Bin Master DPM-200 Manuale utente

DPM-200 Digital Panel Meter

Instruction Manual

BINMASTER

Division of Garner Industries

7201 North 98th Street, Lincoln, NE 68507 USA

Tel (800) 278-4241 • Fax: (402) 434-9133

www.binmaster.com

•1/8 DIN Digital Panel Meter with NEMA 4X, IP65 Front

•4-20 mA, ± 10 V, TC & RTD Field Selectable Inputs

•Easy Field Scaling in Engineering Units without Applying an Input

•Full 4-Digit Display, 0.56" (14.2 mm) or 1.20" (30.5 mm)

•Shallow Depth Case Extends Only 3.6" (91 mm) Behind Panel

•Isolated 24 VDC @ 200 mA Transmitter Power Supply Option

•2 Relays + Isolated 4-20 mA Output Options

•Free PC-Based MeterView Programming & Monitoring Software

•No Assembly Required

•Sunlight Readable Display

•Operating Temperature Range: -40 to 65°C (-40 to 149°F)

•UL & C-UL Listed. E160849; UL 508 Industrial Control Equipment

•Input Power Options: 85-265 VAC / 90-265 VDC or 12-36 VDC / 12-24 VAC

•Duplex Pump Controller with Alternation Capability

•External Contacts for Remote Button Operation (DPM-200 X2 Only)

•USB, RS-232, & RS-485 Serial Communication Adapters Options

•Modbus RTU Communication Protocol Standard

•Copy Meter Settings to Other DPM-200 Meters

•Password Protection

•Max/Min Display

•High & Low Alarms with Multiple Reset Actions

•3-Year Warranty

DPM-200 Digital Panel Meter Instruction Manual

Disclaimer

The information contained in this document is

subject to change without notice. BinMaster

makes no representations or warranties with

respect to the contents hereof and specifically

disclaims any implied warranties of

merchantability or fitness for a particular purpose.

See Warranty Information and Terms &

Conditions on www.binmaster.com for complete

details.

•Read complete instructions prior to installation

and operation of the meter.

•Risk of electric shock or personal injury.

•This product is not recommended for life support

applications or applications where malfunctioning

could result in personal injury or property loss.

Anyone using this product for such applications

does so at his/her own risk. BinMaster shall not

be held liable for damages resulting from such

improper use.

WARNING

Cancer and Reproductive Harm - www.P65Warnings.ca.gov

Limited Warranty

BinMaster warrants this product against defects

in material or workmanship for the specified

period under “Specifications” from the date of

shipment from the factory. BinMaster’s liability

under this limited warranty shall not exceed the

purchase value, repair, or replacement of the

defective unit. See Warranty Information and

Terms & Conditions on www.binmaster.com for

complete details.

Registered Trademarks

All trademarks mentioned in this document

are the property of their respective owners.

FREE MeterView

Programming Software

Note: The DPM-200 is not powered from USB connection

and requires external power to be programmed.

The easiest and quickest way to program your DPM-

200 is to use the FREE MeterView software.

MeterView software is intuitive, and most customers

can get their meter programmed as they like without

even looking in the manual.

In addition to programming, the software, with

additional devices, may be used for:

•Monitoring up to 100 DPM*200 meters

•Datalogging using your PC

•Generating and saving programming files for

later use

Once your meter is programmed the way you want it,

you can wire it up for your application per the

instructions in this manual and install it. If you find that

you need to make adjustments to the programming

after the meter is installed, you can use the front panel

buttons and the instructions in this manual to do so.

DPM-200 Digital Panel Meter Instruction Manual

Table of Contents

Introduction......................................................................................................... 6

Ordering Information.......................................................................................... 6

Specifications ..................................................................................................... 7

General ............................................................................................................ 7

Process Input .................................................................................................. 7

Temperature Inputs ........................................................................................ 7

Relays Option.................................................................................................. 8

Serial Communications .................................................................................. 8

Isolated 4-20 mA Transmitter Output ............................................................ 8

External Button Contacts (X2 Models Only)................................................. 8

Compliance Information .................................................................................... 9

Safety ............................................................................................................... 9

Electromagnetic Compatibility ...................................................................... 9

Safety Information ........................................................................................ 10

Installation......................................................................................................... 10

Unpacking ..................................................................................................... 10

Panel Mounting ............................................................................................. 10

Mounting Dimensions .................................................................................. 10

Connections .................................................................................................. 11

Connector Labeling ..................................................................................... 11

Power Connections ..................................................................................... 13

Signal Connections ..................................................................................... 13

Relays and 24 V Output Connections ......................................................... 15

Switching Inductive Loads ........................................................................... 15

4-20 mA Output & Input Signal Connections ............................................... 16

External Button Contacts............................................................................. 16

Setup and Programming.................................................................................. 17

Overview........................................................................................................ 17

Front Panel Buttons and Status LED Indicators ........................................ 17

Display Functions and Messages ................................................................... 18

Main Menu ..................................................................................................... 19

Setting Numeric Values................................................................................ 19

Setting Up the Meter (setu).......................................................................... 19

Setting the Input Signal (inpt) .................................................................... 19

Setting the Decimal Point (dc.pt)................................................................. 20

Setting the Temperature Scale (F C)......................................................... 20

Programming the Meter (prog) .................................................................... 20

Scaling the Meter (scal) ............................................................................. 20

Calibrating the Meter (Cal).......................................................................... 21

Recalibrating Temperature Inputs (Cal) ...................................................... 21

Recalibrating Process Inputs (ICal)............................................................ 21

Setting the Relay Operation (rely) ............................................................. 22

Relay and Alarm Operation ......................................................................... 23

Scaling the 4-20 mA Analog Output (Aout) ................................................. 27

Program the Sensor Break Output Value (SEbr)......................................... 27

Analog Output when Display is Out of Range ............................................. 27

Setting Up the Password (pass) .................................................................. 28

Locking the Meter........................................................................................ 28

Unlocking the Meter .................................................................................... 28

Advanced Features Menu ............................................................................ 28

Advanced Features Menu & Display Messages .......................................... 28

Offset Adjustment (Adj)............................................................................... 29

Noise Filter (fltr) ....................................................................................... 29

Noise Filter Bypass (byps) .......................................................................... 29

Serial Communications (serl) .................................................................... 30

Protocol Selection Menu (Prot) .................................................................. 30

DPM-200 Digital Panel Meter Instruction Manual

Select Menu (SElc) ..................................................................................... 30

Linear or Square Root Function (linr or Sqrt) .......................................... 30

Low-Flow Cutoff (cutF) ............................................................................... 30

Display Intensity (inty) ............................................................................... 31

Meter Copy Function (Copy)........................................................................ 31

Meterview Software .......................................................................................... 32

Remote Programming .................................................................................. 32

Data Acquisition ........................................................................................... 32

Monitoring ..................................................................................................... 32

Monitoring System Parts.............................................................................. 32

MeterView Installation .................................................................................. 32

Running MeterView the First Time.................................................................. 32

Enable Meter and Select Meter Address ..................................................... 32

MeterView Main Window .............................................................................. 33

Main Window Menus ................................................................................... 33

Configuration Window.................................................................................. 34

File Menu..................................................................................................... 34

Tools Menu.................................................................................................. 34

Password Menu........................................................................................... 35

Input Tab ..................................................................................................... 35

Set Up Input Type ....................................................................................... 35

Set Up Decimal Point .................................................................................. 35

Set Up Temperature Unit............................................................................. 35

Set Up Temperature Sensor........................................................................ 35

Scaling Tab ................................................................................................. 36

Relays/Alarms Tab ...................................................................................... 36

Advanced Tab ............................................................................................. 36

Info Tab ....................................................................................................... 36

Customize Window....................................................................................... 36

Serial Communication Setup ....................................................................... 37

Relays/Alarms Status ................................................................................... 37

Logging Meter Data to File........................................................................... 37

Log File Sample .......................................................................................... 37

Internal Calibration (ICal) ........................................................................... 38

Operation........................................................................................................... 39

Front Panel Buttons Operation.................................................................... 39

Maximum/Minimum Readings ..................................................................... 39

Troubleshooting ............................................................................................... 40

Diagnostics Menu (diag).............................................................................. 40

Determining Software Version..................................................................... 40

Reset Meter to Factory Defaults .................................................................. 40

Factory Defaults & User Settings ................................................................ 41

Troubleshooting Tips ................................................................................... 42

Quick Interface Reference Guide .................................................................... 43

EU Declaration of Conformity.......................................................................... 45

DPM-200 Digital Panel Meter Instruction Manual

Table of Figures

Figure 1. Panel Cutout and Mounting ................................................................. 10

Figure 2. Meter Dimensions – Side View ............................................................ 10

Figure 3. Case Dimensions – Top View .............................................................. 10

Figure 4. Connector Labeling for PD765-#R0-00-BM......................................... 11

Figure 5. Connector Labeling for PD765-6R0-10-BM......................................... 11

Figure 6. Connector Labeling for PD765-#R2-00-BM......................................... 11

Figure 7. Connector Labeling for PD765-6R2-10-BM......................................... 11

Figure 8. Connector Labeling for PD765-#R3-00-BM......................................... 11

Figure 9. Connector Labeling for PD765-6R3-10-BM......................................... 11

Figure 10. Connector Labeling for PD765-6R3-20-BM....................................... 11

Figure 11. Connector Labeling for PD765-7R5-00-BM....................................... 12

Figure 12. Connector Labeling for PD765-6R5-10-BM....................................... 12

Figure 13. Connector Labeling for PD765-#X0-00-BM....................................... 12

Figure 14. Connector Labeling for PD765-6X0-10-BM....................................... 12

Figure 15. Connector Labeling for PD765-#X2-00-BM....................................... 12

Figure 16. Connector Labeling for PD765-6X2-10-BM....................................... 12

Figure 17. Connector Labeling for PD765-#X3-00-BM....................................... 12

Figure 18. Connector Labeling for PD765-6X3-10-BM....................................... 12

Figure 19. Connector Labeling for PD765-6X3-20-BM....................................... 13

Figure 20. Connector Labeling for PD765-7X5-00-BM....................................... 13

Figure 21. Connector Labeling for PD765-6X5-10-BM....................................... 13

Figure 22. Power Connections ............................................................................ 13

Figure 23. Transmitter Powered by Internal Supply (Optional) ........................ 13

Figure 24. Transmitter Powered by External Supply or Self-Powered............. 13

Figure 25. Voltage Input Connections ................................................................ 13

Figure 26. Thermocouple Input Connections..................................................... 14

Figure 27. Three-Wire RTD Input Connections .................................................. 14

Figure 28. Two-Wire RTD Input Connections..................................................... 14

Figure 29. Four-Wire RTD Input Connections .................................................... 14

Figure 30. Relay & 24 V Output Connections..................................................... 15

Figure 31. AC and DC Loads Protection............................................................. 15

Figure 32. Low Voltage DC Loads Protection .................................................... 15

Figure 33. 4-20 mA Output & Input Signal Powered by Meter .......................... 16

Figure 34. 4-20 mA Output Powered by Meter ................................................... 16

Figure 35. 4-20 mA Output Powered Externally ................................................. 16

Figure 36. DPM-200 X2 Powers Both the Heater and 4-20 mA Input Signal .... 16

Figure 38. Meter Copy Connection ..................................................................... 31

DPM-200 Digital Panel Meter Instruction Manual

Introduction

The DPM-200 digital panel meter is one of the most

versatile digital panel meters on the market and will

satisfy a wide variety of process and temperature

applications. The DPM-200 can be field programmed to

accept process voltage (0-5V, 1-5V, etc) and current

(4-20 mA) inputs, 100 Ohm RTDs, and the four most

common thermocouples types.

One of the DPM-200’s most useful features is its ability

to provide 24 VDC to power the transmitter’s 4-20 mA

signal. This reduces costs and simplifies wiring. The

DPM-200 is housed in a shallow-depth, 1/8 DIN

enclosure that features a NEMA 4X front panel and

convenient mounting hardware. There are two power

options for the DPM-200: 85 to 265 VAC or 12-36 VDC

and certain configurations of the AC powered meter

can provide 24 VDC to power the transmitter, if

needed. Programming and setup can be performed

with the four front panel pushbuttons, free MeterView

software or using the Copy function.

Two relays and isolated 4-20 mA output options

increase the utility of the DPM-200. The relays can be

used for alarm or control applications. The 4-20 mA

output provides an isolated retransmission of the input

signal; especially useful for temperature inputs like

thermocouples and RTDs.

The display height on the standard DPM-200 meter is

0.56" (14.2 mm) and on the DPM-200 X2 the display

height is an astounding 1.2" (30.5 mm). The DPM-200

X2 can be read easily from distances of up to 30 feet!

The intensity of the display on both versions of the

DPM-200 can be adjusted to compensate for various

lighting conditions, especially direct sunlight.

Ordering Information

0.56" Display Models

Model #

Reorder #

Power

Options Installed

PD765-6R0-00-BM 348-0037 85-265 VAC No options

PD765-6R0-10-BM

348-0038

85-265 VAC

24 V transmitter supply

PD765-6R2-00-BM

348-0039

85-265 VAC

2 relays

PD765-6R2-10-BM

348-0040

85-265 VAC

2 relays & 24 V transmitter supply

PD765-6R3-00-BM

348-0041

85-265 VAC

4-20 mA output

PD765-6R3-10-BM

348-0042

85-265 VAC

4-20 mA output & 24 V supply

PD765-6R3-20-BM

348-0043

85-265 VAC

4-20 mA output & dual 24 V supplies

PD765-6R5-10-BM

348-0044

85-265 VAC

2 relays, 4-20 mA output, & 24 V supply

PD765-7R0-00-BM

348-0045

12-36 VDC

No options

PD765-7R2-00-BM

348-0046

12-36 VDC

2 relays

PD765-7R3-00-BM 348-0047 12-36 VDC 4-20 mA output

PD765-7R5-00-BM

348-0048

12-36 VDC

2 relays, 4-20 mA output

1.20" Display Models

Model #

Reorder #

Power

Options Installed

PD765-6X0-00-BM

348-0049

85-265 VAC

No options

PD765-6X0-10-BM

348-0050

85-265 VAC

24 V transmitter supply

PD765-6X2-00-BM

348-0051

85-265 VAC

2 relays

PD765-6X2-10-BM

348-0052

85-265 VAC

2 relays & 24 V transmitter supply

PD765-6X3-00-BM 348-0053 85-265 VAC 4-20 mA output

PD765-6X3-10-BM

348-0054

85-265 VAC

4-20 mA output & 24 V supply

PD765-6X3-20-BM

348-0055

85-265 VAC

4-20 mA output & dual 24 V supplies

PD765-6X5-10-BM

348-0056

85-265 VAC

2 relays, 4-20 mA output, & 24 V supply

PD765-7X0-00-BM

348-0057

12-36 VDC

No options

PD765-7X2-00-BM

348-0058

12-36 VDC

2 relays

PD765-7X3-00-BM

348-0059

12-36 VDC

4-20 mA output

PD765-7X5-00-BM

348-0060

12-36 VDC

2 relays, 4-20 mA output

Manufactured by Precision Digital Corporation, 233 South St, Hopkinton MA 01748 USA

DPM-200 Digital Panel Meter Instruction Manual

Specifications

Except where noted all specifications apply to operation at +25°C.

General

Display

DPM-200: 0.56" (14.2 mm);

DPM-200 X2: 1.20" (30.5 mm) red

LED, 4 digits (-1999 to 9999)

Display

Intensity

Eight user selectable levels. Default

intensity is 6.

Front Panel

NEMA 4X, IP65; panel gasket provided

Programming

Methods

Four front panel buttons, cloning with

Copy feature, PC with MeterView

software, and Modbus registers.

Noise Filter Programmable from 2 to 199

(0 will disable filter)

Display

Update Rate

Process/RTD: 3.7-5/second

Thermocouple: 1.8-2.5/second

Overrange Display flashes 9999

Underrange Display flashes -1999

Recalibration All ranges are calibrated at the factory.

Recalibration is recommended at least

every 12 months.

Max/Min

Display

Stored until reset by user or meter is

turned off.

Password Restricts modification of programmed

settings.

Non-Volatile

Memory

Settings stored for a minimum of 10

years.

Power

Options

85-265 VAC, 50/60 Hz; 90-265 VDC,

20 W max or

12-36 VDC; 12-24 VAC, 6 W max.

Required Fuse

UL Recognized, 5 A max, slow-blow;

up to 6 meters may share one fuse.

Normal Mode

Rejection

64 dB at 50/60 Hz

Isolation

4 kV input/output-to-power line; 500 V

input-to-output or output-to-24 VDC

supplies. -6R5 & -6X5 models only:

100 V output-to-24 VDC supply

Operating

Temperature

-40 to 65°C (-40 to 149°F)

Storage

Temperature

-40 to 85°C (-40 to 185°F)

Relative Humidity

0 to 90% non-condensing

Connections

Power & Signal: removable screw

terminal blocks accept 12 to 22 AWG.

Serial: RJ11 header, standard on all

meters.

Enclosure 1/8 DIN, high impact plastic, UL 94V-0,

color: gray

Tightening

Torque

Screw terminal connectors:

5 lb-in (0.56 Nm)

Weight 9.5 oz. (269 g) (including options)

UL File Number E160849; UL 508 Industrial Control

Equipment

Warranty

3 years parts & labor. See Warranty Infor-

mation and Terms & Conditions on

www.binmaster.com for complete details.

Process Input

Inputs

0-20 mA, 4-20 mA, 1-5 V, ±10 V

Transmitter

Supply

Isolated, one or two transmitter sup-

plies P1: 24 VDC ±10% @ 200 mA

max (-10 option) P1 & P2: 24 VDC

±10% @ 200 mA & 40 mA max

(-20 option)

Accuracy

±0.05% FS ±1 count;

±0.1% FS ±2 counts for square root

Function

Linear or square root

Low-Flow

Cutoff

0 to 9999 (0 disables cutoff function)

Point below at which display always

shows zero.

Decimal Point

Up to 3 decimals.

Calibration

Scale without signal or calibrate with

signal source

Calibration

Range

User programmable over entire range

of meter

Input

Impedance

Voltage range: greater than 1 MΩ,

Current range: 50-100 Ω, varies with

resettable fuse impedance

Input

Overload

Protected by automatically resettable

fuse

Temperature Drift

0 to 65°C

ambient

-40 to 0°C

ambient

Current:±0.20% FS

(50 PPM/°C)

Voltage:±0.02% FS

(1.7 PPM/

Current:

±0.80% FS

Voltage:

±0.06% FS

Temperature Inputs

Inputs

Factory calibrated, field selectable:

type J, K, T, or E thermocouples and

100 Ω platinum RTD (0.00385 or

0.00392 curve)

Resolution 1°; type T TC & RTD: 1° or 0.1°

Cold Junction

Reference

Automatic

Temperature Drift

±2°C maximum

Offset

Adjustment

Programmable to ±19.9°. This parame-

ter allows the user to apply an offset

value to the temperature being

displayed.

Input

Impedance

Greater than 100 kΩ

Accuracy

Input Type

Range

Accuracy

(0 - 65 C)

Accuracy

(-40 - 0 C)

Resolution

J -58 to 1382°F

-50 to 750°C

±2°F

±1°C

±5°F

±3°C

1°

-58 to 2300°F

-50 to 1260

±2°F

±1°C

±4°F

±2°C

1°

-292 to 700

-180 to 371

±2°F

±1°C

±13°F

±7°C

1° or 0.1°

E -58 to 1700ºF

-50 to 927ºC

±2°F

±1°C

±11°F

±6°C

1°

RTD

-328 to 1382°F

-200 to 750

±1°F

±1°C

±5°F

±3°C

1° or 0.1°

DPM-200 Digital Panel Meter Instruction Manual

Relays Option

Rating

2 Form C (SPDT); rated 3 A @ 30 VDC

or 3 A @ 250 VAC resistive load;

1/14 HP (≈ 50 watts) @ 125/250 VAC

for inductive loads such as contactors,

solenoids, etc.

Deadband

0-100% FS, user selectable

Electrical Noise

Suppression

A snubber should be connected to

each relay contact switching inductive

loads to prevent disruption to the

microprocessor’s operation.

Recommended snubber value:

0.01 µF/470 Ω, 250 VAC (PDX6901).

High or Low

Alarm

User may program any alarm for high

or low

Relay

Operation

•Automatic (non-latching) and/or

manual reset

•Latching (requires manual

acknowledge) with/without clear

•Pump alternation control

•Off (disable unused relays)

Relay Reset Front panel button, terminal at back of

meter (X2 models only), or through

serial communications

Time Delay 0 to 199 seconds, on and off delays;

programmable

Sensor Break

Relay Operation

The sensor break relay condition may

be programmed for each relay as

On (alarm) or Off (nonalarm).

The relays will enter these states when

a sensor break is detected for RTD or

thermocouple inputs. These settings

have no effect when current or voltage

inputs are selected.

Fail-Safe

Operation

Programmable, independent for each

relay. Relay coils are energized in

non-alarm condition. In case of power

failure, relays will go to alarm state.

Auto

Initialization

When power is applied to the meter,

relays will reflect the state of the input

to the meter.

Serial Communications

Protocol Modbus RTU

Meter

Address

PDC protocol: 0 - 99

Modbus protocol: 1 - 247

Baud Rate

300 – 19,200 bps

Transmit

Time Delay

Programmable 0 to 199 ms

Data 8 bit (1 start bit, 1 stop bit)

Parity

None (1 or 2 stop bits), even, or odd

(Modbus only; PDC protocol does not

use parity)

Turn Around

Delay

Less than 2 ms (fixed)

Isolated 4-20 mA Transmitter

Output

Scaling Range 1.00 to 23.00 mA; reverse scaling

allowed.

Calibration Factory calibrated for 4-20 mA

Accuracy ±0.1% FS ±0.004 mA

Temperature Drift

50 PPM/°C

Note: Analog output drift is separate

from input drift.

Isolation

500 V input-to-output or output-to-24

VDC supplies; 4 kV output-to-power

line. For -6X5 models only:

100 V output-to-24 VDC supply

External Power 35 VDC maximum

Output Loop

Resistance

Power

supply

Minimum

Maximum

24 VDC 10 Ω700 Ω

35 VDC

(external)

100 Ω1200 Ω

External Button Contacts

(X2 Models Only)

Number

Four

Function Remote operation of front-panel

buttons: programming, reset relays or

view/reset max/min readings.

Open State +5 VDC open contact on button input

terminals

Closed State

Closed contact button input terminal to

common/ground, active low 0 to 0.4 VDC

DPM-200 Digital Panel Meter Instruction Manual

Compliance Information

Safety

Ul Listed USA and Canada

UL 508 Industrial Control Equipment

Ul File Number E160849

Front Panel UL Type 4X, NEMA 4X, IP65; panel

gasket provided

Low Voltage

Directive

EN 61010-1:2010

Safety requirements for measurement,

control, and laboratory use

Electromagnetic Compatibility

Emissions EN 55011:2009 + A1:2010

Group 1 Class A ISM emissions

requirements

Radiated

Emissions

Class A

AC Mains

Conducted

Emissions

Class A

Immunity EN 61326-1:2013

Measurement, control, and laboratory

equipment

EN 61000-6-2:2005

EMC heavy industrial generic immunity

standard

RFI -

Amplitude

Modulated

80 -1000 MHz 10 V/m 80% AM (1 kHz)

1.4 - 2.0 GHz 3 V/m 80% AM (1 kHz)

2.0 - 2.7 GHz 1 V/m 80% AM (1 kHz)

Electrical Fast

Transients

±2kV AC mains, ±1kV other

Electrostatic

Discharge

±4kV contact, ±8kV air

RFI -

Conducted

10V, 0.15-80 MHz, 1kHz 80% AM

AC Surge

±2kV Common, ±1kV Differential

Surge

1KV (CM)

Power-

Frequency

Magnetic Field

30 A/m 70%V for 0.5 period

Voltage Dips 40%V for 5 & 50 periods

70%V for 25 periods

Voltage

Interruptions

<5%V for 250 periods

Note:

Testing was conducted on meters installed through the

covers of grounded metal enclosures with cable shields

grounded at the point of entry representing installations

designed to optimize EMC performance.

DPM-200 Digital Panel Meter Instruction Manual

Safety Information

•Read complete instructions prior to installation

and operation of the meter.

•Risk of electric shock.

•Hazardous voltages exist within enclosure.

•Installation and service should be performed only

by trained service personnel.

Installation

There is no need to remove the meter from its

case to complete the installation, wiring, and

setup of the meter.

Unpacking

Remove the meter from box. Inspect the

packaging and contents for damage. Report

damages, if any, to the carrier.

If any part is missing or the meter malfunctions,

please contact your supplier or the factory for

assistance.

Panel Mounting

•Prepare a standard 1/8 DIN panel cutout – 3.622"

x 1.772" (92 mm x 45 mm). Refer to Mounting

Dimensions for more details.

•Clearance: allow at least 4" (102 mm) behind the

panel for wiring.

•Panel thickness: 0.04" - 0.25" (1.0 mm - 6.4 mm).

Recommended minimum panel thickness to

maintain Type 4X

rating: 0.06" (1.5 mm) steel panel, 0.16" (4.1 mm)

plastic panel.

•Remove the two mounting brackets provided with

the meter (back-off the two screws so that there is

¼" (6.4 mm) or less through the bracket. Slide the

bracket toward the front of the case and remove).

•Insert meter into the panel cutout.

•Install mounting brackets and tighten the screws

against the panel. To achieve a proper seal,

tighten the mounting bracket screws evenly until

meter is snug to the panel along its short side.

DO NOT OVER TIGHTEN, as the rear of the

panel may be damaged.

Figure 1. Panel Cutout and Mounting

Mounting Dimensions

Figure 2. Meter Dimensions – Side View

Figure 3. Case Dimensions – Top View

1.76"

(45mm)

0.59"

(15mm)

3.2"

(81mm)

2.45"

(62mm)

3.6"

(91mm)

Indice

Altri manuali Bin Master Strumento di misura

Bin Master

Bin Master DPM-400 Manuale utente

Bin Master

Bin Master BMRX-300 Manuale utente

Bin Master

Bin Master GWR-3000 Manuale utente

Bin Master

Bin Master PROCAP I Series Manuale utente

Bin Master

Bin Master BMRX-100 Manuale utente

Bin Master

Bin Master GWR-2000 Manuale utente

Bin Master

Bin Master MAXIMA+ Series Manuale utente

Bin Master

Bin Master DPM-500 Manuale utente

Bin Master

Bin Master CNCR-110 Manuale utente

Bin Master

Bin Master DPM-500 Manuale utente

Bin Master

Bin Master 1000 Manuale utente

Bin Master

Bin Master NCR-80 Manuale utente

Bin Master

Bin Master BMRX Series Manuale utente

Bin Master

Bin Master CNCR-210 Manuale utente

Bin Master

Bin Master 3DLevelScanner-MVL Manuale utente

Bin Master

Bin Master SMARTBOB TS1 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente