Bartec MAK 3003 Manuale utente
MAK 3003_LYNX_V.2.35_KBA 151021
Page 2 of 21
Description of the operating unit
Operating keys
The operating keys have a fixed meaning, e.g. scroll up and down, start and
stop pumping, number keys to enter numeric data etc.
Soft keys
Software controlled keys - depending ontherespective operating state, these
keys are activated by the software and will have different functions assigned
to them - this function is shown beside the soft key on the display, e.g. MENU,
SHUT DOWN etc.
Attention
Some soft keys are “hidden” so that they don’t clog up the screen. To activate
a hidden soft key function, press any soft key on the corresponding side of
the screen and the function will be displayed for 3 seconds - e.g. to activate
the EVENTS screen, press any soft key on the left side of the display the
EVENTS function becomes visible and should be pressed within 3 seconds
or else it will vanish again.
Soft keys
Display
Numerical keys
Operating keys
Selection keys
MAK 3003_LYNX_V.2.35_KBA 151021
Page 3 of 21
Home screen
Start-up screen: you will see this screen when the system starts up or after you have
ended a tour.
The system offers so called hidden functions. To display the hidden panel press any of
the four left soft keys. The EVENTS and LAST TOUR functions become visible. Press the
soft key labeled with the desired function within three seconds to enter it. If you do not
press any soft key the hidden panel will disappear automatically.
Hidden soft keys
Visible soft keys
MAK 3003_LYNX_V.2.35_KBA 151021
Page 4 of 21
Events screen
Here you can see the EVENTS screen with two active alarms. Active alarms are indicated
by an exclamation mark under the “A” column.
The “BC-Reader no connection” alarm is still active, but has been marked as
acknowledged by the user. Please observe that the CONFIRM soft key has vanished once
the alarm has been confirmed. If the problem that caused the alarm is fixed, the
acknowledged alarm will be automatically removed from the EVENTS list.
Confirmed alarms are
indicated by a “Y” (for
Yes) under the “Ac”
column (for
Acknowledged).
MAK 3003_LYNX_V.2.35_KBA 151021
Page 5 of 21
Here you can see that the alarms are not active anymore because the problems causing
them have been fixed. They will be displayed in the EVENTS list until they are confirmed
or the system is restarted.
To leave the EVENTS screen you have to activate the hidden panel by pressing any of the
left soft key first. Press EXIT within 3 seconds to return to the home screen.
Alarms have not
been confirmed yet.
Alarms are not active anymore.
MAK 3003_LYNX_V.2.35_KBA 151021
Page 6 of 21
Start a tour
1. Press the soft key labeled with START TOUR on the home screen
2. The Start Tour screen will appear. Before you can start a tour it is necessary to set
the entries displayed on the screen. You can navigate through the entries with the
selection keys at the bottom left of the operating unit. To set an entry press CHANGE
(or any numeric key). Press CONFIRM to start the tour.
MAK 3003_LYNX_V.2.35_KBA 151021
Page 7 of 21
3. You will also need to enter the expected intake volume of this tour. This is important
for sampling calculations.
You can skip this screen (if you do not want tour sampling) by pressing ABORT.
MAK 3003_LYNX_V.2.35_KBA 151021
Page 8 of 21
Start an intake
1. After starting the tour, the Tour Details screen will appear. This screen has hidden
functions on both sides. It may also show already known intakes at the current
location (GPS). If you have already picked up milk at this location, the system will
remember the supplier id and volume and display it for faster operation.
In the picture above you can also see the Tour Details screen with all hidden functions
displayed (left and right).
2. To start an intake at a new location or if no GPS data is available, you have to
activate the hidden panel by pressing any soft key at the right side. Press INTAKE
within three seconds to initialize a new intake.
MAK 3003_LYNX_V.2.35_KBA 151021
Page 9 of 21
You are presented with the Prepare intake screen. Before you can start the intake you
have to enter the Supplier ID and the Expected Volume.
To set an entry, press CHANGE and type in the value with the numeric keys.
Press ENTER and CONFIRM to start the intake.
MAK 3003_LYNX_V.2.35_KBA 151021
Page 10 of 21
3. To start the intake at an already known (GPS) location, just select the desired entry (if
multiple entries are displayed) and press the green START button the system will
start to suck in the milk.
4. The system waits for milk to be sucked in. You can abort the intake by pressing
ABORT as long as no milk has been detected - once milk has been detected, the
ABORT soft key will disappear.
If you press ABORT, you will return to the Tour Details screen. You can restart the intake
again if needed.
Data from a previous
intake at this (GPS)
location.
Altri manuali per MAK 3003
1
Indice
Altri manuali Bartec Strumento di misura
Bartec
Bartec P-600 Manuale utente
Bartec
Bartec RDW 03 Manuale utente
Bartec
Bartec MAK TIGER 3003 Manuale utente
Bartec
Bartec Tech500 Manuale utente
Bartec
Bartec Tech1000 Manuale utente
Bartec
Bartec Tech200 Manuale utente
Bartec
Bartec VOLUTANK Petro 3003 Manuale utente
Bartec
Bartec ComEx Flex Guida rapida
Bartec
Bartec TECH600PRO Manuale utente
Bartec
Bartec ALCAR TECH600 Manuale utente
Bartec
Bartec QST 250 Manuale utente
Bartec
Bartec 07-662 Series Guida rapida
Bartec
Bartec TECH450PRO Manuale utente
Bartec
Bartec HYGROPHIL H 4230-10 A Series Manuale utente
Bartec
Bartec TECH400 Manuale utente
Bartec
Bartec MR3000DMS Manuale utente
Bartec
Bartec Tech200BT Manuale utente
Bartec
Bartec RLAnet 17-85G5-2123 Series Scheda tecnica
Bartec
Bartec MAK TIGER 3003 Manuale utente
Bartec
Bartec SYSCOM ROCK Manuale utente
