Atdec AF-M Manuale utente
AF-M Page 1 of 4
H
Cable Clip
(x1)
I
Pole
Top Cap
(x1)
J
Bolt Through
Base
(x1)
K
2mm
Allen key
(x1)
L
5mm
Allen key
(x1)
P
Security Screw
M4 x 16mm
(x1)
M
Mounting
screws
M4 x 10mm
(x4)
N
Mounting
screws
M4 x 12mm
(x4)
O
Mounting
screws
M4 x 16mm
(x4)
C
Desk clamp
assembly
(x1)
D
Screw
M8 x 60mm
(x1)
E
Screw
M8 x 30mm
(x1)
F
Steel
Washer
(x1)
G
Cable
Stops
(x2)
B
Pole
Assembly
(x1)
A
VESA
head
(x1)
Installation Guide
AF-M
Micro Desktop Monitor Mount
COMPONENT CHECKLIST
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with the range of AF Poles and arms.
! The manufacturer accepts no responsibility for incorrect installation.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the
capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further
information.
REQUIRED TOOLS
WEIGHT RANGE
• Phillips Head Screwdriver
Flat Monitors
0 - 8kg
(0 - 17.6lbs)
Curved Monitors
0 - 5.5kg
(0 - 12lbs)
AF-M Page 2 of 4
1. Desk overview
The desk clamp bracket
can be repositioned to
suit different mounting
surface thicknesses.
2. How to reconfigure desk clamp
2.1 Remove screws
(M8 x 16mm Countersunk screw)
2.2 Remove clamp plate 2.3 Invert bracket 2.4 Replace clamp plate 2.5 Reattach bracket
Pressure Plate
M10 Desk Clamp Screw
5mm Allen Key
M8 x 30mm
Countersunk
screw Tighten
firmly
3.2 Place in desired location 3.3 Screw pressure plates in and tighten firmly.3.1 Attach clamp to post
3. Post mount configuration
Default Inverted
MIN THICKNESS - 0mm (0”)
MAX THICKNESS - 39mm (1.5”)
MIN THICKNESS - 35mm (1.4”)
MAX THICKNESS - 76mm (3”)
52mm
(2.1”)
55mm
(2.2”)
88mm
(3.5”)
140mm
(5.5”)
Desk Clamp
4. Bolt through - Drill Hole
9mm
(3/8”)
25mm
offset
5. Bolt Pole to work surface
Note orientation of
plate with pole
5mm
Allen Key
M8x60mm
Screw
Bolt
Through
Plate
Steel
Washer
4.1 Drill 9mm hole in
desired post position
on work surface.
AF-M Page 3 of 4
100mm
100mm
6. Install VESA monitor head
VESA monitor
head
Screen
M4x10/12/16mm
Phillips Head Mounting
Screws
6.1 Install VESA monitor head as shown.
7. Mounting Monitor
8. Unlock/Lock Arm Rotation (Note: Focus Micro comes assembled in the “Locked” Position.)
Pole
2mm Allen Key
Grub ScrewMicro Arm
2mm Allen Key
Grub Screw
C
L
Grub Screw Hole
Slot in Pole
VESA monitor head
Arm Assembly
7.2 OPTIONAL SECURITY SCREW
Ensure the Monitor is supported, then loosen the Monitor head
screw with the 5mm Allen Key and tilt screen up before installing
the M4 x 16mm Security Screw into the Security Screw hole
Note: Support Screen
when adjusting tilt.
7.1 Insert VESA monitor head into the
receptacle in the Arm Assembly
Unlock
If you wish your Focus Micro Arm to have 360º rotation
about the Pole you will need to unlock the arm’s rotation
Step 1: Unlock the arm by turning the Grub Screw
anti-clockwise removing the Grub Screw completely
Note: Store the Grub Screw in a safe place if you are to
return the arm to the Locked position
Lock
If you have unlocked your Focus Micro Arm, but wish to
fix rotation around the Pole, you will need to lock the arm
Step 1: Ensure the hole for the Grub Screw in the Micro
Arm is lined up with the centre of the Slot in the Pole
Step 2: Re-insert the Grub Screw
previously removed. Turn the Grub
Screw clockwise until it is tight.
Do not over-tighten
5mm Allen Key
Phillips Head
Screwdriver
Loosen
Tighten
Security Screw
Hole
M4 x 16mm
Security Screw
Monitor head
screw
AF-M Page 4 of 4
9.1 Unlock Handgrip ensuring both
screen and arm assembly are supported
9.2 Lift/Lower Screen to the desired
height. Move both Screen and Arm
assembly together.
9.3 Lock Handgrip firmly.
9. Adjusting Height
Note: If Focus Micro
is to be used in a multi
user environment, use
the supplied Cable Clip
to secure the display’s
cables to the Pole.
Cable Stop
Cable Clip
Note: Ensure enough
cable slack is given to
allow for movement.
Note: If Focus Micro
is to be used in a multi
user environment, use
the supplied Cable Clip
to secure the display’s
cables to the Pole.
Cable Stop
Cable Clip
Note: Ensure enough
cable slack is given to
allow for movement.
10.2 After connecting cables,
Cable Clips and Cable Stops can
be installed to further manage
cables. Please See Over.
10. Cable Management
11. Insert Cable Stops
Note: Press down firmly onto
the other edge of the Cable
Stop and hold. This allows the
rear profile to flex in place
11.1 Insert Cable Stop on one
edge of the Pole Slot
11.2 Insert allen key into top cap
on pole
12. Adjusting the Display Bracket
Allen Key
Storage
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20191024A
Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
No Allen Key
necessary
No Allen Key necessaryNote: Support Screen when
adjusting tilt.
100mm
100mm
5mm Allen Key
Tighten
Loosen
VESA 75 x 75 / 100 x 100mm
Indice
Altri manuali Atdec Rack e supporto
Atdec
Atdec AWMS-DW6 Manuale utente
Atdec
Atdec ADBS-3x1-30TW Manuale utente
Atdec
Atdec TH-1040-CTS Manuale utente
Atdec
Atdec VISIDEC FOCUS ARTICULATED ARM DOUBLE Istruzioni operative
Atdec
Atdec TH-1026-VF Manuale utente
Atdec
Atdec AD-WM-5060 Manuale utente
Atdec
Atdec APA-B Manuale utente
Atdec
Atdec VFS-Q Manuale utente
Atdec
Atdec Visidec Freestanding Double Manuale utente
Atdec
Atdec AWM-FC Manuale utente
Atdec
Atdec AWMS-2-BT75-FS Manuale utente
Atdec
Atdec TH-3060-UFL Manuale utente
Atdec
Atdec Spacedec SD-POS-VBM-B2B Manuale utente
Atdec
Atdec AWMS-2-LTH75-H Manuale utente
Atdec
Atdec TELEHOOK TH-3060-UT Manuale utente
Atdec
Atdec Levitate L-PB Manuale utente
Atdec
Atdec 8060 Manuale utente
Atdec
Atdec Telehook Manuale utente
Atdec
Atdec ADBS-4x1-39TW Foglio di istruzioni
Atdec
Atdec ADBS-2x1-17TC Manuale utente
