Atdec AWM Series Manuale utente

AWMS-NDB-F Page 1 of 7

Installation Guide

AWMS-NDB

AWM Dynamic Notebook Arm

IMPORTANT INFORMATION

!Please ensure this product is installed as per these installation instructions.

!Do not remove/ throw away the plastic cap on the base.

! This product is compatible with Atdec AWM Series products.

! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed

the capacity of the mount even though the monitor weight may be within the stated range.

! The manufacturer accepts no responsibility for incorrect installation.

CONTENTS

F Clamp

Page 2

Base

Page 3

Dynamic Arm

Page 4

AWM Notebook Tray

Page 4

AWM-FF

Component Checklist + Clamp Installation

AWM-LB

Component Checklist + Base Installation

AWM-AD

Component Checklist + Arm Installation

AWM-HN

Component Checklist + Tray Installation

COMPONENT CHECKLIST

AWM-AD

Dynamic

Arm

(x1)

AWM-HN

AWM

Notebook Tray

(x1)

AWM-FF

F Clamp

(x1)

AWM-LB

Base

(x1)

• Phillips Head

Screwdriver

REQUIRED TOOLS

AWMS-NDB-F Page 2 of 7

AWM-FF

F Clamp

COMPONENT CHECKLIST

5mm Allen key

(x1)

Lower Clamp

(x1)

Upper Clamp

(x1)

Screw M8 x 16mm

(x2)

1. Attach base to upper clamp

Fasteners

supplied

with base

2. Attach lower clamp to upper clamp

2.1 Measure the worksurface thickness and

choose the suitable lower clamp position

2.3 Attach lower clamp to upper

clamp in the suitable position

using the two provided screws.

(Normal position shown here)

2.2 If using inverted

position change the

screw direction of

the lower clamp

A B

A - Normal

0 - 36mm

(0.00 - 1 ”)

B - Inverted

36 - 79mm

(1 ”- 3”)Note: If there is only a small gap

behind the worksurface, perform

Step 3.1 before this step.

3. Fit xing to work surface

3.1 Place in desired location on worksurface 3.2 Screw in pressure plate and tighten rmly.

5mm

allen key

Mounting

surface

AWMS-NDB-F Page 3 of 7

AWM-LB

Base

COMPONENT CHECKLIST

2. Set arm rotation to 180° (optional)

Note: default arm rotation is set to rotate 360°

2.1 Remove plastic sleeve. 2.2 To remove rotation ring press down

on front edge and lift.

2.3 Replace rotation ring in the desired

orientation and replace plastic sleeve.

360°

Default Position

Flipped Position

180°

360°

Default Position

Flipped Position

180°

360°

Default Position

Flipped Position

180°

3. Fit arm onto Base

3.1 Push arm onto base, grub screw must

be backed off at this time.

3.2 Ensure arm is fully pushed onto base. 3.3 Tighten set screw.

NOTE: Check

the arm pan

adjustment is

smooth after

tightening.

NOTE: Ensure plastic

sleeve is on shaft

before tting arm.

1. Attach Base to Fixing

C Clamp

Bolt

Through

Kit

AC-GC

Grommet

Clamp

HD F Clamp

F Clamp

1.1 Follow the F Clamp

installation guide

on pages 2 of this

booklet or provided

with your alternate

xing option.

C Clamp

Bolt

Through

Kit

AC-GC

Grommet

Clamp

HD F Clamp

F Clamp

Heavy Duty

F Clamp

AWM-FH

Also Compatible

Bolt Through

Kit

AWM-FB

C Clamp

Bolt

Through

Kit

AC-GC

Grommet

Clamp

HD F Clamp

F Clamp

C Clamp

Bolt

Through

Kit

AC-GC

Grommet

Clamp

HD F Clamp

F Clamp

Supplied

F Clamp

AWM-FF

C Clamp

AWM-FC

C Clamp

Bolt

Through

Kit

AC-GC

Grommet

Clamp

HD F Clamp

F Clamp

Grommet

Clamp

AC-GC

C Clamp

Bolt

Through

Kit

AC-GC

Grommet

Clamp

HD F Clamp

F Clamp

Screw M8 x 16mm

(x1)

Base

(x1)

Screw M8 x 30mm

(x1)

AWMS-NDB-F Page 4 of 7

COMPONENT CHECKLIST

VESA

head

(x1)

Screw

M4x25mm

(x4)

Security

screw

(x1)

Screw

M4x12mm

(x4)

Spacer

(x4)

Screw

M4x16mm

(x4)

4mm

allen key

(x1)

Display

Arm

(x1)

WEIGHT RANGE

Flat Monitors

0 - 9kg

(0 - 20lbs)

Curved Monitors

0 - 6kg

(0 - 13.5lbs)

Display weight should be

within the weight range

of all modular elements

that make up the complete

display mounting solution.

AWM-AD

Dynamic Arm

COMPONENT CHECKLIST

0 - 8kg

(0 - 18lb)

WEIGHT RANGE

Device weight should be

within the weight range of

all modular elements that

make up the complete display

mounting solution.

Notebook

Tray

(x1)

Hook-and-Loop

Fasteners

(x4)

AWM-HN

AWM Notebook Tray

1. Set arm rotation to 180° (optional)

1.1 Remove plastic sleeve. 1.3 Place rotation ring in the desired position. The

tag on the ring should always face towards the user.

180°

360°

Default

Position

Flipped

Position

1.2 Remove rotation ring.

1. Press

2. Lift

AWMS-NDB-F Page 5 of 7

3. Mount Notebook Tray onto arm

3.3 Push the lever down

to secure it to the arm

assembly.

3.2 Ensure that the Notebook Tray is seated

fully into the receptacle at the end of the

display arm. There should be no gap.

3.1 Insert Notebook Tray into

the display arm

Gap No gap

Note: Ensure the lever is

unlocked when tting.

4. Mount notebook computer

4.1 Adjust the support tabs to

suit the width of the notebook

computer ensuring that cable

ports are not obstructed.

4.2 To increase stability, use the

self adhesive Hook-and-Loop

Fasteners supplied.

a. Peel off the backing paper to

the fasteners.

b. Attach fasteners to both the

Notebook Tray and notebook

computer.

c. Ensure that each set of

fasteners are correctly aligned

i.e. Hook to Loop.

5. Adjust tilt tension & install security screw

5.1 Use the allen key to adjust the tilt tension until the tray

holds in a vertical position at the end of the arm.

Note: Support

tray while

adjusting.

5.2 (Optional) Tilt the head upwards to install the optional

security screw.

2. Fit arm onto Base

2.1 Push arm onto shaft. 2.2 Ensure arm is fully pushed onto shaft. 2.3 Tighten joint screw.

Note: Check the

arm rotation is

smooth after

tightening.

Tighten

Loosen

Tighten

Loosen

AWMS-NDB-F Page 6 of 7

Heavier

Monitor

Lighter

Monitor

6. Adjust arm tension

6.1 To accurately set the tension of the arm, position

the device at 90 degrees

6.2 Use the allen key to adjust the arm tension to the weight of

the device. Follow steps 6.3 to 6.5 to set the tension.

6.3 If the device sags or falls down,

increase the arm tension by rotating

the screw clockwise.

6.5 If the device oats or hovers

in all positions the arm tension

is balanced and does not require

further adjustment.

6.4 If the device springs upwards from the

bottom position, decrease the arm tension

by rotating the screw anti-clockwise.

Device Falls

(from top)

Increase Tension

Device ‘Floats’

(all positions)

Balanced

Device Springs

(from bottom)

Reduce Tension

7. Tension gauge

7.1 When

installing multiple

devices of a

similar weight,

use the tension

gauge to make

installation faster.

1. Set up one device and record the

position of the marker on the

gauge.

2. When installing subsequent

displays, pre-tension the arm

to the recorded amount, then

ne-tune the tension by following

steps 6.3 to 6.5.

Arm Tension Gauge

Marker

8. Cable management

8.1 Plug cables into the device and

route the cables down the arm using

the cable hooks and clips.

8.2 Wedge cable into the central gap

and slide it down the arm.

8.3 The cable should slip into the arm

cavity

8.4 Slide the remaining loose cable

from the central gap up the arm.

See steps 8.2 to 8.4

Important!

Ensure enough cable slack is

given in this area to allow for

movement of the device.

90°

AWMS-NDB-F Page 7 of 7

9. Adjust Notebook Tray

9.1 Pan tray to desired position. 9.2 Position and align notebook with other monitors.

+/- 5°

Levelling

Adjustment

8.5 Cable clips and covers

can be used to further

manage cables.

Note: After

connecting the

notebook computer

cables, route them

through the cable

management clip

on the back of the

Notebook Tray.

Note: Ensure enough

cable slack is given to

allow for movement.

LIFT

10.2 Attach VESA head onto display with

provided screws.

You may choose to convert your solution to mount a display, to do so:

100mm

75mm

100mm

75mm

Flush

Too long Too short

Spacer

5mm 12mm

10.3 Be sure to use correct screw

length

10.1 VESA mounting compatibility

100mm

75mm

100mm

75mm

Flush

Too long Too short

Spacer

5mm 12mm

Note: For other sizes, use a suitable

adaptor plate (sold separately).

Note:

Spacers may

be required

for curved,

recessed

or uneven

display

surfaces.

Display arm

10.5 Ensure that the VESA head sits ush

within the display arm. There should be no

gap.

10.4 Insert VESA head into the display arm 10.6 Push the lever down to

secure it to the arm assembly

Gap No Gap

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Atdec Rack e supporto

Atdec

Atdec AWM-P G Manuale utente

Atdec

Atdec AWMS-2-BT75-H Manuale utente

Atdec

Atdec AD-TVAC-CM Manuale utente

Atdec

Atdec TELEHOOK 12/30 Multi Manuale utente

Atdec

Atdec AWM-P G Manuale utente

Atdec

Atdec AWM-LR Manuale utente

Atdec

Atdec AD-WM-7060 Manuale utente

Atdec

Atdec AWM-LR Manuale utente

Atdec

Atdec AWMS-3-137140-C Manuale utente

Atdec

Atdec AWMS-DW6 Manuale utente

Atdec

Atdec AWM-W6 Manuale utente

Atdec

Atdec AF-AA Manuale utente

Atdec

Atdec SYSTEMA SW6S Manuale utente

Atdec

Atdec AWM 460 Arm Manuale utente

Atdec

Atdec AWMS-2-LTH75-H Manuale utente

Atdec

Atdec Spacedec Acrobat Swing Arm Double Manuale utente

Atdec

Atdec AWMS-2-D13-C Manuale utente

Atdec

Atdec AWMS-2-BT75-FS Manuale utente

Atdec

Atdec AWM-A13 Manuale utente

Atdec

Atdec VISIDEC FOCUS MICRO Istruzioni operative

Atdec

Atdec AWMS-2-BT75-G Manuale utente

Atdec

Atdec AWMS-2-BT75-FS Manuale utente

Atdec

Atdec TH-PFK Manuale utente

Atdec

Atdec AF-ATC Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente