Atdec AWM-A46-B Manuale utente

AWM-A46 Page 1 of 4

Installation Guide

AWM-A46

460 Arm

COMPONENT CHECKLIST

REQUIRED TOOLS

Monitor Arm

(x1)

VESA Head

(x1)

Screw

M4x25mm

(x4)

Screw

M4x16mm

(x4)

Screw

M4x12mm

(x4)

Spacer

(x4)

Security

screw

(x1)

4mm

allen key

(x1)

Post Clamp

(x1)

WEIGHT RANGE

• Phillips Head Screwdriver

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! This product is compatible with Atdec AWM Series products.

0 - 12kg

(0 - 26.5lbs)

AWM-A46 Page 2 of 4

3. Place the rotation ring

in the desired postion

2. Set arm rotation to 180° (optional)

2.1 Remove plastic sleeve

from post clamp.

2.2 Remove rotation ring. 2.3 Place rotation ring in

desired position.

Note: rotation ring placement

depends on the position of the clamp

on the post. The tag on the ring

should always face toward the user.

1. Remove plastic sleeve

2. Remove rotation ring

1. Press

2. Lift

Note rotation is set to 360� by default.

180°

360°

Default

Position

Flipped

Position

Tag

1. Fix clamp to Post or Wall Channel

1.1 Ensure knob is undone. 1.2 Slide post clamp into channel.

Push knob to

aid insertion

1.3 Hold clamp in desired position on

channel and turn knob to lock in place.

1. Ensure Knob is undone

Tip: push knob

to aid insertion

2. Slide post clamp into channel

3. Hold clamp in desired position on post and turn

knob to lock in place

3. Fit arm onto post clamp

Note: Check the

arm rotation is

smooth after

tightening.

3.1 Push arm onto shaft. 3.2 Ensure arm is fully pushed onto shaft. 3.3 Tighten joint screw.

1. Push arm onto clamp

2. Ensure arm is fully pushed onto clamp

3. Tighten set screw

Tip: Check the

arm rotation is

smooth after

tightening.

AWM-A46 Page 3 of 4

Tighten

Loosen

Tighten

Loosen

5. Mount monitor

Monitor arm

5.1 Insert VESA head into the monitor arm 5.3 Push the lever down to secure

it to the arm assembly

5.2 Ensure that the VESA head sits flush within

the monitor arm. There should be no gap

Gap No gap

6. Adjust tilt tension & Install security screw

6.1 Use the allen key to adjust the tilt tension until the monitor

holds in a vertical position at the end of the arm.

Note: Support

monitor while

adjusting.

6.2 OPTIONAL security screw

To install the optional security screw tilt the head upwards

4. Attach VESA head to monitor

100mm

75mm

100mm 75mm

Flush

Too long Too short

Spacer

5mm 12mm

4.2 Screw the VESA head onto monitor

Note spacers may be required for curved,

recessed or uneven monitor surfaces.

4.3 Ensure the correct screw length is used

to attach the monitor.

4.1 VESA mounting compatibility

100mm

75mm

100mm 75mm

Flush

Too long Too short

Spacer

5mm 12mm

Note: For other sizes, use a suitable

adaptor plate (sold separately).

AWM-A46 Page 4 of 4

atdec.com | atdec.co.uk | atdec.com.au

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

Note: The cable cover shown

does not come with all posts

7.4 To reposition the cable cover, pull it

straight up and out of the post and insert

it into any of the available channels

Cable cover

Cable

Cover

Desk

Clamp

7.1 Push the cable down into the cable clip

Note: Cable clips do not

come with all posts

7.6 Feed remaining cable into cover

7.5 Loop cable and insert into cable cover

7.2 Push cable clip into post channel

7. Post cable management

7.3 Recommended post cable cover

position for double or triple arm set-ups

Note

Ensure enough cable

slack is given to allow for

movement of the monitor

Push

6. Monitor arm cable management

6.1 Plug cables into the monitor and route

the cables down the arm using the cable

hooks and clips

Alternative cable

cover positions

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Atdec Rack e supporto

Atdec

Atdec AWMS-BT40 Manuale utente

Atdec

Atdec AD-TVAC-CM Manuale utente

Atdec

Atdec TELEHOOK TH-3060-UT Manuale utente

Atdec

Atdec AWMS-2-D13-C Manuale utente

Atdec

Atdec 8060 Manuale utente

Atdec

Atdec AWM-LR Manuale utente

Atdec

Atdec Levitate L-PB Manuale utente

Atdec

Atdec AWM-A71 Manuale utente

Atdec

Atdec AF-MC Manuale utente

Atdec

Atdec AWM-W35 Manuale utente

Atdec

Atdec AWMS-2-BT75-FS Manuale utente

Atdec

Atdec AWMS-DW6 Manuale utente

Atdec

Atdec AWM 460 Arm Manuale utente

Atdec

Atdec AD-WFP-5040 Manuale utente

Atdec

Atdec AWM-X40 Manuale utente

Atdec

Atdec TH-3060-UFL Manuale utente

Atdec

Atdec VFS-DH Manuale utente

Atdec

Atdec AWMS-2-BT75 Manuale utente

Atdec

Atdec AF-AN Manuale utente

Atdec

Atdec AWM-HS Manuale utente

Atdec

Atdec AD-WM-7060 Manuale utente

Atdec

Atdec TH-PFK Manuale utente

Atdec

Atdec AWM-W35 Manuale utente

Atdec

Atdec AWM 710 Arm Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente