ATI Technologies 2H Manuale utente

IQ/OQ

Installation / Operation

Qualification MANUAL

for the

2H and 2H-N

Aerosol Photometers

Air Techniques International

Division of Hamilton Associates, Inc

11403 Cronridge Drive

Owings Mills, MD 21117 USA

TEL: 410 363-9696

FAX: 410 363-9695

www.atitest.com

[email protected]

IQ/OQ 2H, 2H-N Revision 0

Revision A

This page intentionally left blank

Revision A

Table of Contents

1INSTALLATION QUALIFICATION 6

1.1 Requirements 6

1.2 Unpacking 6

2SETUP 7

2.1 Locations & Functions 7

2.2 Front Panel Controls and Indicators 8

2.3 Scanning Probe connections 8

2.4 Rear Panel Connections 9

2.5 Side Connection 10

3OPERATIONAL QUALIFICATION 11

3.1 Initialization 11

3.2 Setup Parameters 11

3.3 Changing Setup Parameters 12

3.4 Setting Up the Alarm Functions 17

3.5 Changing the Reference 17

3.6 UPSTREAM AEROSOL Measurements (DOP or PAO) 18

3.7 Measuring % Leakage - User Defined Reference (USER) 18

3.8 Testing with the 2H 19

3.9 Verifying the Upsream Concentration During Test 19

4MAINTENANCE 20

4.1 Weekly 20

4.2 Annually 20

4.3 General Maintenance procedures 20

4.4 Recommended Spare Parts 20

4.5 Cleaning the TDA-2SP Scanning Probe Screens 21

4.6 Replacing the Main Power Fuses 21

Revision A

4.7 Replacing the HEPA Exhaust Filter 21

A-1. SPECIFICATIONS 22

A-2. TROUBLESHOOTING 23

A-3. QUICK SETUP REFERENCE 24

A-4. RS-232 COMMUNICATION 26

Guidelines to the use of this manual

SYMBOLS

The following symbols are used throughout the manual to draw attention to items or procedures

that require special notice or care.

Operator required action.

Note: Contains important information that, if ignored, can cause inaccurate readings.

Caution: Contains information that, if ignored, can cause equipment damage.

Warning: Contains information that, if ignored, can cause injury or death to those

handling the equipment.

Conventions

[Window] Indicates the information displayed in a window on the Control Panel.

<Function> indicates a button on the Control Panel.

Revision A

1INSTALLATION QUALIFICATION

1.1 REQUIREMENTS

NOTE: High ambient temperatures may create instability in the readings.

The 2H requires the following for proper operation:

•Stable electrical power at 90/240 VAC, single phase, 50/60 Hz, 5 amps.

•Environment Operating Range: 35° to105° Fahrenheit (1.6° to 40.6° Celsius)

with less than 75% relative humidity.

1.2 UNPACKING

NOTE: Save all packaging material for future use.

Carefully unpack and remove the 2H Aerosol Photometer and all accessories from its shipping

container. If the instrument has been damaged in transit, notify the shipper immediately.

Make sure the following items are included with both the 2H (9300133) and the 2HHP (9300134):

1) 1 power cord, 6700001 (120 VAC) or T2E0-0063 (220 VAC)

2) 12 feet of clear PVC tubing, 5200116

3) Operating Manual, 1800110

4) Calibration certificate

The following items are optional. Check the order packing slip.

1) Shipping case, 9300145

2) 2H-SP Scanning Probe, complete, 9300144

a) 1 round isokinetic nozzle (red), T2E0-0572

b) 1 rectangular isokinetic nozzle (blue), T2E0-0798

c) 1 NSF 1” round nozzle (black), T2E0-0005

d) 1 Scanning probe, T2SP-0881

If any of these items are on the order packing slip but missing from the shipment, contact ATI

immediately at: Air Techniques International

Division of Hamilton Associates

11403 Cronridge Drive

Owings Mills, Maryland 21117-2247 U.S.A.

Tel: 410 363-9696 Fax: 410 363-9695

www.atitest.com

Revision A

2SETUP

2.1 LOCATIONS & FUNCTIONS

1 9

3 4 56

Figure 1. Front View

1. Selector Valve. Selects the sample source.

2. Upstream Sample Port. Connects to the sample tubing that is used to measure the upstream

aerosol concentration.

3. Scanning Probe Ground Jack. Electrical ground connection for scanning probe shielding.

(Required for CE compliance)

4. Scanning Probe Connector. Electrical connection for the optional Scanning Probe.

NOTE: Connect the Scanning Probe before applying power to the 2H. Failure to do so

will result in the lack of operation of Scanning Probe’s display. If this occurs, simply

turn off the power to the unit and restart the system.

5. Downstream Sample Port. Connects to the sample tubing or optional Scanning Probe that is

used to measure the downstream sample.

6. Optics indicator light. Corresponds to the cleanliness of the optics.

Green Light Less than 10,000mg* of aerosol

has moved through the

scattering chamber.

Orange Light More than 10,000mg* but less

Revision A

than 17,000mg* of aerosol has

moved through the scattering

chamber.

Red Light More than 17,000mg* of aerosol

has moved through the

scattering chamber. Servicing of

the unit is highly recommended.

* Note: These values are approximate. Actual mass may vary with different airflow rates and

aerosols.

7. Flow indicator light. Displays green when flow is within 5% of 1 CFM, yellow when flow is

from 5% to 10% of 1 CFM, and red when flow is more than 10% above or below 1 CFM.

8. Function Keys. Used for setting operating parameters and initiating program routines

9. Bar Graph Display. Displays an analog representation of the % leakage to aid in isolating

leaks.

10. Front Panel Display. Indicates % leakage readings and error messages.

2.2 FRONT PANEL CONTROLS AND INDICATORS

The front panel contains seven pressure-activated function keys. The <0>, <100>, <REF>, and

<ALARM> keys each contain a red LED to indicate the state of the switch or to prompt the

operator. The <Δ> and <∇> keys are used to scroll among selections as they are shown on the %

LEAKAGE display. The <ENTER> key serves as the command key for sending information to

the processor and for initiating or stopping system routines. The <Δ>, <∇>, and <ENTER> keys

contain no indicator LED.

The % LEAKAGE display is an array of high-visibility LEDs that forms a display screen. The

Front Panel Display shows alphanumeric messages. Below it is a Bar Graph Display that gives a

visual indication of internal photometer cycling or an analog representation of quantity or

percentage.

The Scanning Probe contains an unlabeled display on the pistol grip that is a half-scale duplicate

of the % LEAKAGE Indicator. The two displays are driven by the same electronics and will

always read exactly the same.

The Selector Valve, the Scanning Probe connector, and the two barbed fittings are discussed later.

2.3 SCANNING PROBE CONNECTIONS

If using the 2H with the Scanning Probe, connect the probe’s electrical connector to the 12-pin

connector on the front panel of the 2H before applying power to the photometer. Otherwise, the

display on the Scanning Probe will not function. Connect the probe’s sampling hose to the barbed

DOWNSTREAM fitting to the right of the 12-pin connector. The cable and sampling hose are

Revision A

bound as a single, flexible umbilical. Select the appropriate probe nozzle and screw it onto the

threaded end of the flexible portion of the Scanning Probe.

Note: When using the TDA-2SP Scanning Probe with the 2H, the probe must be

connected to the photometer before the power is turned on. Otherwise the 2H will not

detect the probe and no display will be observed on the pistol grip. If this occurs, switch

the power off, verify that the probe is connected properly, and then switch the power back

on.

2.4 REAR PANEL CONNECTIONS

2 4

1 56

Figure 2. Rear Panel

1. Cooling Fan – Maintains airflow through the unit’s enclosure to stabilize electronics.

2. Power Connector with –Connects to the Power Cord.

3. Fuse Block – Contains 2-amp fuse and spare fuse.

4. Power Switch – Rocker Switch. Turns system power on and off.

5. Serial Number Label – Lists the model and serial number.

6. Vacuum Pump Exhaust – Allows a filter to be installed to eliminate particulate

emissions.

The rear panel contains a recessed, 3-pronged male Power Connector, with an integral fuse block

and power switch, and a Vacuum Pump Exhaust HEPA Filter.

Revision A

CAUTION: The 2H should always be positioned so that the Power Switch, located on

the rear panel, is readily accessible in the event the unit needs to be powered off quickly.

The Power Connector accepts the female end of the Power Cord that comes with the unit. The

internal power supply is a universal supply that can operate at either 50 or 60 Hz and with any

voltage from 90 to 240 volts, for use in virtually all countries. Therefore, any plug with the correct

female end (IEC-320 standard) may be attached to the unit and the universal power supply will

automatically switch to use the supplied input power.

The Vacuum Pump Exhaust HEPA Filter is provided so that the sensitive environments of

cleanrooms can be maintained. The air expelled by the unit is continually filtered of all

particulate matter generated by testing aerosols and the unit using this HEPA exhaust system.

2.5 SIDE CONNECTION

Figure 3. RS-232 Port

RS-232 Port. % Leakage data is continuously sent via the RS-232 port as it is updated on the

Front Panel Display, approximately once per second.

It is recommended that this data be logged to either one of ATI’s data acquisition systems, the

DAS1 or the DAS2. Contact ATI or your local representative to learn more about data logging

options.

If using a terminal program to receive this data, a straight cable must be used (as opposed to a null

modem cable). If using a Pocket PC (PPC) to receive data, the type of cable will depend upon the

brand of PPC. Contact ATI customer service for complete details.

Revision A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ATI Technologies Strumento di misura

ATI Technologies

ATI Technologies Q46UV Manuale utente

ATI Technologies

ATI Technologies 39-0062 Manuale utente

ATI Technologies

ATI Technologies Q46 Series Manuale per l'uso e la cura

ATI Technologies

ATI Technologies Metrinet Manuale utente

ATI Technologies

ATI Technologies Q45S/87 Manuale utente

ATI Technologies

ATI Technologies Q45CT Manuale utente

ATI Technologies

ATI Technologies A15/82 Manuale utente

ATI Technologies

ATI Technologies Scorpion X2 Manuale utente

ATI Technologies

ATI Technologies Q46H/79PR Manuale utente

ATI Technologies

ATI Technologies Q45P Manuale utente

ATI Technologies

ATI Technologies Q46 Series Manuale utente

ATI Technologies

ATI Technologies Q46/88 Manuale utente

ATI Technologies

ATI Technologies 39-0050 Guida

ATI Technologies

ATI Technologies Q46H/65 Manuale utente

ATI Technologies

ATI Technologies Q45D Manuale utente

ATI Technologies

ATI Technologies 2i Manuale utente

ATI Technologies

ATI Technologies Q46P Manuale utente

ATI Technologies

ATI Technologies TDA-110P Manuale

ATI Technologies

ATI Technologies Q45H/62 Manuale utente

ATI Technologies

ATI Technologies Q46 Series Manuale per l'uso e la cura

ATI Technologies

ATI Technologies Q-Blast Q46D Manuale utente

ATI Technologies

ATI Technologies 39-0080 Manuale utente

ATI Technologies

ATI Technologies Q45S/87 Manuale utente

ATI Technologies

ATI Technologies Q-Card Scheda tecnica

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente