Atdec AF-ATC Manuale utente
AF-ATC Page 1 of 4
COMPONENT CHECKLIST
B
Monitor
arm
(x1)
C
Pole Assembly
(x1)
H
Rotation
limitor
(x1)
I
Screw
M8 x 30mm
(x1)
O
Pole
top cap
(x1)
K
Bolt through
plate
(x1)
P
5mm
Allen key
(x1)
Q
Mounting
screws
M4 x 10mm
(x4)
R
Mounting
screws
M4 x 12mm
(x4)
S
Mounting
screws
M4 x 16mm
(x4)
T
Security Screw
M4 x 16mm
(x1)
L
Steel
washer
(x1)
M
Cable
stop
(x2)
N
Cable
clip
(x1)
F
Primary arm
cable cover
(x1)
G
Secondary arm
cable cover
(x1)
J
Screw
M8 x 60mm
(x1)
A
VESA
head
(x1)
D
Desk Clamp
(x1)
E
Pressure
Plate
(x1)
Installation Guide
AF-ATC
Single Arm
Desktop Monitor Mount - C Clamp
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with the range of AF Poles and arms.
! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
WEIGHT RANGE
• Power Drill
• Drill Bit
• Phillips Head Screwdriver
0 - 8kg
(0 - 17.6lbs)
AF-ATC Page 2 of 4
1. Desk overview
1.1 Worksurface thickness
2.2 Place in desired location 2.3 Screw pressure plates in and tighten rmly.
2.1 Attach clamp to post
2. Post mount configuration
5. Install VESA monitor head
VESA monitor
head
Screen
M4x10/12/16mm
Phillips Head Mounting
Screws
5.1 Install VESA monitor head as shown. 100mm
75mm
100mm 75mm
Pressure Plate
Clamp Screw
Allen Key
MIN THICKNESS - 10mm (3/8”) MAX THICKNESS - 34mm (1,1/4”)
3. Bolt through - Drill Hole
9mm
(3/8”)
25mm
offset
4. Bolt Pole to work surface
Note orientation of
plate with pole
5mm
Allen Key
M8x60mm
Screw
Bolt
Through
Plate
Steel
Washer
3.1 Drill 9mm hole in
desired post position
on work surface.
M8 x 30mm
screw Tighten
rmly
Place pressure
plate on end of
clamp screw
AF-ATC Page 3 of 4
Arm Assembly
6. Install arm assembly
Handgrip Tab
5mm
Allen Key
Pole
Top Cap
6.1 Unlock handgrip and raise so
that handgrip tab protrudes
6.4 Slide the Arm Assembly and
Handgrip down the pole before locking
the handgrip at the desired height
6.5 Insert Pole Top
Cap into Pole. This is
also where the Allen
Key is stored.
6.3 Slip the Arm Assembly
over the Handgrip Tab and
then onto the Pole
6.2 OPTIONAL ROTATION LIMITER
Insert rotation limiter for 180�
rotation around mounting pole
7. Mounting Monitor
VESA monitor head
Arm Assembly
7.2 OPTIONAL SECURITY SCREW
Ensure the Monitor is supported, then loosen the Monitor head
screw with the 5mm Allen Key and tilt screen up before installing
the M4 x 16mm Security Screw into the Security Screw hole
Note: Support Screen
when adjusting tilt.
7.1 Insert VESA monitor head into the
receptacle in the Arm Assembly
5mm Allen Key
Phillips Head
Screwdriver
Loosen
Tighten
Security Screw
Hole
M4 x 16mm
Security Screw
Monitor head
screw
8.1 Unlock Handgrip ensuring both the
screen and arm assembly are supported
8.2 Lift/Lower the Screen to the desired
height. Move both Screen and Arm
assembly together
8.3 Lock Handgrip rmly
8. Adjusting Height
AF-ATC Page 4 of 4
Cable
Stop
Cable
Clip
Note: Ensure enough cable
slack is given to allow for
movement.
Lock Slot
Elbow Joint
‘click’
‘click’
Lock Slot
Elbow Joint
‘click’
‘click’
9.1 After plugging in your cables,
install the Cable Covers.
Insert Cable Covers
up into Lock Slots.
9.2 Push Cable Covers away from
Elbow Joint to secure in place.
9.3 Cable Clips and Cable Stops can be installed
to further manage cables.
9. Cable Management
10. Insert Cable Stops
Note: Press down rmly onto
the other edge of the Cable
Stop and hold. This allows the
rear prole to ex in place
10.1 Insert Cable Stop on one edge
of the Pole Slot
10.2 Insert allen key into top cap
on pole
11. Adjusting the Display Bracket
Allen Key
Storage
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180723
Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
No Allen Key
necessary No Allen Key necessary
Note: Support Screen
when adjusting tilt.
100mm
75mm
100mm 75mm
5mm
Allen Key
Tighten
Loosen
VESA 75 x 75 / 100 x 100mm
Altri manuali Atdec Rack e supporto
Atdec
Atdec AWMS-46W35 Manuale utente
Atdec
Atdec TH-3060-UFL Manuale utente
Atdec
Atdec AWM-BT Manuale utente
Atdec
Atdec AWM-W6 Manuale utente
Atdec
Atdec TELEHOOK 12/30 Multi Manuale utente
Atdec
Atdec AWMS-3-137140-C Manuale utente
Atdec
Atdec AWM-LC Manuale utente
Atdec
Atdec ADBS-2x2-17MFB Manuale utente
Atdec
Atdec A F -AT-W Manuale utente
Atdec
Atdec Visidec Freestanding Double Manuale utente
Atdec
Atdec ADBS-4x1-39TW Foglio di istruzioni
Atdec
Atdec AWMS-2-BT75 Manuale utente
Atdec
Atdec TH-PFK Manuale utente
Atdec
Atdec APA-B Manuale utente
Atdec
Atdec VISIDEC FOCUS MICRO Istruzioni operative
Atdec
Atdec AWM-HS Manuale utente
Atdec
Atdec AF-AT-NBC Manuale utente
Atdec
Atdec AWM-X40 Manuale utente
Atdec
Atdec AF-M Manuale utente
Atdec
Atdec AWM-W35 Manuale utente
