Atdec AWM-X40 Manuale utente
AWM-X40 Page 1 of 3
Installation Guide
AWM-X40
AWM Stack Kit 40
COMPONENT CHECKLIST
REQUIRED TOOLS
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is only compatible with Atdec AWM Post 40 Stackable (AWM-P40X).
! Both posts must be AWM-P40X when using this kit.
! The manufacturer accepts no responsibility for incorrect installation.
• 10mm (3/8”) Wrench
• 8mm (5/16”) Wrench
(unstacking only)
A
M6 Threaded Rod
with M8 Tips
(x2)
B
M6 Washer
Plate
(x1)
C
M6 Split
Washer
(x2)
D
M6 Nut
(x2)
AWM-X40 Page 2 of 3
remove label
but ensure
alignment
insert stays
in place.
Alignment
insert
Ensure channels
without guide
marks are aligned
on both posts.
Alignment
insert
Alignment
insert
If alignment insert falls out,
reposition it as shown above.
Ensure arrow on alignment
insert points away from the
post channel without guide
marks on both posts.
1. Screw Threaded Rods into Post
2. Stack Post
1.1 Remove post cap and label on both posts.
NOTE
Rods can be
nger tightened
2.1 Align the second post with
its alignment insert facing the
tips of the rods. Then feed the
threaded rod into the holes of
the second post.
2.2 Slide the post down the rods until it sits
ush against the top of the lower post.
1.2 Screw threaded rods into the end of one
post that has the alignment insert.
IMPORTANT Check Desk Fixing (xing sold separately)
AWM-FH AC-GC
Atdec Custom
Rail Plate
When stacking posts only the following
heavy duty xings can be used:
i
!
1.1 If lower post is already installed, the
xing on the lower post may need to be
changed. Follow the installation guide
provided with your heavy duty xing
to attach it to the post and t it to the
worksurface.
NOTE:
Posts can be stacked
before or after attaching
to desk xing.
STACKING INSTRUCTIONS
AWM-X40 Page 3 of 3
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20201030
Remove two
threaded rods
using an 8mm
(5/16”) wrench.
If tips come off the
end of the rods
screw them back
together before
storing for later use.
Unscrew two nuts
using 10mm (3/8”)
wrench.
Ensure the two
alignment inserts
stay in the ends
of both posts.
1. Remove Stacked Post
2. Remove Threaded rods
UNSTACKING INSTRUCTIONS
1.1 Remove cap and all monitor
arms from the stacked post.
2.1 Unscrew two threaded rods using
an 8mm (5/16”) wrench.
1.2 Remove nuts and washers
from top of post.
2.2 Fit post cap
1.3 Slide stacked post up off the
threaded rods.
2.3 Store parts together for later use.
Tighten two nuts
firmly using 10mm
(3/8”) wrench.
Ensure the post join area
remains well aligned
while tightening the nuts.
3. Fasten Posts Together
3.1 Screw together the posts using
the provided nuts and washers.
3.2 Fit post cap
Follow post and
arm installation
guides to complete
installation of your
mounting solution.
Installation Complete
Altri manuali Atdec Rack e supporto
Atdec
Atdec VFS-DV Manuale utente
Atdec
Atdec AWM-LTH Manuale utente
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec AWM-A13 Manuale utente
Atdec
Atdec TH-1026-VF Manuale utente
Atdec
Atdec APA-B Manuale utente
Atdec
Atdec Visidec Focus Micro Manuale utente
Atdec
Atdec TH-PFK Manuale utente
Atdec
Atdec TH-3060-UF Manuale utente
Atdec
Atdec AF-ATC Manuale utente
Atdec
Atdec AWM-A46-B Manuale utente
Atdec
Atdec AWMS-BT40 Manuale utente
Atdec
Atdec AWMS-2-D13-C Manuale utente
Atdec
Atdec AWM-P G Manuale utente
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec AWM-A13-B Manuale utente
Atdec
Atdec AWMS-3-137140-C Manuale utente
Atdec
Atdec TH-3060-UFL Manuale utente
Atdec
Atdec TELEHOOK 12/30 Multi Manuale utente
Atdec
Atdec AWM-P G Manuale utente
