atdec Visidec Focus Articulated Arm Wall Istruzioni operative
Atdec
Atdec AWM Series Manuale utente
Atdec
Atdec TH-1026-VF Manuale utente
Atdec
Atdec VFS-Q Manuale utente
Atdec
Atdec AWMS-2-LTH75-H Manuale utente
Atdec
Atdec AWM-W6 Manuale utente
Atdec
Atdec AD-WM-7060 Manuale utente
Atdec
Atdec AWM-BT Manuale utente
Atdec
Atdec AWMS-2-BT75-G Manuale utente
Atdec
Atdec AWM-W35 Manuale utente
Atdec
Atdec AD-TVC-70R Manuale utente
Atdec
Atdec AD-TVC-70A Manuale utente
Atdec
Atdec AWMS-2-BT75-G Manuale utente
Atdec
Atdec AWMS-BT40 Manuale utente
Atdec
Atdec AWM-BT Manuale utente
Atdec
Atdec AWMS-BT40 Manuale utente
Atdec
Atdec TH-2050-VFM Manuale utente
Atdec
Atdec Visidec Focus Micro Istruzioni operative
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
