Atdec AWM-A71-B Manuale utente
AWM-A71 Page 1 of 4
Installation Guide
AWM-A71
710 Arm
COMPONENT CHECKLIST
A
Monitor Arm
(x1)
B
VESA Head
(x1)
D
Screw
M4x25mm
(x4)
E
Screw
M4x16mm
(x4)
F
Screw
M4x12mm
(x4)
G
Spacer
(x4)
H
Security
screw
(x1)
I
4mm
allen key
(x1)
C
Post Clamp
(x1)
REQUIRED TOOLS
WEIGHT RANGE
• Phillips Head Screwdriver
Flat Monitors
0 - 9kg
(0 - 20lbs)
Curved Monitors
0 - 8kg
(0 - 17.6lbs)
Monitor weight should be within the
weight range of all modular elements
that make up the complete monitor
mounting solution.
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! This product is compatible with Atdec AWM Series products.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the
capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further
information.
AWM-A71 Page 2 of 4
3. Place the rotation ring
in the desired postion
2. Set arm rotation to 180° (optional)
2.1 Remove plastic sleeve
from post clamp.
2.2 Remove rotation ring. 2.3 Place rotation ring in
desired position.
Note: rotation ring placement
depends on the position of the clamp
on the post. The tag on the ring
should always face toward the user.
1. Remove plastic sleeve
2. Remove rotation ring
1. Press
2. Lift
Note rotation is set to 360� by default.
180°
360°
OR
Default
Position
Flipped
Position
Tag
1. Fix clamp to Post or Wall Channel
1.1 Ensure knob is undone. 1.2 Slide post clamp into channel.
Push knob to
aid insertion
1.3 Hold clamp in desired position on
channel and turn knob to lock in place.
1. Ensure Knob is undone
Tip: push knob
to aid insertion
2. Slide post clamp into channel
3. Hold clamp in desired position on post and turn
knob to lock in place
3. Fit arm onto post clamp
Note: Check the
arm rotation is
smooth after
tightening.
3.1 Push arm onto shaft. 3.2 Ensure arm is fully pushed onto shaft. 3.3 Tighten joint screw.
1. Push arm onto clamp
2. Ensure arm is fully pushed onto clamp
3. Tighten set screw
Tip: Check the
arm rotation is
smooth after
tightening.
AWM-A71 Page 3 of 4
5. Mount monitor
6. Adjust tilt tension & Install security screw
Gap No gap
Monitor arm
5.2 Ensure that the VESA head sits flush within
the monitor arm. There should be no gap.
6.1 Use the allen key to adjust the tilt tension until the monitor
holds in a vertical position at the end of the arm.
Note: Support
monitor while
adjusting.
6.2 OPTIONAL security screw
To install the optional security screw tilt the head upwards
Tighten
Loosen
Tighten
Loosen
5.1 Insert VESA head into the monitor arm 5.3 Push the lever down to
secure monitor to the arm
assembly
4. Attach VESA head to monitor
100mm
75mm
100mm 75mm
Flush
Too long Too short
Spacer
5mm 12mm
4.2 Screw the VESA head onto monitor
Note spacers may be required for curved,
recessed or uneven monitor surfaces.
4.3 Ensure the correct screw length is used
to attach the monitor.
4.1 VESA mounting compatibility
100mm
75mm
100mm 75mm
Flush
Too long Too short
Spacer
5mm 12mm
Note: For other sizes, use a suitable
adaptor plate (sold separately).
AWM-A71 Page 4 of 4
7. Monitor arm cable management
Note: The cable cover shown
does not come with all posts
8.4 To reposition the cable cover, pull it
straight up and out of the post and insert
it into any of the available channels
Cable cover
Cable
Cover
Desk
Clamp
8.1 Push the cable down into the cable clip
Note: Cable clips do not
come with all posts
8.6 Feed remaining cable into cover8.5 Loop cable and insert into cable cover
8.2 Push cable clip into post channel
8. Post cable management
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20191024A
8.3 Recommended post cable cover
position for double or triple arm set-ups
7.1 Plug cables into the
monitor and route the
cables down the arm
using the cable hooks
and clips.
1
1
2
Important:
Ensure enough cable slack is given
to allow for movement of the monitor
Alternative cable
cover positions
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Atdec Rack e supporto
Atdec
Atdec TELEHOOK 12/30 Multi Manuale utente
Atdec
Atdec Visidec Focus Micro Istruzioni operative
Atdec
Atdec AWM-LR Manuale utente
Atdec
Atdec AWMS-DW Manuale utente
Atdec
Atdec AF Series Manuale utente
Atdec
Atdec TH-1040-CTS Manuale utente
Atdec
Atdec Telehook Manuale utente
Atdec
Atdec Freestanding Quad Manuale utente
Atdec
Atdec AWM-A71 Manuale utente
Atdec
Atdec AWMS-DW6 Manuale utente
Atdec
Atdec AWM-AD Manuale utente
Atdec
Atdec AWM-W35 Manuale utente
Atdec
Atdec AWMS-2-BT75-H Manuale utente
Atdec
Atdec AWM-A13 Manuale utente
Atdec
Atdec SYSTEMA SW6S Manuale utente
Atdec
Atdec AD-WM-5060 Manuale utente
Atdec
Atdec AWM-X40 Manuale utente
Atdec
Atdec AWM-A46-B Manuale utente
Atdec
Atdec AD-TVC-45 Manuale utente
Atdec
Atdec AWMS-46W35 Manuale utente
